2 Watt o 5 Watt o 10 watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter TDD
This is a key part of a wireless video transmitter, which can enlarge the RF signal for a longer range and distance. Opzionale 1 Watt, 2 Watt, 5 Watt, E 10 Watt.
Sommario
Caratteristiche
- Banda di frequenza: 800Mhz-830Mhz, 1425MHz-1455MH
- Ingresso RF: 25±2dBm
- Potenza in uscita RF: 2 Watt (33dBm)
- 1400Mhz Transmitter gains 11dB when used with a two-way wireless video data link module, set up the maximum RF power as 22~24 dBm, then the RF out power will be 33~35 dBm.
- 800Mhz Transmitter gain: 13dB, when used with a two-way wireless video data link module, set up the maximum RF power as 20~22 dBm, then the RF out power will be 33~35 dBm.
- Potenza in uscita RF: 5 Watt (37dBm)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, set up the maximum RF power as 22~25 dBm, then the RF out power will be 37~37 dBm.
- 800Mhz Transmitter gain: 17dB, when used with a two-way wireless video data link module, set up the maximum RF power as 20~22 dBm, then the RF out power will be 37~39 dBm.
- Potenza in uscita RF: 10 Watt (40dBm)
- Guadagno in trasmissione: 18dB, when used with a two-way wireless video data link module, set up the maximum RF power of as 22~24 dBm, then the RF out power will be 40~42 dBm.
- 2 Watts Power in DC12V~16V;
- 5 Watts Power in DC24V~25V, corrente nominale di alimentazione minima 1,8 A a 24 V
- 10 Watts Power in DC24V~30V, minimum 2.5A@28V power current rating
- 2 Watts Power consumption: <6W media; 5 Watts Power consumption: <14W media; 10 Watts Power consumption: <28W nella media
- 2 Watt 5 Watts PCBA size: 46.5*31mm, lo spessore del PCB: 1.2mm
- 10 Watts Dimensions: 65*62*13.5mm, not including the connector out of the metal housing, Peso: 98g
- Impedenza: 50 ohm
Working together with a two-way wireless video data link Module:
Ingresso RF
RF Output
| Power in | We should solder two bonding pads to connect with power VDD and GND. |
| Controllare | We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL e GND). L'ingresso è alto (1.8V a 3,3 V) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode. |
| Ingresso RF | IPEX connector for connection with the main antenna of the two-way wireless video data link module. |
| Uscita RF | We should solder the bonding pad to an antenna connector. |
Custodia e assemblaggio
We recommend that this power amplifier for our two-way wireless video data link OEM PCBA module.
To enhance the power amplifier in conjunction with our two-way wireless video data link module, we recommend you fabricate a metallic housing casing that aligns with your device’s architecture.
It should also leave at least 6mm between the PA board and the upper cover. In order to facilitate heat dissipation and establish an electrical grounding connection, the back side of the PA board must be directly and firmly attached to the metal.
Proper integration of heat dissipation techniques, such as a heat sink or fan, is essential for optimal performance in designs utilizing the PA OEM module.
We can also make a metal chamber for this PA module according to the customer’s requirement.
The below model has a built-in Power Amplifier inside.
FAQ:
Q: Could you tell me your RF power amplifier dimension size? I want to design my enclosure.
UN: Si prega di controllare l'immagine qui sotto. And tell us if you need any further information.
Q: Could you show me the real photos of your RF linear power amplifier?
UN: sure, please check the below pictures.
Q: Are you not using the TQP7M9104 amplifier in the 2W module?
UN: NO
Recensioni
Non ci sono ancora recensioni.