Web Device Management UI for long-range wireless video data link transmitter and receiver

Web Device Management UI for long-range wireless video data link transmitter and receiver

Users can view the current parameter configuration through the Web devices management UI and modify it according to the needs of the application, the user can access the device through the Network Port Browser, and the default IP address of the Sky end is 192.168.1 12, the default address of the ground end is 192.168.1 11.

Note: To change any configuration parameters via the web UI, users need to reboot the hardware system for the changed configuration to take effect.

Web Device Management UI for long-range wireless video data link transmitter and receiver
Web Device Management UI for long-range wireless video data link transmitter and receiver

Local IP: Nearby your computer, almost is the wireless video data receiver’s IP address;

Remote IP: Nearby the camera, almost it the wireless video data transmitter’s IP address.

Group IP: If you do not want to use broadcast mode, you can use multicast mode, the above Remote IP is changed to the multicast address, and all devices participating in multicast reception need to configure the same multicast address.

192.168.1.255 represents broadcast mode transmission

192.168.1.x represents point-to-point transmission

Note: DLB only supports multicast addresses in the 224.0.0.0~224.0.0.255 segments, considering that some addresses are reserved, it is recommended to use addresses above 224.0.0.23.

UI serial
Web Device Management UI serial

Uart1/Uart2/Uart3 correspond to D1/D2/D3 interfaces

Baudrate: Sets the baud rate of the corresponding data serial port on the local and remote devices.

Remote Port: UDP transmits the send port (different UARTS have to be configured with the different port numbers. )

Listening Port: UDP transmits the receive port (different UARTS have to be configured with different port numbers).

Maximum gap(ms): Set the maximum transmission interval of the corresponding serial port data (used to capture the end of the serial port data frame, it is recommended to configure it to be smaller than the actual transmission).

Maximum packet: Set the maximum sending frame size of the corresponding serial port data (the one that needs to be configured is larger than the actual transmission). note: When using UDP broadcast mode transmission, ensure that the values of Remote Port and Listening Port are different.

UI Wireless 1.4G
UI Wireless 1.4G

Frequency: Wireless band (800M/1.4G/2.4G).

Bandwidth: Wireless bandwidth (3M/5M/10M/20M).

Power: (without PA) output power (dBm).

UI Wireless-20M
UI Wireless-20M
UI Advance
UI Advance

Device Type: Central Node or Access Node.

Frequency Hopping: Automatic frequency hopping switch.

SMTP( Slave Max Tx Power): Access node maximum transmits power (dBm).

UI Debug
UI Debug

The Debug page is used to manually send AT commands or view real-time wireless feedback data.

Web Device Management UI for long-range wireless video data link transmitter and receiver 4
AES256 encryption

Set Password command

FormatATSP$(password),$(password)
For example: ATSP123456,123456
ParametersAES key password: 6-bit password (ASCII)
AES key password: 6-bit password (ASCII) (repeat to confirm)
PurposeUsed to set the AES key of the transceiver
Return valueFor example: ATSP123456,123456_
ATSP123456 OK
Remarks1. When the password is all 0, turn off AES encryption.
2. Set command, save when power off
AES256 Set Password

Once you’re on the Debug page, the browser shakes the Websocket handshake with the devices, and after the handshake passed, the browser prints “Websocket connect success.” “Indicates that the handshake was successful; otherwise it displays “Websocket connect failed, please refresh the web page and try again!” At this time, you need to re-enter the Debug page to shake hands again, until the prompt handshake is successful, and then you can perform follow-up operations.

UI measure
UI measure

Measure pages are used to call built-in iperf3 programs for testing (UDP mode).

Once you’re on the measure page, the browser will shake hands with the devices by WebSocket, and after the handshake passed, the browser prints “Websocket connect success.” “Indicates that the handshake was successful; otherwise it displays “Websocket connect failed, please refresh the web page and try again!” At this time, you need to re-enter the Measure page to shake hands again and know that the handshake is successful before you can perform follow-up operations.

