فرمان UART AT برای فرستنده و گیرنده ویدیوی بی سیم
فهرست مطالب
Suitable for the below model
-
دو طرفه پهپاد بی سیم ویدئو داده RC ماژول کنترل فرستنده و گیرنده دو طرفه برد بلند فرستنده-گیرنده Vcan1681 -
22کیلومتر 55 کیلومتر 80 کیلومتر 100 کیلومتر 150 کیلومتر فرستنده ویدیوی بی سیم فرستنده گیرنده انتقال گیرنده فرستنده و گیرنده PA 2W 5W 10W
-
10W PA 150KM پیوند داده تصویری هوابرد فرستنده فرستنده پهپاد دوربرد دستی تاکتیکی باند پهن
1. What is the UART AT commands?
UART (گیرنده/فرستنده ناهمزمان جهانی) is a serial communication protocol commonly used to connect microcontrollers and other devices to a computer. The AT commands are a set of commands used to communicate with a modem or any other device using AT commands over UART. These commands are usually used to configure the modem or to execute certain actions such as inquiry or modifying the parameter settings of the transmitter and receiver.
2. Why UART AT commands is a powerful tool?
UART AT commands are a powerful tool for creating customized automation solutions. UART stands for Universal Asynchronous Receiver/Transmitter and is a type of serial communication protocol. UART AT commands are used to control and configure UART devices, such as modems, transmitter-receivers, and other embedded systems.
UART AT commands are typically sent from a host computer to a UART device and are used to configure the device’s settings, such as baud rate, data format, and flow control. They can also be used to query the device’s status, such as its current location or signal strength. UART AT commands can also be used to send and receive data, such as text messages or transmitter-receiver current status.
UART AT commands are typically sent in ASCII format and are composed of a command string followed by a set of parameters. The command string is composed of an AT prefix followed by a command code, such as AT+CFG for configuring the device’s settings. The parameters are then used to specify the desired settings or data.
UART AT commands can be used to create customized automation solutions. مثلا, a UART device can be configured to send a text message when a certain condition is met, such as when a temperature threshold is exceeded. UART AT commands can also be used to control other devices, such as video input or outputs, H264 or H265 switch, or query data.
UART AT commands are a powerful tool for creating customized automation solutions. By sending the appropriate commands to a UART device, it is possible to configure the device’s settings, query its status, and send and receive data. This makes it possible to create automated solutions that can respond to changing conditions and take action accordingly.
AT Command Manual
The AT Command may have a little different for different two-way wireless video data audio link module versions, this AT command document is a basic description of the AT command for your reference.
1 AT^DACS: Access to the State
| The Command | Possible response (س) |
| The AT ^ DACS = < n > | |
| The AT ^ DACS? | ^ DACS: < n >, < دولت > |
| The AT ^ DACS =? | ^DACS: (list of supported <n>س) |
The Description
The execution command is used to set the switch state of ^DACSI: <دولت> escalation, که
is turned off by default at the beginning of the startup. When the setting is turned on, the current state will be reported once. When the active report is opened, the access node shall report the indication of access status after successful access; After the central node starts successfully, it can be regarded as successful access. After determining the type of central node, the access status can be reported.
The query command is used to query the current escalation switch state and the current access state.
The test command is used to test whether the command is supported and to query the value range of the <n> پارامتر.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<n>: integer type, indicating the active escalation
switch status
0: خاموش
1: در
2: query the current information <دولت>: integer type, indicating the access status
0: not accessed
1: accessed
مثال
The AT ^ DACS = 1 < CR > < LF > < CR > < LF > ^ DACSI: 0 < CR > < LF > < CR > < LF > باشه < CR > < LF > < CR > < LF > ^ DACSI: 1 < CR > < LF > the AT ^ DACS?
< CR > < LF > < CR > < LF > ^ DACS: 1, 1 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DACS =?
< CR > < LF > < CR > < LF > ^ DACS: (0-1) < CR > < LF > < CR > < LF > باشه < CR > < LF >
2 AT ^ DRPC: Radio Parameter Configure
| The Command | Possible response (س) |
| The AT ^ DRPC = < freq >, < پهنای باند >, < قدرت > | |
| The AT ^ DRPC? | ^ DRPC: < freq >, < پهنای باند >, < قدرت > |
| The AT ^ DRPC =? | ^DRPC: (list of supported <freq>س), (list of supported <پهنای باند>س) |
The Description
Execute the command for parameter Settings in the access state and save to NVRAM. The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
باشه اسuججessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<freq>: integer type, indicating frequency point frequency, unit 100KHz, محدوده
(8060-8259,14279-14478,24015-24814) <پهنای باند>: integer type, indicating bandwidth
0:1.4متر
1:3 متر
2:5 متر
3:10 متر
4: 15م (پشتیبانی نمی شود)
5: 20م
<قدرت>: “عدد صحیح” نوع, represents the fixed power of the center node, unit dBm, range from “-40” به “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall prevail.
