Troubleshooting VCAN1746 Configuration and CVBS Issues

Troubleshooting VCAN1746 Configuration and CVBS Input Issues

In recent field deployments of the VCAN1746 video transmission cards, several customers have reported technical problems affecting configuration storage and CVBS input stability. After reviewing the details and consulting with our engineering team, we have summarized the findings below to help other users diagnose similar issues.

1. Configuration Save Failure — Potential SPI Flash Damage

Some users have observed that configuration changes—such as compression type or port settings—cannot be saved through the web interface. Although the UI loads normally and allows parameter modification, the settings revert to their previous values after rebooting the device.

Our engineers have confirmed that these symptoms are consistent with a known SPI Flash failure, specifically involving early batches that used a Winbond flash chip. In these cases, the flash becomes non-erasable, preventing any new data from being written.

To verify whether a card is affected, we advise users to:

  • Check the back side of the board
  • Photograph the flash chip used on the PCB
  • Confirm whether it is the early Winbond model or the updated replacement

This issue is purely hardware-related and is not caused by firmware or configuration behavior.

flash chip of av cvbs to ip ethernet video converter board
flash chip of av cvbs to ip ethernet video converter board

Please take a clear photo of the marking on the chip indicated by the arrow. The early batches used a Winbond flash chip, and some major customers reported this exact issue. Since the problem is caused by a hardware failure of the flash chip (not a software issue), we had to switch to a different flash model. したがって, we need to confirm which flash chip version is used on the customer’s faulty board.

2. CVBS Input Stops After 15–20 Minutes — Possible Thermal or Flash-Related Issue

Some deployments have shown that the CVBS input works normally on startup and the device begins transmitting Ethernet packets. しかし, after approximately 15–20 minutes of operation, the card either stops receiving CVBS input or stops sending Ethernet packets entirely. All indicator LEDs also stop functioning.

A quick restart restores operation, but the system fails again within a few minutes. After allowing the board to cool for about an hour, the normal 15–20 minute operation window returns.

Our engineers recommend the following steps to help diagnose the issue:

  • Access the encoder’s ウェブインターフェース after the issue occurs
  • Check the Video page and take a screenshot of the current video-input detection statusAccess the encoder web interface and check the Video page and current video-input detection status
  • Record a short video showing the status LEDs on the board during operation

These materials will help the engineering team analyze the behavior more accurately and determine whether it is related to hardware, thermal conditions, or other factors.

Next Steps

We continue to work closely with customers to identify affected units. If you have encountered similar symptoms, 私たちがお勧めします:

  • Checking the hardware revision of your VCAN1746 boards
  • Sending us photos of the flash chip for verification
  • Reporting the runtime behavior, video-input status, and LED status when the failure occurs

Our team is committed to improving product reliability and supporting customers with any field issues that arise.

Clients’ feedback

右, so the second issue is not related to SPI. I have performed the tests which u ask me but unfortunately I was not able to capture video. However i m sharing the test finding with u. When the problem occurs and the video gets stuck, both the input AV status LED and NET status LED are still blinking. I go to the web UI and checked video tab and it shows pal. So by this, i got the idea that the ivcan card is still decoding pal video as well as output Ethernet. So there might be some impedence mismatch or termination problem between video camera and ivcan1746 AV input end. I place a 220uF capacitor in series between AV signal line of ivcan1746 card and pal video camera. It resolves the stuck video issue however it degrade the quality of the video. Can u tell me the name of the video decoder chip and schematics of related circuitary if possible.

CVBS to Ethernet video encoder board schematic

Vcan1746_schematicsダウンロード

よくある質問

Q: Is the SPI flash used only once at startup to load configuration into the controller, or does the controller continue to access it during operation?

