COFDM Relay Repeater
Модуль ретранслятора COFDM для бездротового відеопередавача та приймача дрона БПЛА Vcan1870

Зміст
введення
The module is a relay module, not a completed item. Customers need to add a power amplifier, filters, and receiving and transmitting antennas for it to work effectively. These need to be customized according to the two working frequencies selected by the customer.
To prevent interference, the drone employs a single frequency (напр. 400Mhz) for communication with the relay, and a different frequency (напр. 700Mhz) for communication between the relay module with the receiver. The separation between the two should be as large as possible.
Особливість
- Wireless Video COFDM Video Data demodulation and re-modulation
- Стабільна передача сигналу в NLOS і високошвидкісному русі (less than 600km/hour)
- Регульована робоча частота, пропускна здатність, потужність передачі, і т.д. (Особливий Parameter Configure Tool or UART STM32 LoRA )
- Lowest latency 200-300 мілісекунд
- Widely frequency range 200Mhz-3000Mhz
- підтримка AES256
- Пропускна здатність 1Mhz-8Mhz опціональний
- Video signal repeater for long-distance


введення
специфікація:

IO
| РЧ вхід | Two SMA females (to receive the signal) |
| РЧ вихід | MMCX жіноча (to send out the signal again) |
| control UART | 4Роз'єм PIN PH1,25 мм |
| Вхід живлення | 2PIN-код PH2,54 мм роз'єм Phenix |
| TF-карта | Для оновлення прошивки |
| Світлодіод живлення | red LED, constant light when the device is normally powered |
| Посилання вів | зелений світлодіод, блимає під час передачі отриманих даних |
Демодуляція та модуляція
| Формати модуляції | COFDM(DVB-T) |
| Перевізники | 2До |
| Пропускна здатність | Налаштовується від 1 МГц до 8 МГц, з кроком 1 кГц |
| FEC | 1/2, 2/3, 3/4, 5/6, 7/8 |
| Захисний інтервал | 1/32, 1/16, 1/8, 1/4 |
| Сузір'я | QPSK, 16QAM, 64QAM |
| Бітрейт | 0.5Мбіт/с до 31,67 Мбіт/с |
РФ Отримано
| Смуги частот | 160МГц~860 МГц (need an extra down converter block for 860-2300Mhz) |
| Розмір кроку налаштування | 1KHz |
| Чутливість | -97±1 дБм(BW=8 МГц, QPSK, CR=2/3, GI=1/16) для одного каналу та додайте 3 дБм для двоканального |
РЧ передається
| Смуги частот | 200МГц ~ 2300 МГц(інші смуги можуть підтримуватися спеціальним виготовленням) |
| Розмір кроку налаштування | 1KHz |
| Вимкнення живлення | Настроюється, максимум -5 дБм(залежно від частоти) |
Моніторинг і контроль
This COFDM relay repeater module can complete setup with our Parameter Configure Tool or STM32+LoRA (or other devices) via control uart. With our parameter configure too, the following parameters can be set:
– RX Received frequency (F1) і пропускна здатність (B1)
– TX Transmitted frequency (F2), пропускна здатність (B2), FEC, захисний інтервал, constellation, і потужність передачі
Діапазон температур
Повна специфікація: 0° до +70°C Навколишнє середовище
Зберігання: від –40° до +80°C
Вимоги до живлення
Діапазон введення: 7~24 В постійного струму
Споживання енергії: <250мА при 12 В
Фізичні характеристики
розміри: 73х51х15 мм
Вага брутто: 32.4 грамів
UART AT commands
The AT commands mainly used in the COFDM Wireless Relay Repeater are ATDR, АТСД, ATG, ATSR, ATGR, and ATGB. For the introduction of specific commands, see the document.
FAQs
- Our COFDM Video Transceiver relay repeater supports 170-860Mhz. The COFDM transmitter also supports 2300Mhz, but the COFDM receiver only supports up to 860Mhz, 861-930Mhz receiver our COFDM-221 supports, over 930Mhz-2300Mhz needs to plus the frequency downconverter block to support.
- Our COFDM relay repeater module supports all the COFDM transmitters and receivers, the transmission distance depends on your external power amplifier and filter support.
На даний момент, adding a monitor is not feasible.
The current COFDM repeater design does not include any display output interface, and it also does not support video decoding functionality. The repeater works by directly receiving the COFDM data stream from the receiver module, changing the RF frequency, and retransmitting the data exactly as received.
This architecture is intentionally designed to achieve:
- The simplest and most reliable implementation
- Наднизька затримка
- Minimal processing delay
Since the unit does not decode the video stream internally, there is no video signal available for a local monitor display.
Технічно, yes — Ethernet output can be added.
проте, this would require additional software and hardware development, в тому числі:
- Data buffering and forwarding logic
- Network transmission program development
- Web-based configuration interface
- IP address and port management functions
- System testing and optimization
Because of the extra development workload, this feature would typically require:
- A sufficient order quantity, або
- A separate NRE/development fee
If your project has volume demand or a dedicated budget for customization, we can evaluate this option further.
The COFDM repeater module itself does not include a built-in display or video output interface, so it cannot directly show tuning status or video images. This is because the repeater is designed as a transparent RF relay device that focuses on low latency and real-time frequency translation, without performing video decoding.
проте, the system can still be monitored and optimized in the following ways:
1. LCD Parameter Configuration Tool Board (Рекомендовано)
The repeater can be connected to an external LCD parameter configuration tool board.
Through this tool, you can directly monitor key RF performance indicators such as:
- Received signal strength (RSSI)
- Signal quality (SNR)
- Частота бітових помилок (BER)
- Link status and other RF parameters
These indicators are commonly used to determine whether the link is properly tuned and operating under optimal conditions.
2. Using an External Receiver for Video Monitoring (Додатково)
If real video monitoring is required, you can connect a standard COFDM receiver near the repeater output side.
В даному випадку:
- The repeater still performs RF frequency translation only
- The receiver handles video decoding
- You can connect the receiver to a display or monitor to view the live video
This effectively allows you to check system performance visually if needed.
Important Note
The COFDM repeater itself:
- Does not support video decoding
- Does not output HDMI / CVBS / IP video signals
- Only performs transparent RF relay with frequency conversion
Still have a question?
Будь ласка, зв'яжіться з нами для отримання додаткової інформації.
Send Your Question

The below model is good for a two-way TDD bidirectional link of the Wireless relay transmitter and receiver or wireless transmitter and receiver relay repeater.



iVcan.com –
The Vcan1870 COFDM Relay Repeater module is an excellent addition to any UAV or drone wireless video transmission setup. Designed as a flexible relay, it reliably demodulates incoming COFDM signals and instantly re-modulates them for transmission, ensuring stable long-range video links. Its adjustable frequency, пропускна здатність, and transmission power make it highly adaptable for different environments, while support for AES256 ensures secure communication. With low latency of 200–300ms and robust NLOS performance even at high speeds, this module is perfect for professional drone applications requiring reliable, high-quality video relay.