مثال
The AT ^ DRPC = 24415, 1, “27” < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DRPC?
< CR > < LF > < CR > < LF > ^ DRPC: 24415, 1, “27” < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DRPC =?
< CR > < LF > < CR > < LF > ^ DRPC: 15-24814178 (8060-8259142, 79-14478240, 50-18050), (0 به 5) < CR > < LF > < CR > < LF > باشه < CR > < LF >
3 AT^DRPS: Radio Parameter Store in NVRAM
| The Command | Possible response (س) |
| The AT ^ DRPS = < freq >, < پهنای باند >, < قدرت > | |
| The AT ^ DRPS? | ^ DRPS: < freq >, < پهنای باند >, < قدرت > |
| The AT ^ DRPS =? | ^DRPS: (list of supported <freq>س), (list of supported <پهنای باند>س) |
The Description
The execute command is used to save parameters to NVRAM, after saving power and restart to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
باشه اسuججessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<freq>: integer type, indicating frequency point frequency, unit 100KHz, محدوده
(8060-8259,14279-14478,24015-24814) <bandwidth>: integer type, indicating the bandwidth
0:1.4متر
1:3 متر
2:5 متر
3:10 متر
4: 15م (پشتیبانی نمی شود)
5: 20م
<قدرت>: “عدد صحیح” نوع, represents the fixed power of the center node, unit dBm, range from “-40” به “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall prevail.
مثال
The AT ^ DRPS = 24415, 1, “27” < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DRPS?
< CR > < LF > < CR > < LF > ^ DRPS: 24415, 1, “27” < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DRPS =?
< CR > < LF > < CR > < LF > ^ DRPS: 15-24814178 (8060-8259142, 79-14478240, 50-18050), (0 به 5) < CR > < LF > < CR > < LF > باشه < CR > < LF >
4 AT^DSSMTP: Set Slave Max Tx Power
| The Command | Possible response (س) |
| The AT ^ DSSMTP = < قدرت > | |
| The AT ^ DSSMTP? | ^ DSSMTP: < freq >, < پهنای باند >, < قدرت > |
| The AT ^ DSSMTP =? |
The Description
The execute command is used to save parameters to NVRAM, after saving power and restart to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
باشه اسuججessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<قدرت>: “عدد صحیح” نوع, from the maximum transmitted power of the node, unit dBm, range from “-40” به “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall be taken as the criterion.
مثال
The AT ^ DSSMTP = “- 10” < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DSSMTP?
< CR > < LF > < CR > < LF > “- 10” < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DSSMTP =?
