Question 1

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 2

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

IP mesh wireless video data audio link module TDD transceiver wireless video transmitter

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 3

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Ethernet Radio Transceiver module with power control for external PA

Question 4

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

15-150km long-range wireless video transmitter and receiver for drone camera

Question 5

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 6

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 7

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 8

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 9

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 10

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 11

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

Question 12

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 13

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 14

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Question 15

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

Question 16

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 17

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 18

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 19

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 20

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 21

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 22

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

Question 23

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 24

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 25

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Question 26

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

Question 27

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 28

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 29

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 30

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 31

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 32

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 33

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

Pasmo częstotliwości	2.4GHz(1Mbps)	1.4GHz(1Mbps)	800MHz(1Mbps)
20MHz Przepustowość	-99dBm	/	/
10MHz Przepustowość	-102dBm	-103dBm	-103dBm
5MHz Przepustowość	-104dBm	-106dBm	-106dBm
3MHz Przepustowość	-106dBm	-108dBm	-108dBm

Można wybrać tylko jedno wejście HDMI i SDI	Można wybrać tylko jedno wejście HDMI i SDI, wejście prądu stałego:7opcjonalna klasa odległości
opcjonalna klasa odległości	4Złącze PIN ZH1.5mm
opcjonalna klasa odległości	opcjonalna klasa odległości
Dane uart1	3Złącze PIN ZH1.5mm, TTL 3,3 V
Dane uart2 i uart3	6Złącze pinowe PH1,25mm, uart3 działa jako uart kontrolny i uart danych, TTL 3,3 V
Wejście i wyjście audio	4Złącze pinowe PH1,25mm
USB	Złącze microUSB, do aktualizacji oprogramowania
Przełącznik	Sygnał sterujący TX/Rx dla zewnętrznego wzmacniacza mocy
Antena główna	Port anteny TX/Rx, IPEX
Druga antena	opcjonalna klasa odległości, IPEX
12wyjście V	Wbudowane wyjście 12 V(<150mA), do zasilania fajnego wentylatora
Dioda zasilania	Czerwony, światło przy normalnym zasilaniu
Dioda węzła	Niebieski, świeci się, gdy moduł nadawczo-odbiorczy pracuje jako węzeł odbiorczy; Miga, gdy moduł nadawczo-odbiorczy pracuje jako węzeł nadawczy
Dioda łącza	Świeci się – wskazuje, że węzeł nie jest połączony z siecią bezprzewodową; Czerwone światło – wskazuje, że węzeł jest połączony, ale sygnał bezprzewodowy jest słaby; Światło pomarańczowe – wskazuje, że węzeł jest połączony, sygnał bezprzewodowy jest średni; Zielone światło – wskazuje, że węzeł jest połączony, sygnał bezprzewodowy jest silny.

KOŁEK	Sygnał	Opis
Wejście audio	Włącz domyślnie(Określ wejście mikrofonowe)	Dźwięk zostanie wysłany do docelowego bezprzewodowego modułu zdalnego.
Wyjście dzwięku	Zakreślać, prowadzić słuchawki	Gdy węzeł odbiera dane audio ze zdalnego modułu bezprzewodowego, dźwięk będzie odtwarzany na tym kodzie PIN.
GND	GND	GND
Kontrola	Zdefiniowane programowo	Sterowanie włącznikiem/wyłącznikiem wejścia audio

Praca pasmo częstotliwości	1428~1448MHz lub 802~826MHz
szerokość kanału	1.4MHz/3 MHz/5 MHz/10 MHz/20 MHz
metoda modulacji	QPSK / QAM16 / QAM64
moc nadawania	300mW, 2W, 5W
Tryb sieci	punkt-punkt, sieć gwiazdowa typu punkt-wielopunkt
odległość transmisji	powietrze-ziemia 15km, 30km, 50km, 80km, 100km
interfejs danych	2 porty sieciowe + 1 Port szeregowy
Szybkość transmisji bezprzewodowej	maksymalnie 25Mbps, współdzielone przez wszystkie węzły w transmisji dwukierunkowej.
interfejs anteny	2 Złącza SMA
Zasilacz	7V~30 V (zalecane 12 ~ 28 V)
Rozmiar	1025221.5mm (Tylko PCBA)
Waga	127 gramy

27km 110km NLOS FAQ

najgorętszy HDMI bardzo małe opóźnienie FAQ

Bezprzewodowy moduł transmisji wideo

Płyta modułu FPV TX RX

CVBS do IP Video Encoder Board

Bezprzewodowy moduł łącza radiowego

HDMI do płyty enkodera IP

Bezprzewodowy moduł nadawczo-odbiorczy do transmisji danych wideo RC Link dwukierunkowy nadajnik-odbiornik Nadajnik-odbiornik

Dwukierunkowa Bezprzewodowa transmisja cyfrowa moduł łącza wideo DLB

Cecha

Wrażliwość

Interfejs ten definiuje

Specyfikacja

Często zadawane pytania

TX900

Nadal masz pytanie?

Więcej często zadawanych pytań

Post względny

Opinie

Bądź pierwszą osobą, która napisze recenzję "Bezprzewodowy moduł nadawczo-odbiorczy do transmisji danych wideo RC Link dwukierunkowy nadajnik-odbiornik Nadajnik-odbiornik”

Twoja wiadomość została wysłana

Twoja wiadomość została wysłana

27km 110km NLOS FAQ

najgorętszy HDMI bardzo małe opóźnienie FAQ

Bezprzewodowy moduł transmisji wideo

Płyta modułu FPV TX RX

CVBS do IP Video Encoder Board

Bezprzewodowy moduł łącza radiowego

HDMI do płyty enkodera IP

Bezprzewodowy moduł nadawczo-odbiorczy do transmisji danych wideo RC Link dwukierunkowy nadajnik-odbiornik Nadajnik-odbiornik

Dwukierunkowa Bezprzewodowa transmisja cyfrowa moduł łącza wideo DLB

Cecha

Wrażliwość

Interfejs ten definiuje

Specyfikacja

Często zadawane pytania

TX900

Nadal masz pytanie?

Więcej często zadawanych pytań

Post względny

Opinie

Bądź pierwszą osobą, która napisze recenzję "Bezprzewodowy moduł nadawczo-odbiorczy do transmisji danych wideo RC Link dwukierunkowy nadajnik-odbiornik Nadajnik-odbiornik”

Twoja wiadomość została wysłana

Produkty powiązane