how to adjust LO frequency to control IF output frequency

часто задаються: Can the LO frequency of the downconverter be modified (напр., від 1750 МГц до 875 МГц або 750 МГц)?

Q: Привіт, can the down converters we bought from you be modified to cut the LO frequency in half? They currently operate at 1750 MHz—can they work around 875 MHz or be set to 750 МГц?

A: Так, the LO (Гетеродин) frequency can be modified. проте, we strongly recommend that the modification be carried out by our engineers, or that you return the unit to us for adjustment to ensure optimal performance and stability.

If you prefer to modify it yourself, it is also possible by following the procedure below.

---

🔧 Self-Modification Guide

1. Hardware Setup

• Open the metal enclosure of the FDC (Перетворювач частоти).
• Connect the device to your computer using a USB-to-TTL adapter.

Wiring (3 connections only):

• TX → RX
• RX → TX
• GND → GND

You may also make the cable yourself if needed.

---

2. Software Control via Serial Port

Use a serial terminal tool to send commands to the module.

---

3. Check Current Status

Команда:

check?

опис:

• Returns the current operating status and detected frequency values.

важливо:

• The command must end with a question mark (?), otherwise it will be invalid.

---

4. Modify LO Frequency

You can adjust the LO frequency by sending the following commands:

Target_FRE1=XXXX;
Target_FRE2=XXXX;
Target_FRE3=XXXX;

Пояснення:

• XXXX = desired frequency value (одиниця: МГц)
• Each command corresponds to a specific LO module (LE1 / LE2 / LE3)
• The system will automatically relock to the new frequency after setting

Приклади:

• Set LO to 875 МГц:

Target_FRE1=875;

• Set LO to 750 МГц:

Target_FRE1=750;

важливо:

• Each command must end with a semicolon (;), otherwise it will be invalid.

---

⚠️ Important Notes

• Ensure the target LO frequency is within the supported operating range of the hardware.
• Changing the LO may affect IF output frequency and system performance.
• Improper configuration may lead to signal instability or loss of lock.

---

✅ Recommendation

For best results and to avoid potential issues, we recommend:

• Contacting our engineering team for guidance, або
• Returning the unit to us for professional modification and calibration

---

If you have any questions or need the configuration software, feel free to contact us.

часто задаються

If you need to adjust the LO (гетеродин) range of the downconverter, you must first remove the bottom screws and open the top cover of the downconverter. Only then will you be able to access the internal connector and plug in the USB-to-UART adapter.

Q: What are TX and RX? I cannot find them on the converter.

A: TX and RX are standard UART communication signals:

• TX (Передавати): data output from the device
• RX (Отримати): data input to the device

They are not separate modules; they are already labeled on the interface pins of the converter.

Q: What pins are available on the connector?

A: The connector has four pins:

• GND – Ground
• TX – Transmit
• RX – Receive
• 3.3V – Power supply (NOT 5V)

Q: How should I wire it correctly?

A: Please connect as follows:

• GND → GND
• TX → RX (cross connection)
• RX → TX (cross connection)
• 3.3V → Power supply input (from USB-to-UART adapter or regulated 3.3V source)

⚠️ Important: TX and RX must be crossed; інакше, communication will not work.

Q: Can I use 5V power?

A: ❌ No, 5V is not allowed.
✔ Only 3.3V блок живлення is supported.

Using 5V will damage or burn out the downconverter.

Q: Can I power it via USB?

A: Так. If your USB-to-UART adapter provides a stable 3.3V вихід, ви можете:

• Use USB 3.3V to power the downconverter
• Connect TX / RX / GND for communication

Q: Software usage

A: After correct wiring, ви можете використовувати SSCOM software до:

• Open the serial port
• Communicate with the device
• Adjust the local oscillator (LO) frequency and other parameters

Important safety notes ⚠️

• Ensure the connector is inserted in the correct orientation
• Do NOT plug it in backwards
• Do NOT use 5V power
• Incorrect wiring may permanently damage the downconverter