Modulo di trasmissione trasparente Ethernet wireless COFDM Trasmettitore e ricevitore dati video FDD RJ45 da 100 Mbps

Mini COFDM wireless Ethernet transparent transmission module 100M bps RJ45 FDD video data transmitter and receiver for UDP IP camera

Introduzione

1. This is a broadband cofdm wireless video data transmission module. Both the transmitter and receiver modules have an RJ45 network and UART data and control interface.
2. The network port on the transmitter can be connected to the IP camera as the video source for wireless transmission, and it can also be connected to the data source of the network port, which is transmitted to the receiving module through COFDM technology. The receiver also has an RJ45 network and data UART control port, and it supports UDP playback on the PC.
3. The frequency can be modified through the UART serial port, or one-way data transmission can be added to realize the requirement of remote frequency modification without powering off to restart.
4. There are two RF antennas on this transceiver module, one is TX and the other is RX, which can realize two-way transmission of video and data. Two different frequency ranges need to be set, and BPF filters are used to filter clutter and avoid mutual interference.
5. This model can run the CMD Ping command and get a response. (video on youtube)
6. This is adopted by FDD technology.
7. The default working frequency is 340Mhz and 590Mhz. (Other frequencies can be adjustable from 170~860Mhz)
8. It does not include any power amplifier.
9. Support one-way directional transmssion.

Caratteristiche

• Piccola dimensione. Length 70MM, width 50MM, height 20MM
• Basso consumo energetico. In the case of 2M bandwidth, 12V, current 200mA
• RF performance is good. Spurs low
• Buona compatibilità di larghezza di banda. Bandwidth 2M~8M bandwidth adjustable on the same board, passo 100KHz
• Alimentatore ad ampia tensione. Intervallo di tensione di alimentazione: 6V~20V.

Funzione

1. Parametri regolabili

IFFT：2k

Intervallo di guardia: 1/4, 1/8, 1/16, 1/32

FEC：1/2、2/3、3/4、5/6、7/8

Mappatura della modulazione: QPSK (4QAM), 16QAM, 64QAM

Larghezza di banda: 2Larghezza di banda M~8M regolabile, passo 100KHz

2. 128-crittografia a bit

The module supports 128-bit encryption, and the decryption requires the cooperation of the decryption board

3. Parametri della porta seriale di controllo della comunicazione (RS232, not TTL)

8 bit di dati

1 fermati un po'

addirittura parità

Velocità di trasmissione: 19200

4. Support full-duplex 100M Ethernet transmission, support TCP, UDP.

TCP supports point-to-point transparent Ethernet transmission.

UDP supports point-to-multipoint transparent Ethernet transmission, IEEE 802.3 AND 802.3u.

5. Frequenza RF

Il transmitter frequency range supports from 50MHz to 2.5GHz, with a step of 100KHz

Il receiver frequency range supports from 158MHz to 860MHz, stepping 100KHz

6. La potenza di uscita RF è controllabile

RF output power attenuation is adjustable from 0dB to 15dB

7. Support one standard RS232 data serial port

Connettore

Spillo 7-12: Connect the Xilinx’s programmer, update the new firmware from the computer

Dimensione

COFDM Transceiver package details.

Parameter Configure Board

Connessione

• The sending end of the control serial port of the keyboard is connected with the receiving end of the module serial port
• The receiving end of the control serial port of the keyboard is connected to the sending end of the module serial port
• The ground of the control serial port of the keyboard is connected with the ground of the serial port of the demodulation board
• The LCD interface of the keyboard is connected to the LCD interface of the LCD board with a flat wire, and pin 1 corresponds to pin 1.
• The module and the keyboard must be connected to the 12V power supply, and the LCD board does not need to be connected to the power supply

Electrical Characteristics

• Alimentazione CC, voltage 6V~20V
• Raccomandazione: The power supply voltage is 12V, and the current is 200mA~300mA

Parametri tecnici

• Potenza di uscita RF -15 ±3 dBm (less than 1GHz, greater than 1G, need to be measured). Nota: Qui -15 ±3 dBm is the peak power. When we customize the PA (amplificatore di potenza) for this COFDM ethernet transceiver, we need to make the PA according to the average power -5dBm.
• Carrier-to-noise ratio >40dB （It is the difference between the highest point of the spectrum analyzer and the point going out from the bottom）

Customize for you

1. 1886 Transceiver module
2. Amplificatore di potenza: 1watt, 2watt, 5watt, 10watt, 20watt, 50watt
3. Band-pass Filter
4. Convertitore di frequenza verso il basso
5. Transmitter Antenna, Receiver Antenna.