UI system
UI system

This menu is used to view the device’s system software firmware version and to update the software firmware via the Web UI.

If you have any questions about the operation of Web Device Management UI, please feel free to contact us.

2W PA 27KM Real Test from mountain top to seaside Line-of-Sight

Latest 110km test video for the drone Long-range Wirless Video Transmitter and Receiver

Latest test video for the drone Long-range Wirless Video Transmitter and Receiver

NLOS wireless video transmitter and receiver test video in building indoor lift non line of sight

65 KM drone UAV Really fly Test Wireless Video Transmission

1.5km for ground NLOS, 10-20-30km LOS air to ground wireless video transmitter receiver transmission

80KM wireless transmitter-receiver Video Data RC Transmission System HDMI SDI long-range low latency

COFDM-912T NLOS (non-line of sight) 1.5km real test in city, buildings, trees and roads

Web Device Management UI for UAV wireless video data link transmitter transmission by IP Net camera

6.5 KM drone UAV Really fly Test Vcan1643 Main Feature

One HDMI Wireless Video Transmitter to many receivers for home meeting show room.

SDI Camera input encode board + Wireless Video Transmitter assembly DIY

COFDM-907T HDMI + CVBS input NLOS (non-line of sight) 1.5km real test in city, buildings

Cheapest CVBS RCA 720P Wireless Video Transmitter + 1080P Receiver Support 128 encryption

How to set encryption on the transmitter and receiver to protect your privacy

COFDM-912T Really test in the complex city environment, transmitter in the car, receiver in the building

Modify the COFDM Wireless Video Receiver to 890 900Mhz, out of normal DVB-T reception range

Cheap Wireless video transmitter and receiver's small screen has great help on signal strength lock

Modify our tv box to 445.5Mhz 7M bandwidth COFDM DVB T wireless transmitter transmission receiver box

COFDM-905T COFDM Wireless Video Transmitter with two board, Encode board and transmitter board

COFDM-905T Wieless Video Transmitter by CVBS video input test video

how to connect mini wireless HDMI video transmitter and receiver kit use android phone as receiver

OFDM Wireless Video Transmitter for IP Cameras Lightweight Long Range Transmission Automatic Network

Transmission Distance

PA Power Amplifier Inside

Flight Control Protocol

Transmitter Video Input

Wireless Transmit Method

Obstacle and Sight

Encrypt and decrypt

Transmission Carrier

Data Direction

For

Feature

FAQs about Wireless Video Transmitter and Receiver

Our wireless video transmitters have these types of video input interfaces: HDMI 1080P and 4K HDMI, CVBS composite, SDI, AHD, IP Ethernet, BNC, or tell us what type do you need, our engineer will modify to meet your demand.

Our transmission distance can be adjusted by adding power amplifiers. At present, the main ones are 15km, 30km, 50km, 80km, 100km , and 150km, which depend on the needs of customers.

Of course, the transmission distances listed above are all within LOS the line-of-sight range. If there are obstacles between the transmitter and the receiver, NLOS (the non-line-of-sight), the transmission distance is greatly reduced, only 1km or 2km, depending on the number of intermediate obstacles and the local wireless environment.

One-way means, We can only transmit and download video or data from the wireless video transmitter to the receiver in one direction, and we cannot upload video or data from the receiver to the transmitter. This type is also called simplex.

Two-way means that, not only we can download video or data from our wireless transmitter to the receiver, but also we can upload the video or data from the receiver to the transmitter. This is very suitable for operating drones. You can not only see the real-time video transmitted from the drone, but also upload the command to control the drone or the command to control the PTZ camera to adjust the angle to the transmitter. This can operate simultaneously. This type also named half-dulpex or full-duplex.

Please check the details at the below link. https://ivcan.com/request-a-quote-of-wireless-video-transmission/#simplex

Most Wireless video transmitters now support AES128 or AES256 bit encryption and decryption, depending on which model you choose. Please contact us to verify.