< CR > < LF > < CR > < LF > باشه < CR > < LF >
5 AT ^ DRPR: Radio Parameter Report
| The Command | Possible response (س) |
| The AT ^ DRPR = < n > | |
| The AT ^ DRPR? | ^ DRPR: < n > |
| The AT ^ DRPR =? | ^DRPR: (list of supported <n>س) |
The Description
Execute the command to set the local wireless parameter report ^DRPRI:این < شاخص >, <
earfcn >, < cell_id >, < rssi >, < pathloss >, < RSRP >, < RSRQ >, < SNR >, < کوتاه >, <
tx_power >, < dl_throughput_total_tbs >, < ul_thrpughput_total_tbs >, < dlsch_tb_error_per >,
< the MCS >, < rb_num >, < wide_cqi >, <Dlsch_tb_error_per_total >,< Max_Snr>,< Min_Snr>,< dl_total_tbs_g_rnti > on and off by default.The switch is only valid if the local machine is used as the access node. There is no active escalation for the center node even if the switch is on. The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<n>: integer type, indicating the active escalation switch status 0: خاموش 1: در
2:Query current information <شاخص>: integer type, indicating port index no. 1: بندر 12: بندر
2<earfcn>: integer type, frequency information of measurement result <cell_id>: integer type, cell information of measurement result <rssi>: string type, RSSI measurement value,DBM به, format as “±value”(جز “0”)”-141″ به “-44”: RSSI measurements
“+32767”: invalid value <pathloss>: integer type, pathloss,dBm0 to 191: pathloss
32767: invalid value < RSRP >: string type, RSRP measurement value,DBM به, format as
“±value”(جز “0”)”-141″ به “-44”: RSRP measurement value
“+32767”: invalid value < RSRQ >: string type, RSRQ measurement value,DBM به, format as “±value”(جز “0”), the actual value needs to be divided by 10 processing “-196” به “-30”: RSRQ measurement value
“+32767”: invalid value < SNR >: string type,SNR measurement, format as “±value”(جز
“0”)
“-50” به “+50”: SNR measurement value
“+32767”: invalid value < فاصله >: integer type, distance from the opposite end node, در متر, value range [0, 5000]
< tx_power >: string type, transmitted power, DBM به, format “±value”(جز “0”) “-50” به “+50”: transmitted power
“+32767”: invalid value < dl_throughput_total_tbs >: integer type, downlink throughput information, the sum of TB size in escalation cycle, بایت, محدوده [0,12000000]
< ul_thrpughput_total_tbs >: integer type, upline throughput information, the sum of TB size in escalation cycle, بایت, محدوده [0,12000000]
< dlsch_tb_error_per >: integer type, report the percentage of error in the cycle, محدوده [0,100]
< MCS >: MCS, value range [0,29]
<rb_num>: number of RB, value range [6,100]
<wide_cqi>: broadband CQI, value range [1,15]
<dlsch_tb_error_per_total>: report the total error percentage after entering the connection state, محدوده [0,100]
< Max_Snr>: maximum SNR within 10000ms, value range [-40,40]
< Min_Snr>:10000ms minimum SNR, value range [-40,40]
<dl_total_tbs_g_rnti>: integer type, total_tbsize for multicast packets
مثال
The AT ^ DRPR = 1 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DRPR?
< CR > < LF > < CR > < LF > ^ DRPR: 1 < CR > < LF > < CR > < LF > باشه < CR > < LF > < CR > < LF > ^ DRPRI: 1100 16هفتم, “- 46”, 20, “60”, “195”, “0”, 4000, “- 36”,
10000000500000,10,15,3,15, 50, “+ 30”, “25”, 15000 < CR > < LF > < CR > < LF > ^ DRPRI:0 dec, 2100-106 “, 115, “100”, “194”, “+ 20, 4000,” – 36 “, 10000000500000,10,15,3,15, 50, “+
35″, “to 30”, 15000 < CR > < LF > the AT ^ DRPR =?
< CR > < LF > < CR > < LF > ^ DRPR: (0-1) < CR > < LF > < CR > < LF > باشه < CR > < LF >
6 AT^DAPR: Access Nodes radio Parameter Report
| The Command | Possible response (س) |
| The AT ^ DAPR = < n > | |
| The AT ^ DAPR? | ^ DAPR: < n > |
| The AT ^ DAPR =? | ^DAPR: (list of supported <n>س) |
The Description
Execute the command to set the wireless parameters of the central node to report the access node ^DAPRI: این < IPv6Address >, < the index >, < rssi >, < pathloss >, < RSRP >, < RSRQ >, < SNR >, < short >, < tx_power >, < dl_throughput_total_tbs >, < ul_throughput_total_tbs >, < dlsch_tb_error_per >, < dlsch_tb_error_per_total >, < Max_Snr >, < Min_Snr >, < dlThe on-off state of _total_tbs_g_rnti>, turned off by default at startup.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<n>: integer type, indicating the active escalation switch status 0: خاموش 1: در
