COFDM Relay Repeater
Modul Pengulang Relai COFDM untuk pemancar dan penerima video nirkabel drone UAV Vcan1870
Daftar isi
pengantar
The module is a relay module, not a completed item. Customers need to add a power amplifier, filter, and receiving and transmitting antennas for it to work effectively. These need to be customized according to the two working frequencies selected by the customer.
To prevent interference, the drone employs a single frequency (misalnya. 400Mhz) for communication with the relay, and a different frequency (misalnya. 700Mhz) for communication between the relay module with the receiver. The separation between the two should be as large as possible.
Fitur
- Wireless Video COFDM Video Data demodulation and re-modulation
- Stable signal transfer in NLOS and high-speed moving (less than 600km/hour)
- Frekuensi kerja yang dapat disesuaikan, lebar pita, daya transmisi, dll. (Spesial Parameter Configure Tool or UART STM32 LoRA )
- Lowest latency 200-300 milidetik
- Widely frequency range 200Mhz-3000Mhz
- Mendukung AES256
- Bandwidth 1Mhz-8Mhz opsional
- Video signal repeater for long-distance
pengantar
Spesifikasi:
IO
| masukan RF | Two SMA females (to receive the signal) |
| keluaran RF | MMCX perempuan (to send out the signal again) |
| control UART | 4Konektor PIN PH1.25mm |
| Daya masuk | 2Konektor feniks PIN PH2.54mm |
| kartu TF | Untuk pembaruan firmware |
| Kekuasaan dipimpin | red LED, constant light when the device is normally powered |
| Tautan dipimpin | dipimpin hijau, berkedip saat mentransmisikan data yang diterima |
Demodulasi dan Modulasi
| Format Modulasi | COFDM(DVB-T) |
| Operator | 2K |
| Bandwidth | Dapat dikonfigurasi dari 1MHz hingga 8MHz, selangkah demi selangkah 1KHz |
| FEC | 1/2, 2/3, 3/4, 5/6, 7/8 |
| Interval penjaga | 1/32, 1/16, 1/8, 1/4 |
| Konstelasi | QPSK, 16QAM, 64QAM |
| Kecepatan bit | 0.5Mbps hingga 31,67Mbps |
RF Diterima
| Pita Frekuensi | 160MHz~860MHz (need an extra down converter block for 860-2300Mhz) |
| Ukuran Langkah Penyetelan | 1KHz |
| Kepekaan | -97±1dBm(BB = 8MHz, QPSK, CR=2/3, GI=1/16) for one channel and add 3dBm for two-channel |
RF Ditransmisikan
| Pita Frekuensi | 200MHz~2300MHz(band lain dapat didukung dengan manufaktur khusus) |
| Ukuran Langkah Penyetelan | 1KHz |
| Matikan listrik | Dapat dikonfigurasi, maksimum -5dBm(tunduk pada frekuensi) |
Pemantauan dan pengendalian
This COFDM relay repeater module can complete setup with our Parameter Configure Tool or STM32+LoRA (or other devices) via control uart. With our parameter configure too, the following parameters can be set:
– RX Received frequency (F1) dan bandwidth (B1)
– TX Transmitted frequency (F2), lebar pita (B2), FEC, interval penjaga, konstelasi, dan daya transmisi
Kisaran suhu
Spesifikasi lengkap: 0° hingga +70°C Lingkungan
Penyimpanan: –40° hingga +80°C
Persyaratan daya
Rentang masukan: 7~24VDC
Konsumsi daya: <250mA@12V
Ciri-ciri Fisik
Ukuran: 73x51x15mm
Berat Kotor: 32.4 gram
UART AT commands
The AT commands mainly used in the COFDM Wireless Relay Repeater are ATDR, ATSD, ATG, ATSR, ATGR, and ATGB. For the introduction of specific commands, see the document.
FAQ
- Our COFDM Video Transceiver relay repeater supports 170-860Mhz. The COFDM transmitter also supports 2300Mhz, but the COFDM receiver only supports up to 860Mhz, 861-930Mhz receiver our COFDM-221 supports, over 930Mhz-2300Mhz needs to plus the frequency downconverter block to support.
- Our COFDM relay repeater module supports all the COFDM transmitters and receivers, the transmission distance depends on your external power amplifier and filter support.
-
iya nih, mendukung.
Modul pemancar modulator encoder Video COFDM hasil pengujian 3.5G dan 4G.
Saat ini, adding a monitor is not feasible.
The current COFDM repeater design does not include any display output interface, and it also does not support video decoding functionality. The repeater works by directly receiving the COFDM data stream from the receiver module, changing the RF frequency, and retransmitting the data exactly as received.
This architecture is intentionally designed to achieve:
- The simplest and most reliable implementation
- Latensi sangat rendah
- Minimal processing delay
Since the unit does not decode the video stream internally, there is no video signal available for a local monitor display.
Technically, yes — Ethernet output can be added.
Namun, this would require additional software and hardware development, termasuk:
- Data buffering and forwarding logic
- Network transmission program development
- Web-based configuration interface
- IP address and port management functions
- System testing and optimization
Because of the extra development workload, this feature would typically require:
- A sufficient order quantity, atau
- A separate NRE/development fee
If your project has volume demand or a dedicated budget for customization, we can evaluate this option further.
The COFDM repeater module itself does not include a built-in display or video output interface, so it cannot directly show tuning status or video images. This is because the repeater is designed as a transparent RF relay device that focuses on low latency and real-time frequency translation, without performing video decoding.
Namun, the system can still be monitored and optimized in the following ways:
1. LCD Parameter Configuration Tool Board (Direkomendasikan)
The repeater can be connected to an external LCD parameter configuration tool board.
Through this tool, you can directly monitor key RF performance indicators such as:
- Received signal strength (RSSI)
- Signal quality (SNR)
- Tingkat kesalahan sedikit (BER)
- Link status and other RF parameters
These indicators are commonly used to determine whether the link is properly tuned and operating under optimal conditions.
2. Using an External Receiver for Video Monitoring (Optional)
If real video monitoring is required, you can connect a standard COFDM receiver near the repeater output side.
Dalam hal ini:
- The repeater still performs RF frequency translation only
- The receiver handles video decoding
- You can connect the receiver to a display or monitor to view the live video
This effectively allows you to check system performance visually if needed.
Important Note
The COFDM repeater itself:
- Does not support video decoding
- Does not output HDMI / CVBS / IP video signals
- Only performs transparent RF relay with frequency conversion
The below model is good for a two-way TDD bidirectional link of the Wireless relay transmitter and receiver or wireless transmitter and receiver relay repeater.
iVcan.com –
The Vcan1870 COFDM Relay Repeater module is an excellent addition to any UAV or drone wireless video transmission setup. Designed as a flexible relay, it reliably demodulates incoming COFDM signals and instantly re-modulates them for transmission, ensuring stable long-range video links. Its adjustable frequency, lebar pita, and transmission power make it highly adaptable for different environments, while support for AES256 ensures secure communication. With low latency of 200–300ms and robust NLOS performance even at high speeds, this module is perfect for professional drone applications requiring reliable, high-quality video relay.