2 وات یا 5 وات یا 10 watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter TDD
This is a key part of a wireless video transmitter, which can enlarge the RF signal for a longer range and distance. اختیاری 1 وات, 2 وات, 5 وات, و 10 وات.
فهرست مطالب
Features
- باند فرکانس: 800Mhz-830Mhz, 1425MHz-1455MH
- RF در: 25± 2dBm
- برق خروجی RF: 2 وات (33DBM به)
- 1400Mhz Transmitter gains 11dB when used with a two-way wireless video data link module, set up the maximum RF power as 22~24 dBm, then the RF out power will be 33~35 dBm.
- 800Mhz Transmitter gain: 13دسی بل, when used with a two-way wireless video data link module, set up the maximum RF power as 20~22 dBm, then the RF out power will be 33~35 dBm.
- برق خروجی RF: 5 وات (37DBM به)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, set up the maximum RF power as 22~25 dBm, then the RF out power will be 37~37 dBm.
- 800Mhz Transmitter gain: 17دسی بل, when used with a two-way wireless video data link module, set up the maximum RF power as 20~22 dBm, then the RF out power will be 37~39 dBm.
- برق خروجی RF: 10 وات (40DBM به)
- افزایش TX: 18دسی بل, when used with a two-way wireless video data link module, set up the maximum RF power of as 22~24 dBm, then the RF out power will be 40~42 dBm.
- 2 Watts Power in DC12V~16V;
- 5 Watts Power in DC24V~25V, حداقل امتیاز جریان برق 1.8A@24V
- 10 Watts Power in DC24V~30V, حداقل امتیاز جریان برق 2.5A@28V
- 2 Watts Power consumption: <6W متوسط; 5 Watts Power consumption: <14W متوسط; 10 Watts Power consumption: <28میانگین W
- 2 وات 5 Watts PCBA size: 46.5*31میلی متر, ضخامت PCB: 1.2میلی متر
- 10 Watts Dimensions: 65*62*13.5میلی متر, بدون شامل کانکتور خارج از محفظه فلزی, وزن: 98g
- امپدانس: 50 اهم
Working together with a two-way wireless video data link Module:
ورودی RF
RF Output
| برق وارد کنید | We should solder two bonding pads to connect with power VDD and GND. |
| کنترل کنید | We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL و GND). ورودی بالاست (1.8V تا 3.3 ولت) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode. |
| RF در | IPEX connector for connection with the main antenna of the two-way wireless video data link module. |
| خروجی RF | We should solder the bonding pad to an antenna connector. |
مورد مسکن و مونتاژ
We recommend that this power amplifier for our two-way wireless video data link OEM PCBA module.
To enhance the power amplifier in conjunction with our two-way wireless video data link module, we recommend you fabricate a metallic housing casing that aligns with your device’s architecture.
It should also leave at least 6mm between the PA board and the upper cover. In order to facilitate heat dissipation and establish an electrical grounding connection, the back side of the PA board must be directly and firmly attached to the metal.
Proper integration of heat dissipation techniques, such as a heat sink or fan, is essential for optimal performance in designs utilizing the PA OEM module.
We can also make a metal chamber for this PA module according to the customer’s requirement.
The below model has a built-in Power Amplifier inside.
پرسش و پاسخ:
س: Could you tell me your RF power amplifier dimension size? I want to design my enclosure.
آ: لطفا تصویر زیر را بررسی کنید. And tell us if you need any further information.
س: Could you show me the real photos of your RF linear power amplifier?
آ: مطمئن, لطفا تصاویر زیر را بررسی کنید.
س: Are you not using the TQP7M9104 amplifier in the 2W module?
آ: خیر
بررسی ها
هنوز هیچ بررسی وجود ندارد.