< 2: query the current information IPv6 address > : string type, has the IP address of the access nodes, is made up of 16 Numbers (0-255), in between each group number. ‘ ‘no, format is: a1, a2, a3, a4, a5, a6, a7, a8.. A9 a10. A11. A12. A13. A14. A15. A16
<شاخص>: integer type, indicating port index no. 1: بندر 12: port 2<rssi>: string type, rssi measurement value,DBM به, format as “±value”(جز “0”)”-141″ به “-44”: rssi measurement value
“+32767”: invalid value <pathloss>: integer type, pathloss,dBm0 to 191: pathloss
32767: invalid value < RSRP >: string type, RSRP measurement value,DBM به, format as
“±value”(جز “0”)”-141″ به “-44”: RSRP measurement value
“+32767”: invalid value < RSRQ >: string type, RSRQ measurement value,DBM به, format as “±value”(جز “0”), the actual value needs to be divided by 10 processing “-196” به “-30”: RSRQ measurement value
“+32767”: invalid value < SNR >: string type,SNR measurement, format as “±value”(جز
“0”)
“-50” به “+50”: SNR measurement value
“+32767”: invalid value < فاصله >: integer type, distance from the opposite end node, در متر, value range [0, 5000]
< tx_power >:string type, transmitted power, DBM به, format “±value”(جز “0”) “-50” به “+50”: transmitted power
“+32767”: invalid value < dl_throughput_total_tbs >:integer type, downlink throughput information, sum of TB size in escalation cycle, بایت, محدوده [0,12000000]
< ul_thrpughput_total_tbs >: integer type, upline throughput information, sum of TB size in escalation cycle, بایت, محدوده [0,12000000]
< dlsch_tb_error_per >:integer type, report the percentage of error in the cycle, محدوده [0,100]
< MCS >: MCS, value range [0,29]
<rb_num>: number of RB, value range [6,100]
<wide_cqi>: broadband CQI, value range [1,15]
<dlsch_tb_error_per_total>: report the total error percentage after entering the connection state, محدوده [0,100]
< Max_Snr>: maximum SNR within 10000ms, value range [-40,40]
< Min_Snr>:10000ms minimum SNR, value range [-40,40]
<dl_total_tbs_g_rnti>: integer type, total_tbsize for multicast packets
مثال
The AT ^ DAPR = 1 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DAPR?
< CR > < LF > < CR > < LF > ^ DAPR: 1 < CR > < LF > < CR > < LF > باشه < CR > < LF > < CR > < LF > ^ DAPRI:”1.2.3.4.0.0.0.0.1.2.3.4.200.201.202.203″, 1, “- 46”, 20, “60”, “195”, “0”, 4000, “-
36″, 10000000500000,10,15,3,15, 50, “+ 30”, “25”, 16000 < CR > < LF > < CR > < LF > ^ DAPRI:”1.2.3.4.0.0.0.0.1.2.3.4.200.201.202.203″, 2, “106”, 115, “100”, “194”, “+ 20, 4000,” –
36 “, 10000000500000,10,15,3,15,50, “+ 35”, “to 30”, 16000 < CR > < LF > the AT ^ DAPR =?
< CR > < LF > < CR > < LF > ^ DAPR: (0-1) < CR > < LF > < CR > < LF > باشه < CR > < LF >
7 AT^DAOCNDI: Communication Network configuration
| The Command | Possible response (س) |
| The AT ^ DAOCNDI = < band_bitmap > | |
| The AT ^ DAOCNDI? | ^ DAOCNDI: < band_bitmap > |
| The AT ^ DAOCNDI =? |
The Description
The execution command is used to set the operating frequency information of the ad-hoc network communication equipment, and the setting is followed by power-on and power-on. The query command is used to query the operating frequency information of AD hoc network communication equipment.
The test command is used to test whether the command is supported.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<band_bitmap>: string type(without double quotes),in hexadecimal format, the rightmost bit is the least significant bit (LSB/bit0).
Bit0:800 m frequency band
Bit2:1.4 G band
Bit3:2.4 G band
مثال
AT^DAOCNDI=0D<CR><LF>// Set band as 800M/ 1.4G / 2.4جی <CR><LF>باشه<CR><LF> AT^DAOCNDI=01<CR><LF>// Set band as 800M<CR><LF>باشه<CR><LF>
The AT ^ DAOCNDI?< CR > < LF > < CR > < LF > ^ DAOCNDI: 0 د < CR > < LF > < CR > < LF >
باشه < CR > < LF > the AT ^ DAOCNDI =?
< CR > < LF > < CR > < LF > باشه < CR > < LF >
8 AT ^ DDTC: Device Type Configuration
| The Command | Possible response (س) |
| The AT ^ DDTC = < نوع > | |
| The AT ^ DDTC? | ^ DDTC: < نوع >, < working type > |
| The AT ^ DDTC =? | ^ DDTC: (the list of supported < نوع > س) |
The Description
The execute command is used to set the type of AD hoc network communication device, which needs to be set before (+CFUN=1) startup, and takes effect after +CFUN=1 startup.When the type of terminal working equipment is determined, actively report
^DDTCI:<نوع>,<working type>
The query command is used to query ad-hoc network communication device type information.