What does this module do?

1. Because this module supports different frequencies for transmitting and receiving, if you have two modules to form a pair of transmitters and receivers, the working frequency can be customized from 170 to 6000Mhz. (Receiving requires additional down-conversion)
   Per esempio, one is used in a ground control station and the other is used in an aerial drone. The uplink frequency is 860Mhz and the downlink frequency is 230Mhz, so that even if the wireless link is interfered by the ground counter-drone, it can still control the drone to return safely.
2. Because this module has both receiving and transmitting functions, it is often used as a relay for COFDM digital video transmission. When placed in the middle of some digital vide transmissions as a repeater, it can solve the obstruction of obstacles such as mountains, and can also enhance the signal in the middle to extend the wireless transmission range.

1. Some Simple FAQs before you understand this product Vcan1886.

1. Does the pair of devices implement a transparent ethernet pipe? sì
2. Is there a limit to the number of devices (MAC addresses) each side of the device can handle? NO
3. What is the maximum bandwidth per stream (RX e TX)? up to 30Mb
4. Are the RX and TX streams equivalent, or does one of them have higher priority (eg, higher bandwidth)? NO
5. Are there any restrictions on the type of traffic (especially multicast, trasmissione) that the device can transmit? NO
6. Are there any limitations to the support of IP protocols (TCP, UDP, ICMP, SCTP), especially in the case of two-way communication? nessun limite

2. Can I change the transmitter frequency in real-time from the receiver?

1. sì, si prega di controllare the test video at youtube.
2. Download Vcan1886 communication control protocol
3. Here is an example of a UART control command to modify the frequency.
   1. Modify the Transmitter frequency to 615Mhz.
   2. In units of 100KHz, 615Mhz should wright 6150
   3. 6150 in decimal is equal to 1806 in hexadecimal
   4. Alto: Fixed format 0003+18+[03+18=1B]，so {0003181B}
   5. Basso: Fiexed format 0004+06+[04+06=0A], so {0004060UN}
   6. {00000101} restart
   7. {00000000} reset
   8. Modify the Transmitter frequency to 700Mhz.
   9. In units of 100KHz, 700Mhz should wright 7000
   10. 7000 in decimal is equal to 1B58 in hexadecimal
   11. Alto: Fixed format 0003+1B+[03+1B=1E]，so {00031B1E}
   12. Basso: Fiexed format 0004+58+[04+58=5C], so {0004585C}
   13. {00000101} restart
   14. {00000000} reset
   15. Modify the Transmitter frequency to 600Mhz.
   16. In units of 100KHz, 600Mhz should wright 6000
   17. 6000 in decimal is equal to 1770 in hexadecimal
   18. Alto: Fixed format 0003+17+[03+17=1A]，so {0003171UN}
   19. Basso: Fiexed format 0004+70+[04+70=74], so {00047074}
   20. {00000101} restart
   21. {00000000} reset
4. Please contact us if you need any futher test video, we will show you details.

3. Some simple FAQ talking about the frequency and power amplifier.

1. The lower frequency is better. Can you provide the antennas with the lowest frequency?

iVcan.com: the frequency is adjustable by Menu Board and Parameter Configuration screen from 170-860Mhz. Once you confirmed the working frequency, the antenna factory will customize antenna according to your confirmed frequency.

Please note that there are two working frequencies here, and try to set the frequency interval to be larger to avoid interference. Such as 340Mhz and 590Mhz. If your antenna and power amplifier have a large working range, you can modify the working frequency at any time after configuring the antenna and power amplifier.

2. Are these antennas flexible?

iVcan.com: Antenna type and length can be customized according to your demand.

Here we listed some antenna with price for your references.

https://ivcan.com/price-list-for-wireless-video-transmitter-and-receiver-antenna/

3. If I get it right these modules require power amplifier?

iVcan.com: As the default package, there is no power amplifier. Most time, the antenna and amplifier have to customize to produce according to your confirmed the working frequency. It also need set different watts (2W, 5W, 10W or 20W) according to your transmission distance.

