Modulo di rete ad hoc SNM401

1. Descrizione del prodotto

SNM401 Centerless Ad Hoc Network Module realizes centerless long-distance communication between modules, and adopts the world’s latest LDPC encoding and decoding technology, compared to the RS level used by traditional radio stations The concatenated convolutional code can have a coding gain of 5dB, e allo stesso tempo, attraverso il “self-relay wireless communication” tecnologia, it innovatively realizes automatic relay between modules, thereby greatly improving the coverage effect and transmission distance. SNM401 adopts ad-hoc network wireless communication technology, any node can receive and process the same signal forwarded by multiple nodes at the same time, combine these signals forwarded from different nodes, demodulate the original information to the greatest extent possible, and have a larger transmission distance and higher transmission reliability. The wireless communication technology of the ad hoc network does not require routing, and multiple nodes automatically determine whether to start the forwarding according to the received signal quality and field strength, and the relay is upgraded from a multi-hop single-point relay to a multi-hop multi-point relay. The state relay is upgraded to a mesh relay. When any node in the relay network is disconnected from the network, other relay lines in the relay network work normally so that the relay effect is not affected.

2. Caratteristiche del prodotto

◆Operating frequency: 400-500MHz

◆Single-hop transmission distance: 3~5Km

◆Dynamic topology convergence: 1Signorina

◆Transmit power: 1W

◆Receive sensitivity: -127dBm

◆Working voltage: 3.5-4.5V

◆Signal to noise ratio Threshold: 1dB

◆Channel spacing: 12.5KHz

◆Frequency stability: 1ppm

◆Intermodulation: 65dB

◆Encryption: 256AES

◆Spurious response immunity: 75dB

◆Adjacent channel selectivity: 65dB@12,5KHz

◆Operating temperature: -40～ +85℃

◆Module size: 33.5X42X3,4 mm

3. Applicazione

◆Internet of Things ◆Individual Soldier System ◆Emergency Broadcasting

◆UAV ◆Real-time Remote Control ◆Digital Intercom

◆Emergency Communication ◆Robot ◆Wireless Data Transmission

4. Working Parameters

Tavolo 1: Operating Parameters Table

Parametro	Condizioni	Minimo	Tipico	Massimo	Unità
Banda di frequenza operativa		400		500	MHz
temperatura di esercizio		-40	25	+85	℃
Tensione di funzionamento		3.5	4	4.5	V
Transmitting Power			30		dBm
Ricezione di sensibilità		-130	-127	-125	dBm
Maximum RF Input Power				+33	dBm
baud rate della porta seriale			115200		bps
sleep current	@EN=0		40		Fare
Ricevi corrente			160		mA
transmit instantaneous current	@VCC==4V, 1W			1800	mA
transmit average current	@VCC==4V, 1W		600		mA
audio input voltage				1.5	VPP
audio output Impedance			150		Ohm

Nota: Se le condizioni di lavoro del modulo superano i valori limite di cui sopra, potrebbe causare danni permanenti al modulo.

5. Module pins and definitions

Figura 1 SNM401 Pin Diagramma

Abbreviation	Descrizione
AI	Ingresso analogico
AL	Uscita analogica
Aio	Bidirezione analogica
DI	Input digitale
FARE	Output digitale
DIO	Bidirezione digitale
P	Energia
sol	Terreno

Tavolo 3 SNM401 pin definition

PIN NO	Nome del perno	Tipo	Descrizione
1	GND	sol	GND
2	FORMICA	Aio	antenna port
3	GND	sol	GND
4	GND	sol	GND
5	VBAT	P	External 3.5V-4.5V battery or power supply, 4V is recommended
6	VBAT	P
7	GND	sol	GND
8	GND	sol	GND
9	STATO_TX	FARE	module transmit indication Signal, the high level is transmitting
10	RX_STATO	FARE	module receiving indication signal, the high level is receiving
11	NC		Nessuna connessione
12	NC		Nessuna connessione
13	GND	sol	GND
14	TXD	FARE	serial port data transmitting pin
15	RXD	DI	serial port data receiving pin
16	IMPOSTATO	DI	module Serial port configuration signal, configure parameters when high level, send and receive data when low level
17	IN	DI	module open enable signal, high level open, low level close
18	GND	sol	GND
19	PRO1	DIO	programmable definition pin
20	PRO2	DIO	programmable Definition pin

: The module is regulated by 3.3V LDO inside, and all digital IOs are 3.3V level.

 

6. formato del pacchetto

Figura 2 SNM401 size chart

Figura 3 SNM401 package Figure

7. LAYOUT precautions

1.IlSNM401 module works at 400-500MHzand the influence of various factors on wireless transceivers should be avoided.

2. Esso is laid under the module GND, and the traces are extended to the periphery as far as possible.
3. It is recommended to use insulating material to isolate the module mounting position on the substrate, per esempio, place a whole piece of in this position

silkscreen

4. Try to take a short and thick power line to the module, the recommended copper line width is80mil, and the decoupling capacitor should be placed as close to the power pin as possible.