The test command is used to test whether the command is supported.
The Final result code
باشه اسuججessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<نوع>: integer type, indicating the device type
0: خودکار 1: center node
2: گره دسترسی <working type>: integer type, indicating the current actual working device type
0: خودکار
1: center node
2: گره دسترسی
مثال
The AT ^ DDTC = 0 < CR > < LF > < CR > < LF > باشه < CR > < LF >
The AT ^ DDTC?< CR > < LF > < CR > < LF > ^ DDTC: 0, 0 < CR > < LF > < CR > < LF > باشه < CR >
< LF >
< CR > < LF > ^ DDTCI: 0, 1 < CR > < LF > the AT ^ DDTC =?
< CR > < LF >
< CR > < LF > ^ DDTC: (2-0) < CR > < LF > < CR > < LF > باشه < CR > < LF >
9 AT^DAPI: Access Password ID of Auto Organized Communication
Network configuration
The Command Possible response (س)
| The AT ^ DAPI = < password_id > | |
| The AT ^ DAPI? | ^ DAPI: < password_id > |
| The AT ^ DAPI =? |
The Description
The Settings command is used to set the PASSWORD ID for the ad-hoc networking device. Power on again.
The query command is used to query the PASSWORD ID of the ad-hoc networking device. The test command is used to test whether the command is supported.
The Final result code
باشه اسuججessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<password_id>: string type, in HEX format, data supports up to 32 بایت ها (HEX string 64 characters)
مثال
The AT ^ fbfa DAPI = “30313233” < CR > < LF > < CR > < LF > باشه < CR > < LF >
The AT ^ DAPI?< CR > < LF > < CR > < LF > ^ DAPI: “30313233 fbfa” < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DAPI =?
< CR > < LF > < CR > < LF > باشه < CR > < LF >
10 AT ^ DSTC: Set TDD configuration
| The Command | Possible response (س) |
| The AT ^ DSTC = < conf > | |
| The AT ^ DSTC? | ^ DSTC: < the conf > |
| The AT ^ DSTC =? | ^DSTC: (list of supported <conf>س) |
The Description
The execution command is used to set the parameters. After setting, the power down restarts to take effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<conf>: integer type, indicating TDD config setting
0: config0 (2D3U)
1: config1 (3D2U) (remote mode not supported)
2: پیکربندی 2 (4D1U) (remote mode not supported)
3: Config3 (1D4U)
مثال
The AT ^ DSTC = 0 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DSTC?
< CR > < LF > < CR > < LF > ^ DSTC: 0 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DSTC =?
< CR > < LF > < CR > < LF > ^ DSTC: (0-3) < CR > < LF > < CR > < LF > باشه < CR >
< LF >
11 AT^DPDBC: PS Data command Configuration
| The Command | Possible response (س) |
| The AT ^ DPDBC = < data_pri >, < dev_name > | |
| The AT ^ DPDBC =? | DPDBC: (range of support <data_pri>س), (range of support <dev_name>س) |
The Description
The execute command is used to set the data hosting priority to the transport port. The setting is valid before starting up.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<data_pri>: integer type, indicating the priority of data-bearing type, اعم از 1 به 3, the smaller the value, the higher the priority
<dev_name>: string type, which represents the transport port name
LMI40: LMI40 device, to be used by 0
LMI41: LMI41 device, to be used by 0
LMI43: LMI43 device, to be used by 1
LMI44: LMI44 device, to be used by 1
UAV_COMM: com-uart communication interface MEDIA0~ MEDAI15: public MEDIA data interface, in which MEDIA0~ MEDAI7 is for use by 0 and MEDIA7~ MEDAI15 is for use by 1
مثال
The AT ^ DPDBC = 1, “LMI40 < CR >”
< CR > < LF > باشه < CR > < LF > The AT ^ DPDBC =?این < CR >
< CR > < LF > ^ DPDBC: (1-3), (” LMI40 “, “LMI41”, “LMI43”, “LMI44”, “MEDIA0” ~ “MEDIA15”) < CR > < LF >
< CR > < LF > باشه < CR > < LF >
12 AT^DUBR: UART Baud Rate setting
| The Command | Possible response (س) |
| The AT ^ DUBR = < نرخ > | |
| The AT ^ DUBR? | ^ DUBR: < نرخ > |
| The AT ^ DUBR =? | DUBR: (list of supported <نرخ>س) |
The Description
The execution command is used to set the UART port baud rate parameter, after setting the power down reboot takes effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<نرخ>: integer type, represents the UART port baud rate parameter, and the value range is as follows:
1200:1200 بایت/ثانیه
2400:2400 بایت/ثانیه
4800:4800 بایت/ثانیه
