Question 1

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 2

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

IP mesh wireless video data audio link module TDD transceiver wireless video transmitter

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 3

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Ethernet Radio Transceiver module with power control for external PA

Question 4

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

15-150km long-range wireless video transmitter and receiver for drone camera

Question 5

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 6

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 7

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 8

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 9

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 10

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 11

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

Question 12

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 13

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 14

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Question 15

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

Question 16

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 17

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 18

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 19

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 20

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 21

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 22

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

Question 23

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 24

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 25

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Question 26

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

Question 27

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 28

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 29

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 30

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 31

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 32

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 33

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

باند فرکانس	2.4گیگاهرتز(1مگابیت در ثانیه)	1.4گیگاهرتز(1مگابیت در ثانیه)	800مگاهرتز(1مگابیت در ثانیه)
20مگاهرتز پهنای باند	-99DBM به	/	/
10مگاهرتز پهنای باند	-102DBM به	-103DBM به	-103DBM به
5مگاهرتز پهنای باند	-104DBM به	-106DBM به	-106DBM به
3مگاهرتز پهنای باند	-106DBM به	-108DBM به	-108DBM به

فیلم با کیفیت بالا از دوربین های نقطه دید	فیلم با کیفیت بالا از دوربین های نقطه دید, DC در:7درجه فاصله اختیاری
درجه فاصله اختیاری	4کانکتور PIN ZH1.5mm
درجه فاصله اختیاری	درجه فاصله اختیاری
داده‌ها 1	3کانکتور PIN ZH1.5mm, TTL 3.3V
داده uart2 و uart3	6کانکتور PIN PH1.25mm, uart3 به عنوان uart کنترل و data uart کار می کند, TTL 3.3V
ورودی و خروجی صدا	4کانکتور PIN PH1.25mm
یو اس بی	کانکتور Micro USB, برای ارتقاء نرم افزار
تعویض	سیگنال کنترل TX/Rx برای تقویت کننده قدرت خارجی
آنتن اصلی	پورت آنتن TX/Rx, IPEX
آنتن دوم	درجه فاصله اختیاری, IPEX
12V بیرون	خروجی 12 ولت داخلی(<150میلی آمپر), برای منبع تغذیه فن خنک
چراغ برق	سرخ, چراغ روشن با برق معمولی
گره LED	آبی, هنگامی که ماژول فرستنده گیرنده به عنوان یک گره گیرنده کار می کند، چراغ روشن می شود; هنگامی که ماژول فرستنده گیرنده به عنوان یک گره فرستنده کار می کند چشمک بزنید
لینک LED	چراغ خاموش - نشان می دهد که گره به شبکه بی سیم متصل نیست; چراغ قرمز - نشان می دهد که گره متصل است, اما سیگنال بی سیم ضعیف است; نور نارنجی - نشان می دهد که گره به هم مرتبط است, سیگنال بی سیم وسط است; چراغ سبز - نشان می دهد که گره متصل است, سیگنال بی سیم قوی است.

پین	علامت	شرح
ورودی صدا	به صورت پیش فرض خط وارد کنید(Mic-in را مشخص کنید)	صدا به ماژول کنترل از راه دور بی سیم هدف ارسال می شود.
خروجی صدا	خط بیرون, درایو هدفون	هنگامی که گره داده های صوتی را از یک ماژول بی سیم از راه دور دریافت می کند, صدا روی این پین پخش خواهد شد.
GND	GND	GND
کنترل	نرم افزاری تعریف شده است	کنترل سوئیچ روشن/خاموش ورودی صدا

کار باند فرکانس	1428~ 1448 مگاهرتز یا 802 826 مگاهرتز
پهنای باند کانال	1.4مگاهرتز / 3 مگاهرتز / 5 مگاهرتز / 10 مگاهرتز / 20 مگاهرتز
روش مدولاسیون	QPSK / QAM16 / QAM64
انتقال قدرت	300میلی وات, 2W, 5W
حالت شبکه	نقطه به نقطه, شبکه ستاره نقطه به چند نقطه
انتقال از راه دور	هوا و زمین 15 کیلومتر است, 30کیلومتر, 50کیلومتر, 80کیلومتر, 100کیلومتر
رابط داده	2 پورت شبکه + 1 درگاه سریال
سرعت انتقال بی سیم	حداکثر 25 مگابیت در ثانیه, به اشتراک گذاشته شده توسط همه گره ها در انتقال دو طرفه.
رابط آنتن	2 اتصالات SMA
منبع تغذیه	7V~30V (12 ~ 28 ولت توصیه می شود)
اندازه	1025221.5میلی متر (فقط PCBA)
وزن	127 گرم

27کیلومتر 110کیلومتر NLOS پرسش و پاسخ

پرطرفدارترین HDMI تأخیر بسیار کم پرسش و پاسخ

ماژول انتقال ویدیوی بی سیم

صفحه ماژول FPV TX RX

CVBS به صفحه رمزگذار ویدیویی IP

ماژول لینک رادیویی بی سیم

صفحه رمزگذار HDMI به IP

ماژول فرستنده گیرنده بی سیم برای داده های ویدئویی پیوند کنترل فرستنده و گیرنده دو طرفه فرستنده-گیرنده

دو طرفه انتقال بی سیم داده های دیجیتال ماژول پیوند ویدئویی DLB

ویژگی

حساسیت

رابط معرفی می کند

مشخصات

سوالات متداول

TX900

هنوز یه سوال دارم?

سوالات متداول بیشتر

پست نسبی

بررسی

اولین کسی باشید که نقد می نویسید "ماژول فرستنده گیرنده بی سیم برای داده های ویدئویی پیوند کنترل فرستنده و گیرنده دو طرفه فرستنده-گیرنده”

از پاسخ شما سپاسگزاریم. ✨

از پاسخ شما سپاسگزاریم. ✨

27کیلومتر 110کیلومتر NLOS پرسش و پاسخ

پرطرفدارترین HDMI تأخیر بسیار کم پرسش و پاسخ

ماژول انتقال ویدیوی بی سیم

صفحه ماژول FPV TX RX

CVBS به صفحه رمزگذار ویدیویی IP

ماژول لینک رادیویی بی سیم

صفحه رمزگذار HDMI به IP

ماژول فرستنده گیرنده بی سیم برای داده های ویدئویی پیوند کنترل فرستنده و گیرنده دو طرفه فرستنده-گیرنده

دو طرفه انتقال بی سیم داده های دیجیتال ماژول پیوند ویدئویی DLB

ویژگی

حساسیت

رابط معرفی می کند

مشخصات

سوالات متداول

TX900

هنوز یه سوال دارم?

سوالات متداول بیشتر

پست نسبی

بررسی

اولین کسی باشید که نقد می نویسید "ماژول فرستنده گیرنده بی سیم برای داده های ویدئویی پیوند کنترل فرستنده و گیرنده دو طرفه فرستنده-گیرنده”

از پاسخ شما سپاسگزاریم. ✨

محصولات مرتبط