8. Software configuration

8.1 Configurazione dei parametri

Users can obtain and configure parameters through the serial port, the serial port baud rate è 115200, the data bit is 8po, the stop bit is 1po, and there is no parity bit.

Tavolo 4 Serial port packet format

Serial port table packet
identification word	lunghezza	Comando	instruction reply/reply content
1Byte	1Byte	1Byte	N Byte

8.1.1 Identification word

The identification word is fixed as 0x68.

8.1.2 Lunghezza

Lunghezza Calcolo della velocità di trasmissione del sistema di trasmissione wireless COFDM comando + command content/reply content.

8.1.3 Comando

diametro della colonna 5 Serial Command-List

Funzione	Comando	Soddisfare	Reply Content
Acquire RF Parameters	0x00	No	Frequenza(4Byte) +Energia(1Byte) +Configurazione Stato(1Byte) +Rumore(2Byte) +Baseband Version Number(1Byte)
Set RF Parameter	0x01	Frequenza(4Byte) +Energia(1Byte)	No
data relay level	0x0C	No	data relay level(1Byte)
Set data relay level	0x0D	Data relay level(1Byte)	No
key to acquire	0x0E	No	chiave(32Byte)
set key	0x0f	chiave(32Byte)	no
get module version	0x12	no	module name + version number
module ready	0x55	no	no
save configuration	0x66	no	no
data receive	0xA2	no	dati trasparenti (N Byte)
data send	0xB2	dati trasparenti (N Byte)	no

8.1.4 Instruction content/reply content

8.1.4.1 Obtaining RF parameters

Frequenza: L'unità è Hz, the setting range is ~5000000000, and the precision is 500HHz.

Energia:1-alta potenza 1W,0-bassa potenza 0.5W, the default is high power 1W.

Configuration status: Indicates the radio configuration status,0-uninitialized,1-configuring,2-configured successfully.

Noise Floor: Indicates the current frequency noise intensity, quale 2 is meaningful

Baseband version number: The upper 4 bit represent the major version number, and the lower 4 bit represent the minor version number.

Configuration Packet:0x680x010x00

Return Packet:0x68 0x0A 0x00 Frequency Power Configuration Status Noise Floor Baseband Version No.

8.1.4.2 Setting RF Parameters

After configuring RF parameters, you must wait for the successful configuration (di 2 secondi) before the module can enter the setting work correctly state.

Configuration package:0x68 0x06 0x01 Frequency power

return package:0x680x010x01

8.1.4.3 Obtaining data relay level

SH ad hoc network technology is a simulcast mesh relay method, which does not require routing, which can greatly improve the coverage.number of relay hops N refers to the number of hops that can be relayed during data transmission, and the maximum number of relay hops is 16. With each additional hop, the transmission distance doubles, but the transmission time increases accordingly, as shown in the table below.

Tavolo 6 Comparison of Relay Levels

Relè hop	Transmission Bytes	Transmission Time
N	<36	N*50ms
N	37-72	N*100ms
N	73-108	N*150 ms
N	109-144	*200Signorina
N	145-180	N*250 ms
N	181-216	N*300 ms
N	217-252	N*350ms
N	253-288	N*400 ms

Configuration package: 0x68 0x01 0x0C

Return package: 0x68 0x02 0x0C Data relay level

8.1.4.4 Set data relay level

Configuration package:0x68 0x02 0x0D Data relay level

return packet:0x68 0x01 0x0D

8.1.4.5 Obtain the key

key for communication encryption, the module will automatically discard the voice information and data information whose key is inconsistent with its own key, and the key is all 0.

Configuration Packet:0x68 0x01 0x0E

Return Packet:0x68 0x21 0x0E Chiave

8.1.4.6 Set Key

Configuration Packet:0x68 0x21 0x0F Chiave

Return Packet:0x68 0x01 0x0F

8.1.4.7 Get Module Version

Configuration Packet:0x680x010x12

Return Packet:0x68 0x15 0x12 0x53 0x69 0x6d 0x75 0x6c 0x48 0x6f 0x63 0x32 0x31 0x38 0x5f 0x31 0x31 0x30 0x2e 0x30 0x00 è“Simulhoc2618_V1.0.0”

8.1.4.8 modulo

Return package:0x680x010x55

8.1.4.9 Save configuration

command to save all settings to Veloce, and the saved configuration will be used directly after power-on.

Configuration package:0x680x010x66

Return package:0x680x010x66

8.1.4.10 Data reception

When the IMPOSTATO pin is low, the module will transparently transmit the received data package to the user. The length varies according to the actual transparent transmission data length.

Return package:0x68 Lunghezza 0xA2 Trasparente

8.1.4.11 Trasmissione dati

Only when the IMPOSTATO pin is at a low level can data be transmitted, and the data sent in a single transmission does not exceed 36 byte. The length varies according to the actual transparent transmission data length. If a return packet is received, it indicates that the data transmission failed this time.

Configuration package: 0x68 Length 0xB2 Transparent data

return package: 0x68 0x01 0xB