9600:9600 بایت/ثانیه
19200:19200 بایت/ثانیه
28800:28800 بایت/ثانیه
38400:38400 بایت/ثانیه
57600:57600 بایت/ثانیه
115200:115200 بایت/ثانیه
مثال
The AT ^ DUBR = 57600 < CR >
< CR > < LF > باشه < CR > < LF >
The AT ^ DUBR?< CR > < LF > < CR > < LF > ^ DUBR: 57600 < CR > < LF > < CR > < LF > باشه < CR > < LF >
The AT ^ DUBR =?این < CR >
< CR > < LF > ^ DUBR: (1200240 0480 0960 0192 00288 00384 00576 00115 200) < CR > < LF >
< CR > < LF > باشه < CR > < LF >
13 AT^DCIAC: Ciphering and integrity arithmetic Configuration
| The Command | Possible response (س) |
| The AT ^ DCIAC = < arith > | |
| The AT ^ DCIAC? | ^ DCIAC: < arith > |
| The AT ^ DCIAC =? | ^DCIAC: (list of supported <arith>س) |
The Description
The execution command is used to set the encryption and insurance algorithm, after setting the power restart effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
باشه اسuججessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<arith>: integer type, represents the encryption and completion algorithm, the value range is as follows:
0: none ciphering and integrality
1: برف
2: the AES
3: ZUC
مثال
The AT ^ DCIAC = 2 < CR >
< CR > < LF > باشه < CR > < LF >
The AT ^ DCIAC?< CR > < LF > < CR > < LF > ^ DCIAC: 2 < CR > < LF > < CR > < LF > باشه < CR >
< LF >
The AT ^ DCIAC =?این < CR >
< CR > < LF > ^ DCIAC: (0-3) < CR > < LF >
< CR > < LF > باشه < CR > < LF >
14 AT ^ DFHC: Frequency Hopping Control
| The Command | Possible response (س) |
| The AT ^ DFHC = < n > | |
| The AT ^ DFHC? | ^ DFHC: < n > |
| The AT ^ DFHC =? | ^DFHC: (list of supported <n>س) |
The Description
The execution command is used to set the frequency hopping parameters. After setting, the power down restarts to take effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
باشه اسuججessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<n>: integer type, indicating the frequency hopping function setting 0: turn off the frequency hopping function
1: turn on the frequency hopping function
مثال
The AT ^ DFHC = 0 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DFHC?
< CR > < LF > < CR > < LF > ^ DFHC: 0 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DFHC =?
< CR > < LF > < CR > < LF > ^ DFHC: (0-1) < CR > < LF > < CR > < LF > باشه < CR > < LF >
15 AT ^ LCMFUN Set module functionality
| The Set command The AT ^ LCMFUN = < در > | Set command is used to Set module power on or off. The Response: OK If the error is related to ME functionality: + CME ERROR: 100 The Parameter: < در >: integer of power on or off 0: poweroff 1: poweron 2: poweroff-but not close electric on FLASH/DDR |
| The Read command The AT ^ LCMFUN? | The Response: این < در > OK The Parameter |
| See the set command | |
| The Test command The AT ^ LCMFUN =? | The Response: ^LCMFUN: (list of supported < در >س) OK The Parameter See the set command مثال ^ LCMFUN: (0, 2) باشه |
| The Reference | |
| توجه داشته باشید |
16 AT ^ POWERCTL Power Ctrl
| The Set Command The AT ^ POWERCTL = < value > | Set command is used to reboot OS The Response: OK If the error is related to ME functionality: + CME ERROR: 100 The Parameter: < value>: integer of the reboot OS,only one value 1 |
| The Test Command The AT ^ POWERCTL =? | The Response: POWERCTL: (list of supported< vlaue >) OK The Parameter See the set command Example ^ POWERCTL: 1 باشه |
The Description
The execute command is used to restart the module.
| The Response | The result |
| باشه | Successful |
| ERROR or +CME ERROR: <err> | The Command performing failed |
مثال
The AT ^ POWERCTL = 1 < CR > < LF > < CR > < LF > باشه < CR > < LF >
17 AT^DSSMTP: Set Slave Max Tx Power
| The Command | Possible response (س) |
| The AT ^ DSSMTP = < قدرت > | |
| The AT ^ DSSMTP? | ^ DSSMTP: < قدرت > |
| The AT ^ DSSMTP =? |
The Description
The execute command is used to save parameters to NVRAM, after saving in and out of flight to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<قدرت>: “عدد صحیح” نوع, from the maximum transmitted power of the node, unit dBm, range from “-40” به “40”, and if the setting exceeds the maximum supported by the terminal, the maximum supported by the terminal shall be taken as the criterion.