The frequencies of both the wireless video transmitter and the wireless video receiver can be modified. Users need to purchase additional parameter configuration boards.

However, considering that the corresponding power amplifier and antenna are already fixed within a certain range when the goods are sent out. If the user adjusts the frequency of the transmitter, the corresponding power amplifier, transmitter antenna and receiver antenna should also be modified to the same frequency, and these users need to be prepared. If not, it will cause the frequency of the wireless video transmitter to be different from the frequency of the antenna, making reception difficult. So please be sure to inform the correct frequency you need before placing an order.

If it is for security or confidentiality, you can use the encryption and decryption functions of the transmitter and receiver, which can ensure that your video transmission is private. .

Yes, all our product parameters can be customized according to customer's needs. If you have a special request, please let us know via the link below.

https://ivcan.com/request-a-quote-of-wireless-video-transmission/

  1. Change the place of the receiver to avoid potential local interference from strong magnetic environments.
  2. Ensure that the antennas on both the transmitter and receiver are vertical.
  3. Please raise the antennas of the transmitter and receiver to maintain a certain height difference.
  4. Please look around to ensure that there are no obstacles between the transmitter and receiver.
  5. Change the orientation of the receiver antenna.
  6. If it doesn't work, try moving the receiver to be near the transmitter's position to see if it exceeds the effective wireless transmission distance.
  7. Or consider adding a relay of the transmitting between the transmitter and receiver.
  8. The antenna should be as high off the ground as possible, as the ground will absorb the transmitted signal.
We can, of course, supply wireless video transmitter modules and power amplifiers.
For the first sample test, I recommend that you purchase the entire set of products because our engineers have optimized the parameters to achieve the best performance.
After you have completed your test verification, you can remove the case or heat sink, install it in your device, and constantly adjust the parameters to achieve the best performance. In the future, you will be able to purchase only the modules or accessories that you require.

Of course, we also understand that wireless video transmission transmitters and receivers are very expensive. You are far away from the China factory. and hope that the goods you receive are fit for the best performance.

If you pay special attention to a specific parameter or function, we can take some test videos based on the features you want to see, please feel free to contact us. It won't be shipped to you directly without your approval.

To test the delay of the wireless video transmitter and receiver, we need to do two tests.

The first is to test the delay from the camera to the display.

The second is the camera, plus the display plus the wireless image transmission transmitter and the delay of the receiver.

Subtracting the two test results is the real delay of the wireless video transmitter and receiver.

As a professional long-range HDMI wireless video transmitter and receiver supplier and manufacturer in China Shenzhen, we produce the best wireless video transmitter and receiver for many years, and we got a good reputation and best reviews.

Some famous brands of wireless video transmitters, like Blackmagic, Holyland mars 300 400s, Accsoon cine eye 5g, RavenEye, Zhiyun, Inkee benbox, actiontec, CVW SWIFT 800, dahua, iogear, Artek pat-225k, microlite, nyrius, teradek.

The best budget wireless broadcast video transmitter and the receiver have many applications, for 4K tv, CCTV security camera, vehicle backup camera, PTZ video camera kit, battery-powered, computer, sony camcorder, wifi video conference system, CANON DSLR, UAV drone, pc computer laptop, projector, in-car, iPhone iPad, live streaming, GoPro sports camera, raspberry pi, Xbox.

The full HD video, audio, data link smallest 1080P wireless video transmitter and the receiver has many input and output connectors, like AV composite CVBS, HDMI, SDI, BNC, VGA, USB.

The wireless video transmitter sender TX RX frequency has 170-806Mhz, 1.2ghz, 2.4G, 5.8G, lowest but not zero latency. In order to support longer distances, the power amplifier has 10w, 20watts, and even 30W.

What is a best buy FHD wireless video transmitter at a cheap price? It should consider your details requirement, choose suitably, not expensive, if you have any doubt, please fulfil the request a quote form, our engineer will offer you a solution.

Need Help on WhatsApp?
Scan the code