A: The system divides the SPI flash into 読み取り専用 (RO) そして Read-Write (RW) partitions. Configuration files are stored in the RW partition.
During system operation, the controller continuously accesses the configuration files in the RW partition.
When configuration changes are made, the system performs erase and write operations on the corresponding flash sectors, similar to how a Windows system writes to a hard drive.
Read operations do ない trigger erasure or writing, and therefore do ない affect the lifespan of the flash chip.
要約すれば, the SPI flash is actively used both at startup and during configuration updates, but normal read operations are safe and do not degrade the flash memory.

Q: When the issue occurs and the video freezes, what does the decoder side display— a completely black screen or something else?

A: If the decoder shows a black screen, this is expected behavior. When the CVBS interface chip loses the input signal, it automatically outputs a full-black video frame. This is the default behavior of the CVBS interface chip.
これが起こったとき, you may also observe the following symptoms:
The Web UI video tab displays “PAL”
The encoder AV status LED そして NET LED continue blinking (indicating the system is still running)
The video remains frozen or black
These signs indicate that the encoder’s CVBS interface chip is not detecting a valid video signal from the customer’s CVBS camera.

The root cause is likely between the customer’s CVBS camera そして encoder board’s CVBS interface chip — specifically that the encoder board is not recognizing the signal from the camera.

エンコーダモジュールボード

デコーダモジュールボード

カスタマイズ可能

新しいエンコーダ製品

いいえ. 製品名 Configuration 主な特長 状態
1 デュアルチャンネル USB UVC 可視光ビデオ エンコーダ 2× USB入力 デュアルUSBカメラビデオエンコーディングをサポート, およびRTSPストリーミング; ローカルCVBS/HDMI出力; 切り替え可能な表示モード Mass Production
2 デュアルチャンネルエンコーダー (1× USB可視光 + 1× USB Thermal Imaging camera) 2× USB入力 デュアルUSBカメラをサポート (見える + 熱) 捕獲, エンコーディング, およびRTSPストリーミング; ローカルCVBS/HDMI出力; 切り替え可能な表示モード Mass Production
3 RTSP デコーダ HDMI/CVBS ディスプレイ モジュール HDMI + CVBS出力 最大 4×1080P@30fps の RTSP ストリーム デコードをサポート; ビデオストリーミングプロトコル転送をサポート; HDMI/CVBS output display サンプルあり
4 RTSP デコーダ HDMI/CVBS ディスプレイ モジュール 4.3"/5" 液晶 HDMI出力 + 液晶画面 最大 4×1080P@30fps の RTSP ストリーム デコードをサポート; プロトコル転送; HDMI/CVBS output display デバッグ
5 デュアルチャンネルエンコーダー (1× USB可視光 + 1× CVBSアナログ) 1× CVBS + 1× USB UVC入力 デュアルビデオ (USB + CVBS), エンコードとRTSPストリーミング; ローカルCVBS/HDMI出力; 切り替え可能な表示モード デバッグ
6 デュアルチャンネルエンコーダー (1× USB UVC + 1× AHDアナログ) 1× AHD + 1× USB UVC入力 デュアルビデオキャプチャ (USB + AHD), エンコードとRTSPストリーミング; ローカルCVBS/HDMI出力; 切り替え可能な表示モード デバッグ
7 デュアルチャンネルエンコーダー (1× CVBS + 1× AHDアナログビデオ) CVBS + AHD 2 ビデオ入力 デュアルアナログビデオキャプチャ, エンコードとRTSPストリーミング; ローカルCVBS/HDMI出力; 切り替え可能な表示モード デバッグ
8 デュアルチャンネルエンコーダー (1× CMOSカメラ + 1× USB Thermal Imaging camera) 1× USBインターフェース CMOSをサポート + USBサーマルカメラキャプチャ, エンコードとRTSPストリーミング; ローカルCVBS/HDMI出力; 切り替え可能な表示モード Mass Production

For customized video input/output conversion solutions not listed in our products, OEM/ODMサポートについてはお問い合わせください. お客様のご要望に合わせた製品の開発が可能です.

質問する

← 戻る

ご回答をありがとうございました。 ✨