مثال
The AT ^ DSSMTP = “- 10” < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT
^ DSSMTP?
< CR > < LF > < CR > < LF > “- 10” < CR > < LF > < CR > < LF > باشه < CR > < LF >
the AT ^ DRPS =?
< CR > < LF > < CR > < LF > باشه < CR > < LF >
18 AT^DSONMCS: Modulation and Coding Scheme Index Set
| The Command | Possible response (س) |
| The AT ^ DSONMCS = < حالت >,, < Mcs > [] | |
| The AT ^ DSONMCS? | ^ DSONMCS: < حالت >, < the Mcs > |
| The AT ^ DSONMCS =? | DSONMCS: (list of supported <حالت>س),(list of supported <Mcs>س) |
The Description
Setting command is used to set MCS index value switch and index value, if not on, is not allowed to change the MCS value; If the MCS switch is turned on, the MCS index value is allowed to be set, effective immediately and saved to NVRAM for permanent effect. The default switch is off.
The query command queries the current set value.
The test command is used to test the Settings that the command supports. NOTE: this instruction can only be issued from the primary node
The Final result code
باشه هrry.error or +CME ERROR: <err>Command performing failed.
Defined values
<حالت>: integer type, which represents the function setting of MCS index value. به طور پیش فرض, the setting function is not turned on 0: the setting function is turned off
1: open the setting function
<Mcs>: integer type, indicating the Mcs index value, which ranges from 0 to 27.The default value is 27
مثال
The AT ^ DSONMCS = 1, 5 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DSONMCS?
< CR > < LF > < CR > < LF > ^ DSONMCS: 1, 5 < CR > < LF > < CR > < LF > باشه < CR > < LF > این
AT ^ DSONMCS =?
< CR > < LF >
< CR > < LF > ^ DSONMCS: (0-1), (0-27) < CR > < LF > < CR > < LF > باشه < CR > < LF >
19 AT ^ DLF: Lock Freq
| The Command | پossible response (س) |
| The AT ^ DLF = < lock_type > [, < freq >] | |
| The AT ^ DLF? | ^ DLF: < lock_type > [, < freq >] |
| The AT ^ DLF =? | ^DLF: (list of supported<;Lock_type>س), (list of supported lock <freq>س) |
The Description
The execution command is used to control the user to set the lock frequency information, the setting value is saved to NVRAM, and the in-and-out flight takes effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<LockType >: integer type, indicating that the user sets the lock specified frequency switch setting 0: unlocking or unlocking the frequency point
1: lock the specified frequency point
<Freq>: integer type, indicating frequency point frequency, unit 100KHz, محدوده
(8060-8259,14279-14478,24015-248140)
مثال
The AT ^ DLF = 1143 50 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DLF?
< CR > < LF > < CR > < LF > ^ DLF: 1, 14350 < CR > < LF > < CR > < LF > باشه < CR > < LF > این
AT ^ DLF =?
< CR > < LF > < CR > < LF > ^ DLF: (0-1), (8060-8259142
79-14478240-15-24814178-50-18050) < CR > < LF > < CR > < LF > باشه < CR > < LF >
20 AT^DSONSSF: Set Special Function For SON
| تیساعتe Command | پossible response (س) |
| The AT ^ DSONSSF = < FuncType > [, < ارزش >] | |
| The AT ^ DSONSSF? | ^ DSONSSF: < FuncType > [, < ارزش >] |
| The AT ^ DSONSSF =? | DSONSSF: (list of supported (<FuncType>س),(list of supported (<Values>س) |
The Description
The Settings command is used to select and/or set specific functions.AT^DSONSSF=<FuncType> is used to select a particular function, and the result of the selection can be used in the query command.AT^DSONSSF=<FuncType>, و <ارزش> is used to set the Value of a particular function.
