Transmissor e receptor de vídeo drone 100Mbps taxa de dados de alta velocidade longo alcance 100-150km 2x10W PA

Vantagem

Max 100Mbps

Supports connecting 8 Câmeras IP, each with 1080P resolution. Each camera requires an average of 2M~3Mbps. Even if real-time videos of 8 cameras are transmitted at the same time, it requires about 16M~24Mbps, which can be easily handled by this model.

3X RJ45 for IP camera

Both the aerial unit and the ground power supply have three RJ45 interfaces. The aerial unit can be connected to an IP camera, the ground unit can be connected to a computer running Misson Planner or QGroundControl, and can be connected to an RTSP player running 8 windows. It supports converting the serial port data of the flight control to the network port data (UDP or TCP protocol).

(we can offer you the UDP setup video guide)

One RJ45 can connect more IP devices if use ethernet router.(comutador de rede)

Max support 64 nós

Support one point to one point networking, support one point to multi-points and repeater networking.

Ground Unit supports to connect computer or NVR

As computer supports to run RTSP player or IP camera’s application. As the RTSP player, it supports to play 4, 8, 9 ou 16 windows to play the IP camera.

Frequency hopping function to avoid interference

Fully automatic frequency hopping function, automatically compares and selects the frequency with the least interference as the operating frequency.

• Projetamos esta transmissão de vídeo e dados sem fio com uplink e downlink para quem precisa da função de salto automático de frequência.
• Com tecnologia de salto de frequência (FHSS) para garantir uma melhor comunicação de sinal estável, quando o sinal de frequência atual é pior, o sistema mudará automaticamente a frequência de trabalho para outra frequência para um sinal melhor.
• Este módulo de rádio OFDM bidirecional pode funcionar de 566 MHz a 678 MHz ou de 1420 MHz a 1530 MHz de largura de banda. Portanto, a faixa de frequência tem alteração ou salto de largura de banda de 110 MHz. Se você definir a largura de banda de frequência em 10 MHz, então há 11 pontos de frequência para salto.

Recurso

1. The system facilitates the simultaneous downloading and uploading of video data, enabling bidirectional transmission.
2. This is a TDD OFDM full-duplex IP mesh radio wireless transceiver module that’s designed for both video and data transmission.
3. This device features dual radio frequency power, with each of the two channels outputting 24 plus or minus 1 dBm.
4. The sensitivity is measured at -102dBm for a data rate of 1Mbps with a bandwidth of 20MHz.
5. The system’s support for transmission distances ranges from 500 para 2000 meters in ground-to-ground communication and from 5km to 150 kilometers in unmanned aerial vehicle (UAV) to ground communication. (2watts, 5watts, 10watts)
6. The device includes three wireless, transparent transmission Ethernet RJ45 ports, one wireless, transparent transmission serial port for rs232 UART data links, and a single configuration serial UART (TTL) port for ease of setup and configuration.
7. This device has dual antennas, a main antenna and an auxiliary antenna, that offer flexible configuration options: dual transmitting and dual receiving, transmissão única e recepção dupla, or single transmitting and single receiving modes are all possible.
8. This device supports operation within the wireless working frequency bands ranging from 566 para 678 MHz, as well as from 1420 para 1530 MHz.
9. This device is capable of automatically switching between and within frequency bands, supporting a frequency hopping range up to 110Mhz.
10. The wireless bandwidth is configurable across a range of options, including 1.4MHz, 3MHz, 5MHz, 10MHz, 20MHz, and 40MHz, allowing for a maximum air interface rate of up to 100Mbps.
11. The modulation method used is adaptable and automatically selects from QPSK, QAM16, or QAM64, depending on the conditions.
12. This system is designed to support the encryption and decryption of data transmitted wirelessly.
13. This device is capable of supporting wireless ad hoc networks using a mesh communication method, allowing for the connection of up to 32 nodes within the network.
14. Because all node communications share the same working bandwidth, the system’s maximum sharing rate is limited to 100 Mbps. System rates should be distributed adaptively in an equal manner to ensure fairness and efficiency across all system components.
15. This system is capable of supporting a multi-hop routing topology with a maximum of 32 nós, allowing for routing paths of up to 31 lúpulo. The system supports fixed route configurations, and once implemented, these configurations remain permanently in effect.
16. This model supports a maximum moving speed of up to 300 kilometers per hour.
17. This particular board has been designed with, and thus supports, the Morningcore mCX6779K modem at its core.
18. Fórmula de índice de atraso unidirecional(EM): 6*H + (5/2) * N/2 * H * 3, o atraso bidirecional multiplicado por 2 （N é o número de nós em dois saltos, o número de saltos é H). O atraso otimizado entre dois nós: Atraso unidirecional de um salto entre dois nós≤10ms; Atraso de otimização da cadeia de quatro nós: atraso unidirecional de quatro nós, três saltos, salto único≤10ms； 6 Rede de cadeia de pontos,3 saltar, atraso unidirecional50ms；8 pontos, um salto para todos os pontos, atraso unidirecional36ms；8 pontos, salto serial7, atraso unidirecional170ms；32 pontos, um salto para todos os pontos, atraso unidirecional120ms；32 pontos, serial31 Atraso unidirecional de salto3750ms。
19. Atraso na construção da rede de inicialização do nó mestre lógico20s ~ 80s(Não há restrições para módulos. Geralmente, o nó mestre lógico é ligado primeiro.); Partida a frio, atraso desde a inicialização do nó até o acesso à rede<30s Sinal do nó mestre lógico recebido; início quente, atraso de acesso à rede de inicialização do nó escravo<1é(Cenário comum de rede de nó de um salto); Início quente, ligue o nó a partir de um único ponto de frequência e conecte-se à rede<480EM + 160ms*H(H é a contagem de saltos).

