دستورالعمل تغییر پارامتر پیوند داده تله متری رادیویی

دستورالعمل تغییر پارامتر پیوند داده تله متری رادیویی VCAN1915

1. حالت پیکربندی را وارد کنید

اولین, برای یادگیری نحوه پیکربندی رادیو و کارکردهای دستورات مختلف به دفترچه راهنمای عملیات VCAN1915 مراجعه کنید. رادیو می تواند از طریق درگاه داده تشخیص را وارد کند, با استفاده از نرم افزار پورت سریال Hyperterminal یا SSCOM3.2. نرخ پورت سریال را بر روی نرخ رابط رادیویی فعلی تنظیم کنید, مانند 115200, وارد +++ ورود, و هیچ OK حامل به طور همزمان نمایش داده می شود تا نشان دهد که وارد شده اید, و سپس دستورات زیر را وارد کنید (هر فرمان با بازگشت کالسکه دنبال می شود):

configuration modes of Radio Telemetry Data Link Parameter modification instruction
حالت پیکربندی دستورالعمل اصلاح پارامتر پیوند داده تله متری رادیویی

قدرت در رادیو (لطفاً ابتدا آنتن را وصل کنید و رادیو را با یک کابل داده به پورت سریال رایانه وصل کنید), open the HyperTerminal or serial port software, set the baud rate to the same rate as the radio (مانند 115200 8 ن 1), in the software After entering +++ in the blank space (the entered +++ is not displayed), NO CARRIER OK is displayed, همانطور که در شکل نشان داده شده است:

Radio Telemetry Data Link Parameter modification instruction 1
Radio Telemetry Data Link Parameter modification instruction 2

پیکربندی را تغییر دهید

1. 400M تنظیم حالت فرکانس ثابت:

Enter the following command, and the prompt OK means correct, و [وارد کردن] یعنی بازگشت کالسکه:

  • ATS128=0[وارد کردن]—————————Change to 400M fixed frequency mode
  • AT&F51[وارد کردن]——————————Change to MH transparent transmission default configuration
  • ATS131=0[وارد کردن]—————————Change the transmit frequency
  • ATS132=0[وارد کردن]—————————Change the receiving frequency
  • ATS102=5[وارد کردن]—————————Change the interface rate
  • ATS103=7[وارد کردن]—————————Change air speed
  • ATP0=[وارد کردن], then enter deal%er to display Enter Channel Number (0 به 63), then enter 0[وارد کردن], then enter 459837500[وارد کردن], وارد 2[وارد کردن], then enter 2[وارد کردن], and finally press ESC to exit — —-Edit frequency table
  • AT&W[وارد کردن]——————————–صرفه جویی
  • ATA[وارد کردن]————————————خروج

توجه داشته باشید: The frequencies of the four selected channels S131, S132, S191 and S192 cannot be empty. مثلا, S191=2-000.000000 will not be saved at this time.

After setting up, the working frequency is 459.837500MHz, the interface rate is 19200, the air rate is 19200, and the protocol is MH transparent transmission mode for communication. If you need to change the PCC transparent transmission protocol, set AT&F53 and set a different address code (S105). Check the manual to set up AT&FXX in other modes.

The 400M fixed frequency mode can be directly configured using SDRCOM software. For instructions, please refer to the VCAN1915 operation manual.

2. 900تنظیم تنظیم حالت فرکانس M:

Enter the following command, and the prompt OK means correct, و [وارد کردن] یعنی بازگشت کالسکه:

        آ. Configure as main station (زمین):
  • ATS128=1[وارد کردن]—————————Change to 900M frequency hopping mode
  • AT&F1[وارد کردن]——————————-Change to point-to-multipoint master station
  • ATS102=1[وارد کردن]————————–Set the interface rate (1 نشان می دهد 115200)
  • ATS103=1[وارد کردن]—————————Set the air rate (1 نشان می دهد 115200)
  • ATS113=0[وارد کردن]—————————Cancel data retransmission
  • ATS104=XXXX[وارد کردن]———————-Set ID number
  • ATS109=10[وارد کردن]—————–Set the frequency hopping interval (10 represents 30ms, set as needed, default 20ms)
  • AT&W[وارد کردن]——————————–صرفه جویی
  • ATA[وارد کردن]————————————خروج
        ب. Configuration of component stations (مروارید):
  • ATS128=1[وارد کردن]—————————-Change to 900M frequency hopping mode
  • AT&F2[وارد کردن]—————————–Change to point-to-multipoint slave
  • ATS102=1[وارد کردن]—————————Set the interface rate (1 نشان می دهد 115200)
  • AtS103=1[وارد کردن]—————————Set the air rate (1 نشان می دهد 115200)
  • ATS113=0[وارد کردن]—————————Cancel data retransmission
  • ATS104=XXXX[وارد کردن]———————-Set ID number
  • ATS248=4[وارد کردن]—————————Set the reconnection interval
  • AT&W[وارد کردن]——————————–صرفه جویی
  • ATA[وارد کردن]————————————خروج

When there are multiple sub-stations, different address codes (S105) need to be set. بعد از تنظیم, the frequency band is 902-928MHz, the interface rate is 115200, and the air rate is 115200 for communication.

3. 400تنظیم تنظیم حالت فرکانس M

Enter the following command, and the prompt OK means correct, و [وارد کردن] یعنی بازگشت کالسکه:

        آ. Configure as main station (زمین):
  • ATS128=2[وارد کردن]—————————Change to 400M frequency hopping mode
  • AT&F1[وارد کردن]——————————-Change to point-to-multipoint master station
  • ATS102=1[وارد کردن]————————–Set the interface rate (1 نشان می دهد 115200)
  • ATS103=1[وارد کردن]—————————Set the air rate (1 نشان می دهد 115200)
  • ATS113=0[وارد کردن]—————————Cancel data retransmission
  • ATS104=XXXX[وارد کردن]———————-Set ID number
  • ATS109=10[وارد کردن]—————–Set the frequency hopping interval (10 represents 30ms, set as needed, default 20ms)
  • ATP0=[وارد کردن], click to open the file in SSCOM, select the frequency table file, and click to send the file
  • ATP1=[وارد کردن], click to open the file in SSCOM, select the frequency table file, and click to send the file
  • AT&W[وارد کردن]——————————–صرفه جویی
  • ATA[وارد کردن]————————————خروج
        ب. Configuration of component stations (مروارید):
  • ATS128=2[وارد کردن]—————————-Change to 400M frequency hopping mode
  • AT&F2[وارد کردن]—————————–Change to point-to-multipoint slave
  • ATS102=1[وارد کردن]—————————Set the interface rate (1 نشان می دهد 115200)
  • AtS103=1[وارد کردن]—————————Set the air rate (1 نشان می دهد 115200)
  • ATS113=0[وارد کردن]—————————Cancel data retransmission
  • ATS104=XXXX[وارد کردن]———————-Set ID number
  • ATS248=4[وارد کردن]—————————Set the reconnection interval
  • ATP0=[وارد کردن], click to open the file in SSCOM, select the frequency table file, and click to send the file
  • ATP1=[وارد کردن], click to open the file in SSCOM, select the frequency table file, and click to send the file
  • AT&W[وارد کردن]——————————–صرفه جویی
  • ATA[وارد کردن]————————————خروج

The frequency table file format is TXT, 50 نقاط فرکانس, based on the antenna coverage frequency.

Radio Telemetry Data Link Parameter modification instruction 3
Radio Telemetry Data Link Parameter modification instruction 4

When there are multiple sub-stations, different address codes (S105) need to be set. بعد از تنظیم, the frequency band is 419-421MHz, the interface rate is 115200, and the air rate is 115200 for communication.