The query command returns the current value of the selected function (set by
AT^DSONSSF=<FuncType>).If no function is selected, the default function is returned.
The test command returns the supported value.
The set parameters are stored in NVRAM and take effect on the next power-on.
The Final result code
Okerry.error or +CME ERROR: <err>Command performing failed.
Defined values
<FuncType >: integer type, identifying a specific function
0: send ACK packets in the normal order
1: access to external network
2: the DRX shut down
3. PING and low latency service optimization
4: low power mode
Other value reservation
< ارزش > : an integer type
0: not enabled (کنترل کنید)
1: enable (کنترل کنید)
مثال
The AT ^ DSONSSF = 0, 1 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DSONSSF?
< CR > < LF > < CR > < LF > ^ DSONSSF: 0, 1 < CR > < LF > < CR > < LF > باشه < CR > < LF > این
AT ^ DSONSSF =?
< CR > < LF > < CR > < LF > ^ DSONSSF: (0 به 4), (0-1) < CR > < LF > < CR > < LF > باشه < CR > < LF >
21 AT ^ DSONSBR: Sub Band Range
| The Command | Possible response (س) |
| The AT ^ DSONSBR = < باند >, < earfcn_start >, < earfcn_end > [, < باند >, < earfcn_start >, < earfcn_end > [, < باند >, < earfcn_start >, < earfcn_end >]…]. | |
| The AT ^ DSONSBR? | ^ DSONSBR: < باند >, < earfcn_start >, < earfcn_end > [, < باند >, < earfcn_start >, < earfcn_end > [, < باند >, < earfcn_start >, < earfcn_end >]…]. |
| The AT ^ DSONSBR =? | DSONSBR: <باند>,(list of supported <earfcn>س), |
<باند>,(list of supported <earfcn>س),…
The Description
The execute command is used to configure the frequency range of each subband, save to
NVRAM, and take effect in and out of flight.
The query command is used to query the current subband range configuration.
The test command is used to test whether the command is supported and the range of frequencies allowed to be configured for each subband.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<باند>: integer type, subband number
64: BAND64
65: BAND65
66: BAND66
<earfcn_start>: integer type, starting frequency, the value range is related to the subband, the value must not be greater than <earfcn_end>
BAND64:24015-24814
BAND65:8060-8259
BAND66:14279-14478
<earfcn_end>: integer type, end frequency point number, the value range is related to the subband, its value cannot be less than <earfcn_start>
BAND64:24015-24814
BAND65:8060-8259
BAND66:14279-14478
مثال
The AT ^ DSONSBR = 64240, 20248, 00,66,14280,14470 < CR > < LF > < CR > < LF > باشه < CR >
< LF > the AT ^ DSONSBR?
< CR > < LF > < CR > < LF > ^ DSONSBR: 64240, 20248, 00,66,14280,14470 < CR > < LF > < CR > < LF > باشه < CR > < LF > the AT ^ DSONSBR =?
< CR > < LF > < CR > < LF > ^ DSONSBR: 64, (24015-24814), 65, (8060-8259), 66,
(14279-14478), 67, (17850-18049), 68, (7580-8029), 69, (14470-14669) < CR > < LF > < CR >
< LF > باشه < CR > < LF >
22 AT ^ APSLEEP: AP SLEEP ENABLE
| The Command | پossible response (س) |
| The AT ^ APSLEEP = < n > | باشه |
| The AT ^ APSLEEP? | The Error |
| The AT ^ DACS =? | ^ APSLEEP: (list of supported <n>س) |
The Description
Execute the command to enable AP sleep. Turn on AP sleep by default.N value only supports
1, only supports AP sleep enable function.
Once the command is valid, the AP needs to issue the command again after being awakened to trigger the next sleep.
<n>=1, enabling ap to sleep
<n>= other value, invalid, error returned
The query command is not supported and an error is returned.
The test command is used to test whether the command is supported and to query the value range of the <n> پارامتر.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<n>: integer type to enable ap sleep 1: در
مثال
AT^ APSLEEP =1<CR><LF><CR><LF> باشه <CR><LF>AT^ APSLEEP?
< CR > < LF > < CR > < LF > + CME ERROR: 100 < CR > < LF > the AT ^ APSLEEP =?
< CR > < LF > < CR > < LF > ^ APSLEEP: (1) < CR > < LF >
سوال بپرسید
از پاسخ شما سپاسگزاریم. ✨