4. Is a power amplifier configured for a specific frequency?

iVcan.com: We can offer you the power amplifier according to your demand. This has extra charge. Power amplifier customized by hardware, it can not configure by software or firmware.

Here are some power amplifiers for your references.

https://ivcan.com/p/pa-power-amplifier-1w/

https://ivcan.com/p/2-watts-5-watts-10-watts-pa-linear-power-amplifier-rf-module-board-pcba/

5. Can we reconfigure power amplifier by ourself?

iVcan.com: Sicuro, you can buy extra power amplifier for this transceiver module.

6. Do you have wide-band power amplifiers for a few watts?

iVcan.com: NO, our power amplifier working frequency is always +/-15 Mhz. For Example 580~610 Mhz.

7. The price is for two modules as in the picture?

iVcan.com: sì. Our quotation is on the base of one pair transceiver. (2pz, 1 trasmettitore, 1 ricevitore)

8. What is the working range of the COFDM transceiver without the power amplifier?

The COFDM transceiver module can only reach 40~50 meters without a power amplifier.

4. Can I choose 900 MHz and 2.4G as the TX RX working frequency?

1. Although our two-way wireless network port transceiver module supports transmit frequency, which can be selected from 50Mhz to 2500 MHz, the receiving frequency range can only be between 170~860Mhz;
2. if you choose 900Mhz and 2400Mhz as the transmitting and receiving frequency, you must add an up-converter block and down-converter block, frequency filters, amplificatori di potenza, and other devices.

5. Do these modules work as a point-to-multipoint?

1. NO.
2. Only Point-To-Point.

6. Can we use the UART interface on board to transmit MAVLink or sbus?

1. sì
2. Needs use UART to Sbus converter board. Please tell us if you need this function, we will change the UART to Sbus for you before delivery.

7. Can you show me the picture of one full set COFDM transceiver with default antenna?

Vcan1886_Mini_COFDM Ethernet IP transceiver module

The above picture is default COFDM transceiver module.

(default antenna is 340Mhz and 550Mhz for testing)

Most clients need to customize the PA (amplificatore di potenza), transmitter and receiver antenna, frequency filter, you should tell us.

1. PA (amplificatore di potenza), increase signal strength for longer transmission range.

2. Transmitter and receiver antenna: There are two frequencies for transmitting and receiving. You should tell us, for example 170Mhz or 380Mhz.

3. Frequency filter: filtro passa banda, to avoid the frequency interference.

4. Metal box: Maybe you also need a metal box to assemble the above module parts.

Details on customization parts, per favore controlla qui.

8. Can you customize one full set for me? 340 Mhz and 554 Mhz with 5 watts PA and filter, metal box, and antenna?

Please contact us if you need customize for your project.

9. Can it operate in one-way mode if the air unit loses ground unit data?

It Supports.

This model has two frequencies, and the uplink and downlink can use different frequencies, such as 300Mhz and 500Mhz. It supports network video input, TCP protocol that requires handshake, UDP transmission protocol, COFDM one-way transmission, and the uplink can continue to work even if the downlink is interfered.

Peso

*

Menu and key operation instructions

menu 1

Power on and start to enter menu 1, and enter menu 2 after communicating with the board

If the status of the emission section is set to work, press the left button to 4.

If the status of the receive section settings is Working, press the right key to 3.

Up and down keys and exit, the OK key does not work

Press the MENU key to enter menu 5.

Press OK and Exit at the same time to enter menu 16 and save all the parameters of the channel. (In questo modo, the control panel can be used, and the module will run with the saved parameters after power-on last time)

menu 3

Press the up or down key to change the receiving channel, if there is a new channel, enter the menu 31

Press the left key or the escape key to return to menu 2.

Press the menu key to jump to Menu 5

menu 31

Up or down keys to change the transmission channel

Press OK to return to menu 32.

Escape key to return to menu 3

Other keys have no effect.

menu 32

Dopo 1 secondo, return to menu 3.

Other keys have no effect.

Menu 4:

Up or down key to change the transmission channel, if the channel is changed, enter menu 41

Press the right key and exit key to return to menu 2.

MENU key to enter menu 5.

Menu 41:

Up or down key to change the transmission channel.

Press OK to enter menu 42.

Press the exit key to return to Menu 4

Other keys do not work

Menu 42:

Within 1 secondo, return to menu 4.

Other keys have no effect.

