Rozmanitost dva RF demodulátor tuner MPEG-TS výstup dvojitá anténa DiBcom čip DVB-T COFDM přijímač RX modul

Vlastnosti

• Dual antenna reception, Anténní rozhraní SMA
• Receiving frequency band: 160MHz ~ 860MHz
• Single channel receiving sensitivity: -97±1dbm at QPSK 8MHz, -98±1dbm at QPSK 6MHz, the sensitivity increases by 3dbm when receiving with dual antennas
• Podpora mobilní příjem high-speed
• Podporované parametry:
  • IFFT：2K，8K
  • Interval ochrany: 1/4, 1/8, 1/16, 1/32
  • FEC：1/2, 2/3, 3/4, 5/6, 7/8
  • mapování modulace: QPSK, QAM16, QAM64
  • Bandwidth: 1.8MHz~8MHz, step 0.1MHz
• The demodulated digital signal output interface is J3 interface (TSI)
• Kontrolka napájení, work indicator light
• Hmotnost PCBA: 13.4 gramů
• velikost desky: 51mm x 30 mm

Poznámka

This demodulation module is pure hardware and does not contain an MCU, so it cannot run independently. It can be used as a plug-in module to output TS streams. You need to design it yourself or use our baseboard to work.

This is a dual antenna receiver that outputs TS stream (physical interface). There is no MCU on the module and it cannot be used alone. Customers buy this module and integrate it into their own products, and they also need to transplant the driver into their own products.

This module itself does not have code and cannot be used alone. An external chip is required to load the firmware into it (similar to the early WiFi modules)

J3 Pin interface defines

The J3 interface is a 2×10 20pin 1.27mm pitch straight pin header, which is used to connect our module and the decoder board. It uses TSI to transmit data. Its signal definition is shown in the table below:

PIN serial number	směr	signal name	popsat
1	DOVNITŘ VEN	HOST_BUS0	Data DR2C I2C
2	DOVNITŘ VEN	HOST_BUS1	Hodiny DR2C I2C
3	v	RESET_IN	DR2C reset
4	PWR	GND	signal place
5	PWR	VDD_5V	DR2C 5V power input
6	VEN	HOST_BUS2	Údaje TSI0
7	VEN	HOST_BUS3	Údaje TSI 1
8	VEN	HOST_BUS4	Údaje TSI 2
9	VEN	HOST_BUS5	Údaje TSI 3
10	VEN	HOST_BUS6	Údaje TSI4
11	VEN	HOST_BUS7	Údaje TSI5
12	VEN	HOST_BUS8	Údaje TSI 6
13	VEN	HOST_BUS9	TSI Data 7
14	VEN	HOST_BUS10	TSI Frame Indicator
15	VEN	HOST_BUS11	TSI Sync
16	VEN	INT_SELECT1	Vyberte režim DR2C
17	VEN	HOST_BUS12	Hodiny TSI
18	V	HOST_BUS13	Selhání FEC
19	PWR	VDD_3P3V	DR2C 3.3V power input
20	PWR	GND	signal place

Module Mechanical Dimensions

demodulátor + Decoder board

Nejčastější dotazy:

Q1: Is the TS output of your demodulation chip serial or parallel?

A1: Parallel.

Q2: Does your module support TS output?

A2: Ano. This module J3 contains an output physical interface.

If you need to match it with our decoding baseboard, it not only has HDMI and CVBS output, but also contains an Ethernet port. This Ethernet port supports the output of TS video streams, which can be played on Windows or Linux through VLC player.

Q3: Can I buy a sample of this diversity RF DVB-T demodulator with TS output interface module?

A3: We are happy to provide you with samples. We have to remind you that this is a pure hardware product. In addition to two RF inputs and a J3 interface, there is no separate power supply and video output port, and there is no MCU and firmware on this module, so it cannot be run and tested alone.

If you need to test, please purchase it together with its baseboard (zdroj napájení, decoding chip and HDMI/CVBS/Ethernet output). See the picture above. When you understand its performance, you can develop your hardware or peripheral circuits, or we are also happy to provide technical support.

