Integrated Ground Receiver and Antenna with Tripod for Drone UAV Radio Link
Table of Contents
Introduction
This is a TDD two-way integrated ground receiver. It has two structural forms, 2133T and 2133X. Both devices support multiple interfaces such as wifi, network port, serial port, SBUS and asynchronous RS422, and both support independent battery pack power supply and external power supply. Both devices are easy to assemble and disassemble. 2133T and 2133X have versions with different transmission powers such as 2/5/8/10/20W. They support a series of functions, such as real-time environmental noise detection, adaptive bit stream, automatic frequency selection, automatic retransmission mechanism, automatic antenna selection, automatic power control, manual frequency binding mode, and multiple coexistence.
2133X uses 2 omnidirectional antennas. Under line-of-sight conditions, it can support a transmission distance of about 30 km with a 2W transmission power; 50 km with a 5W transmission power, 80 km with a 8/10W transmission power, and 100 km with a 20W transmission power.
2133T use one flat panel directional + one omnidirectional antenna combination solution Therefore, 2133T generally has better transmission performance than 2133X. Under line-of-sight conditions, 2133T can support a maximum transmission distance of 60km at 2W air-to-ground transmission power, 100km at 5W/8W air-to-ground transmission power, 150km at 10W air-to-ground transmission power, and 200km at 20W air-to-ground transmission power.
Feature
- Support long distance transmission: The maximum transmission distance under air-to-ground line of sight is about 200km.
- Support large bandwidth transmission: Maximum supported rate is 17Mbps@10MHz.
- Support automatic relay transmission: Supports automatic joining of relays.
- Support multi-interface: Support Ethernet port, WIFI, RS232, TTL, RS422, SBUS.
- Support automatic frequency selection: Automatically detect interference signals and select the optimal frequency in real time.
- Support automatic retransmission: Automatically retransmit burst error data to improve data reliability.
- Support adaptive bit stream: Automatically adjust channel modulation mode according to signal quality in real time.
- Support automatic power control: Automatically adjust the transmission power at close range to reduce power consumption.
- Support automatic antenna selection: Select the optimal antenna for transmission based on the obstruction situation in real time.
- Support dynamic allocation of uplink and downlink: The master-slave upstream and downstream bandwidth ratios can be automatically allocated in real time according to the data volume.
- Support multiple coexistence: Support multiple sets of equipment working at the same time.
- Support frequency binding function: Frequency pairing can be performed through software and hardware.
- Support IP53 protection: Adopt rainproof and dustproof design.
Specification
| Model | 2133X | 2133T |
| Antenna type | 2x Fiberglass Omnidirectional Antenna | 1x Fiberglass Omnidirectional Antenna + 1x Flat Panel Antenna |
| Working frequency band | 1350~1470MHz | 1350~1470MHz |
| RF Channel | 2T2R | 2T2R |
| Transmit power | 33/37/39/40/43dBm
(2W/5W/8W/10W/20W) |
33/37/39/40/43dBm
(2W/5W/8W/10W/20W) |
| Transmission distance* | Air-to-ground visibility is about 30KM@2W;
Air-to-ground visibility is about 50KM@5W; Air-to-ground visibility is about 80KM@8/10W; Air-to-ground visibility is about 100KM@20W; |
The maximum air-to-ground visibility is 60KM@2W;
The maximum air-to-ground visibility is 100KM@5W/8W; The maximum air-to-ground visibility is 150KM@10W; The maximum air-to-ground visibility is 200KM@20W; |
| Channel bandwidth | 10MHz | 10MHz |
| Modulation | QPSK/16QAM | QPSK/16QAM |
| Receiving sensitivity | See Table 2 | See Table 2 |
| Maximum rate | 16.8Mbps@16QAM3/4 | 16.8Mbps@16QAM3/4 |
| Communication encryption | AES256 | AES256 |
| Transmission delay | ≤10ms | ≤10ms |
| RF Interface | N head*2 | N head*1 |
| Data Interface | Ethernet*1; WIFI *1 | Ethernet *1; WIFI *1 |
| TTL/RS232*2; RS422*1; SBUS*1 | TTL/RS232*2; RS422*1; SBUS*1 | |
| Power consumption | ≤15W | ≤15W |
| Protection level | Air unit IP20, ground unit IP53 | Air unit IP20, ground unit IP53 |
| Product size | 250mm*150mm*34.4mm | 259mm*259mm*76mm |
| Product Weight | About 1.5KG | About 1.5KG |
| Operating voltage | DC9~36V | DC9~36V |
| Operating temperature | -40~+65℃ | -40~+65℃ |
iVcan.com –
ChatGPT 说：
I have been using this integrated ground receiver and antenna with tripod for long-range drone UAV radio link, and I am very satisfied with its performance. Having all functions in one unit makes it extremely convenient and easy to operate, saving a lot of time during setup. The reduced installation and connection steps are especially valuable when working in urgent situations where quick deployment is critical. The tripod design provides stability, and the signal reception is strong and reliable even at long distances. Overall, this receiver is well-designed, efficient, and highly practical for professional drone operations requiring fast and dependable performance.