Menu 5:

3 N E W R X C H A N N E L

4 D E L T X C H A N N E L

5 DEL RX CHANNEL

6 SET MODULE STATUS

7 SEP DATE WITH

The cursor stops at 1 when entering,

Press the up or down key to move the cursor.

Ok key to select the number corresponding to the cursor. Scegliere 1: jump to 6, choose 2: jump to 7, choose 3: jump to 8, choose 4 to jump to 9; choose 5, jump to 91; choose 6, jump to menu 15; choose 7, jump to menu 17.

Escape key, and return to menus 2 O 3, O 4.

The left button, right button, and the menu don’t work.

Menu 6:

Left and right keys to move the cursor,

Press the up or down key to change the number that the cursor is on,

OK key to return to menu 2 O 3, O 4.

Escape key or menu key to return to menu 5

Menu 7:

Left and right keys to move the cursor,

Press the up or down key to change the number that the cursor is on,

After pressing OK, skip to menu 2 when done.

Escape key or menu key to return to menu 5

Menu 8:

Left and right keys to move the cursor,

Press the up or down key to change the number that the cursor is on,

After pressing OK, skip to menu 10 when done.

Escape key or menu key to return to menu 5

Menu 9:

Up and down keys to change the channel number.

After selecting OK, skip to menu 14

Escape keys 2 O 3, O 4.

MENU key to return to 5

other keys don’t work

Menu 91:

Up and down keys to change the channel number.

After selecting OK, skip to menu 141

Escape key to return to menu 2

MENU key to return to 5

other keys don’t work

Menu 10:

all keys do not work

For frequency locked, go to menu 12, if not locked, go to menu 11

Menu 11:

Left and right keys to move the cursor,

Press the up or down key to change the number on the cursor, if changed, return to menu 8

After pressing OK, skip to menu 10 when done.

Escape key or menu key to return to menu 5

Menu 12:

After pressing OK, jump to menus 2 O 3 O 4 when done

Escape key or menu key to return to menu 5

other keys don’t work

menu 14

Jump back to menu 9 after the selection

menu 141

Jump back to menu 91 after the selection

menu 15

Left and right keys to move the cursor,

Up and down keys to change state.

OK key to return to menu 2

Escape key back to menu 2

MENU returns to menu 5.

menu 16

Left and right keys to move the cursor,

OK key to return to menu 2

menu 17

Left and right keys to move the cursor, up and down keys to select

OK key to return to menu 2

Escape key back to menu 2

MENU returns to menu 5.

channel size parameter calculation method reference

The maximum channel capacity of the system can be calculated using the following formula:

Rmax=6.75 x b x FEC x (188/204) x (1/(1+GD)) x (BW/8)

Rmax: The maximum capacity of the channel(Mb/s)

B: Coupling wave ratio function, QPSK orab=2, 16QAM orab=4，64QAMorab=6

FEC: internal error correction code rate(1/2, 2/3, 3/4, 5/6, 7/8)

GD: intervallo di guardia1/4, 1/8, 1/16, 1/32

BW: Bandwidth in M

According to the above formula, the maximum capacity of the channel can be calculated under a few parameters. The following table shows the information capacity under 8M bandwidth. The system will automatically calculate the size of the encoded output stream according to the set channel parameters so that the size of the output stream is not greater than the maximum capacity of the channel.

Nota

On the L25 position on the board (on the side of U13, the position is empty when leaving the factory) UN 0603 inductance can be added to increase the output power. The added inductance value can refer to in the figure below.

Precautions for order customization

1. FDD, as a transparent transmission module of peer-to-peer network with network port RJ45. It comes with two COFDM modules with different frequencies. The default frequency is 340Mhz and 590Mhz, customers can modify it through the parameter configuration board.
2. According to the default frequency of 340Mhz and 590MHz, the delivered accessories will contain the antenna of the default frequency. If you want to modify the frequency yourself, please let us know if we need to provide an antenna for the matching frequency.
3. With the parameter adjust menu board and screen, your client needs one to modify the parameter.
   When the parameters are adjusted well, they can be taken down. Except for your order quantity, please tell me how many pcs of the menu board and screen you need.

voice over ip radio system передатчик вай фай

Posta relativa

1. Mini_COFDM Ethernet module communication control protocol Vcan1886
2. How to calculate SNR and RSSI on your radio link? I want to get more parameters for my application.