4. 840تنظیم تنظیم حالت فرکانس M:

Enter the following command, and the prompt OK means correct, و [وارد کردن] یعنی بازگشت کالسکه:

        آ. Configure as main station (زمین)
  • AT&F1[وارد کردن]——————————-Change to point-to-multipoint master station
  • ATS102=1[وارد کردن]————————–Set the interface rate (1 نشان می دهد 115200)
  • ATS103=1[وارد کردن]—————————Set the air rate (1 نشان می دهد 115200)
  • ATS113=0[وارد کردن]—————————Cancel data retransmission
  • ATS104=XXXX[وارد کردن]———————-Set ID number
  • ATS109=10[وارد کردن]—————-Set the frequency hopping interval (10 represents 30ms, set as needed, default 20ms)
  • AT&W[وارد کردن]——————————–صرفه جویی
  • ATA[وارد کردن]————————————خروج

        ب. Configure component station (مروارید)

  • AT&F2[وارد کردن]—————————–Change to point-to-multipoint slave
  • ATS102=1[وارد کردن]—————————Set the interface rate (1 نشان می دهد 115200)
  • AtS103=1[وارد کردن]—————————Set the air rate (1 نشان می دهد 115200)
  • ATS113=0[وارد کردن]—————————Cancel data retransmission
  • ATS104=XXXX[وارد کردن]———————-Set ID number
  • ATS248=4[وارد کردن]—————————Set the reconnection interval
  • AT&W[وارد کردن]——————————–صرفه جویی
  • ATA[وارد کردن]————————————خروج

When there are multiple sub-stations, different address codes (S105) need to be set. بعد از تنظیم, the frequency band is 840-845MHz, the interface rate is 115200, and the air rate is 115200 for communication. The 840M frequency hopping frequency table settings are the same as the 400M frequency hopping settings.

توجه داشته باشید: 840M is a separate software version and cannot be changed to 400M and 900M frequency hopping.

  1. Other reference content

    1. TDMA mode

برای جزئیات, refer to the TDMA instructions in the VCAN1915 operation manual. If you need to change, add the following command. OK means correct, و [وارد کردن] یعنی بازگشت کالسکه. Taking one-to-three as an example, the slave address code is 2, 3, 4:

        Main station:

  • ATS244=1—————————————-Change to TDMA mode
  • ATS251=1—————————————-Set timeout configuration
  • ATT0=2————————————————–Edit slave station List, starting with station 2
  • ATT1=3d

2. 900M frequency limit

    After entering the configuration mode, you need to enter the following command to set the frequency band limit:

    AT&H0

Radio Telemetry Data Link Parameter modification instruction 5

    وارد 1 و Enter را فشار دهید

Radio Telemetry Data Link Parameter modification instruction 6

    وارد 902.400 و Enter را فشار دهید, then enter 907.500 و Enter را فشار دهید, and press ESC twice to exit.

Radio Telemetry Data Link Parameter modification instruction 7

    SaveAT&W

    The above is that under the condition of 340K air rate, you can limit the frequency from 902.400 به 907.500. You can also choose to limit the frequency from 922.800 به 927.600. A channel of 400K is required. At least 51 کانال ها از 902.400 به 927.600 لازم هستند. If the air rate is 230K or below, Only one channel of 280K is needed, which can limit the frequency from 902.400 به 913.500, or the frequency from 916.700 به 927.600. If you need to cancel the restriction, وارد 000.000 at the beginning and end.

دستورالعمل عملکرد فوق برای دو مدل زیر مناسب است:

Digital Data Link for Drones and Robotics, Bi-directional wireless transmission module
پیوند داده دیجیتال برای ماژول انتقال بی‌سیم دو جهته هواپیماهای بدون سرنشین و رباتیک
long-range telemetry radio data transmission 2W PA 50km
انتقال داده رادیویی تله متری دوربرد 2W PA 50km
2 pair four unit wireless data transceiver
2 اتصال دهنده داده های بی سیم چهار واحد را جفت کنید
four units of Radio Telemetry Data Link Parameter modification instruction
چهار واحد دستورالعمل اصلاح پارامتر پیوند داده تله متری رادیویی

سوال بپرسید

← برگشت

از پاسخ شما سپاسگزاریم. ✨