Especificação

1. Duplex por Divisão de Tempo (TDD) is a method used for implementing OFDM modulation.
2. This device is capable of supporting two distinct frequency ranges; the first is between 566 e 678 MHz, while the second is between 1420 e 1530 MHz.
3. This device has the ability to support the function of frequency hopping spread spectrum (FHSS) and automatically hop between frequencies.
4. Bandwidth options include 4MHz, 3MHz, 5MHz, 10MHz, 20MHz, and 40MHz.
5. The maximum throughput for this network connection is 100 megabits por segundo.
6. This device boasts dual RF transmission power, operating at 24±1dBm across two channels—one for uplink and one for downlink communication.
7. The constellation for this system supports QPSK, 16QAM, e 64QAM, and it automatically adapts to the best option depending on conditions.
8. The sensitivity level is measured at -95dBm with a 20MHz bandwidth.
9. This device offers IP video data transmission capabilities and is equipped with three Ethernet ports to facilitate this function.
10. This device offers support for serial data transmission, especificamente, it includes one RS232 port and one TTL port for serial communication.
11. Without additional power amplification, a line-of-sight communication range of up to 22 kilometers is achievable between an unmanned aerial vehicle and a ground station, and a line-of-sight range of up to kilometers can be achieved between two ground stations.
12. To extend the range, you can increase the power output by 2, 5, ou 10 watts.
13. This system features a web-based user interface and a control UART for convenient management and monitoring capabilities.
14. Encryption using AES128 is being employed for security purposes.
15. The uplink and downlink streams need to be controlled, with the video stream requiring a higher bandwidth and the data stream needing less.
16. The networking modes supported include one-to-one peer-to-peer, one-to-many peer-to-multipoint, many-to-one multipoint-to-peer, relay/repeater configurations, and mesh or swarm network topologies.
17. The power consumption of this device is less than 7 watts.
18. Dimensões: 28 x 21 x 6cm
19. The weight of the item is recorded at 4461 gramas.
20. The permissible working temperature range for this is from -20℃ to +65℃.
21. The recommended storage temperature ranges from -40℃ to +80℃.

Sealed Housing without cooling fan

The customer required the housing to be designed for use on board and to be waterproof, so the housing is sealed and has no cooling fan.

Weight and Dimension