Q4: Can you provide me with the source code and driver? I need to program it.

A4: We need to consider your project requirements and purchase volume before we can provide code and source programs. We are happy to cooperate with you.

Q5: Can the DiBcom handle higher-frequency inputs? The 2.0-2.9 GHz frequency band is available to me.

A: DiBcom 9090MA only supports 170-860Mhz. Please use frequency down conversion to support 2~2.9Ghz.

More About this product

The DiBcom 9090MA is a chipset designed for DVB-T (Digitální video vysílání – Pozemní) recepce. It is commonly used in USB TV tuners, automotive applications, a vestavěné systémy. Here’s a detailed overview of its features and setup, particularly for handling TS (Transport Stream) výstup.

---

DiBcom 9090MA Overview

1. Core Features:

   • DVB-T Support: Compliant with the DVB-T standard.
   • Vysoká citlivost: Optimized for reliable reception, i v náročných prostředích.
   • Příjem rozmanitosti: Supports antenna diversity for better signal quality.
   • Transport Stream (TS) Výstup:
     • Delivers MPEG-2 TS over a variety of interfaces.

2. Rozhraní:

   • I2C Interface: For control and configuration.
   • TS Output:
     • Parallel TS or serial TS modes, selectable based on the application.
     • Outputs MPEG-2 TS for decoding or further processing.

3. Aplikace:

   • Wireless COFDM Video receiver
   • USB DVB-T tuners for PCs and embedded systems.
   • Automotive DVB-T receivers.
   • Digital TV integration in portable devices.

---

Transport Stream (TS) Výstup

The DiBcom 9090MA outputs MPEG-2 Transport Streams, which is the standard for digital TV broadcasting. Takto to funguje:

1. TS Data Format:TS

   • Comprises packets of 188 bajtů.
   • Contains video, Zvuk, and metadata multiplexed into a single stream.

2. TS Output Modes:

   • Parallel TS:
     • výstupy 8 bits of data per clock cycle.
     • Requires more pins but provides faster data transfer.
   • Serial TS:
     • výstupy 1 bit per clock cycle.
     • Uses fewer pins but may be slower.

3. Clock Signal:

   • The chipset provides a clock signal to synchronize the TS data output.

4. Control Signals:

   • Data Valid (DVALID): Indicates valid data on the TS bus.
   • Synchronizovat: Signals the start of a TS packet.

---

DiBcom and TS output Integration Steps

1. Hardwarové připojení:

   • Connect the TS output pins (parallel or serial) to a demultiplexer or decoder.
   • Use an I2C interface to configure the tuner.

2. Configuration via I2C:

   • The 9090MA needs to be configured through I2C commands for:9090MA
     • Channel frequency.
     • Bandwidth (6, 7, nebo 8 MHz).
     • TS output mode (parallel or serial).

3. TS Decoding:

   • Feed the TS output to a compatible decoder, such as an MPEG-2 decoder or software-based solution.

4. Softwarová integrace:

   • Use Linux DVB APIs (pokud je to možné) for capturing and processing TS data.
   • Applications like Přehrávač médií VLC or custom software can decode and display the TS.

---

Případy použití

1. USB DVB-T Tuners:USB DVB-T：
   • Combine with a USB interface IC (NAPŘ., Cypress EZ-USB) for PC-based TV tuners.
2. Automotive Receivers:
   • Use diversity reception with two or more 9090MA chips for stable reception in moving vehicles.
3. Vestavěné systémy:
   • Integrate with ARM-based boards to provide DVB-T functionality in custom devices.

---

Example Application Circuit

1. Komponenty:

   • DiBcom 9090MA as the tuner chip.
   • A RF front-end for antenna and signal conditioning.
   • I2C rozhraní connected to a microcontroller or CPU.
   • TS output connected to a decoder or USB bridge.

2. TS Output Example:

   • Parallel Mode:
     • Data lines: TS[7:0].
     • Control lines: CLK, DVALID, and SYNC.
   • Serial Mode:
     • Single data line: TS_DATA.
     • Clock and control lines.