جهاز إرسال واستقبال فيديو بدون طيار بمعدل بيانات عالي السرعة 100 ميجابت في الثانية وطويل المدى 100-150 كجم 2x10 وات PA

ميزة

Max 100Mbps

Supports connecting 8 كاميرات IP, each with 1080P resolution. Each camera requires an average of 2M~3Mbps. Even if real-time videos of 8 cameras are transmitted at the same time, it requires about 16M~24Mbps, which can be easily handled by this model.

3X RJ45 for IP camera

Both the aerial unit and the ground power supply have three RJ45 interfaces. The aerial unit can be connected to an IP camera, the ground unit can be connected to a computer running Misson Planner or QGroundControl, and can be connected to an RTSP player running 8 windows. It supports converting the serial port data of the flight control to the network port data (UDP or TCP protocol).

(we can offer you the UDP setup video guide)

One RJ45 can connect more IP devices if use ethernet router.(network switch)

ماكس الدعم 64 العقد

Support one point to one point networking, support one point to multi-points and repeater networking.

Ground Unit supports to connect computer or NVR

As computer supports to run RTSP player or IP camera’s application. As the RTSP player, it supports to play 4, 8, 9 أو 16 windows to play the IP camera.

Frequency hopping function to avoid interference

Fully automatic frequency hopping function, automatically compares and selects the frequency with the least interference as the operating frequency.

• We designed this wireless video and data transmission with uplink and downlink for those who need the frequency automatic hopping function.
• With frequency hopping technology (تم تصميم هذا النموذج لنقل الفيديو والبيانات لاسلكيًا باستخدام ارتباط بيانات لاسلكي ثنائي الاتجاه) to ensure better stable signal communication, when the current frequency signal is worse, the system will automatically change the working frequency to another frequency for a better signal.
• This bidirectional OFDM radio module can work from 566Mhz to 678MHz or from 1420Mhz to 1530MHz bandwidth. So the frequency range has 110Mhz bandwidth change or hopping. If you set the frequency bandwidth at 10 ميغاهيرتز, then there are 11 frequency points for hopping.

ميزة

1. The system facilitates the simultaneous downloading and uploading of video data, enabling bidirectional transmission.
2. This is a TDD OFDM full-duplex IP mesh radio wireless transceiver module that’s designed for both video and data transmission.
3. This device features dual radio frequency power, with each of the two channels outputting 24 plus or minus 1 ديسيبل.
4. The sensitivity is measured at -102dBm for a data rate of 1Mbps with a bandwidth of 20MHz.
5. The system’s support for transmission distances ranges from 500 ل 2000 meters in ground-to-ground communication and from 5km to 150 kilometers in unmanned aerial vehicle (الطائرات بدون طيار) to ground communication. (2واتس, 5واتس, 10واتس)
6. The device includes three wireless, transparent transmission Ethernet RJ45 ports, one wireless, transparent transmission serial port for rs232 UART data links, and a single configuration serial UART (TTL) port for ease of setup and configuration.
7. This device has dual antennas, a main antenna and an auxiliary antenna, that offer flexible configuration options: dual transmitting and dual receiving, single transmitting and dual receiving, or single transmitting and single receiving modes are all possible.
8. This device supports operation within the wireless working frequency bands ranging from 566 ل 678 ميغاهيرتز, as well as from 1420 ل 1530 ميغاهيرتز.
9. This device is capable of automatically switching between and within frequency bands, supporting a frequency hopping range up to 110Mhz.
10. The wireless bandwidth is configurable across a range of options, including 1.4MHz, 3ميغاهيرتز, 5ميغاهيرتز, 10ميغاهيرتز, 20ميغاهيرتز, and 40MHz, allowing for a maximum air interface rate of up to 100Mbps.
11. The modulation method used is adaptable and automatically selects from QPSK, QAM16, or QAM64, depending on the conditions.
12. This system is designed to support the encryption and decryption of data transmitted wirelessly.
13. This device is capable of supporting wireless ad hoc networks using a mesh communication method, allowing for the connection of up to 32 nodes within the network.
14. Because all node communications share the same working bandwidth, the system’s maximum sharing rate is limited to 100 ميغابت في الثانية. System rates should be distributed adaptively in an equal manner to ensure fairness and efficiency across all system components.
15. This system is capable of supporting a multi-hop routing topology with a maximum of 32 العقد, allowing for routing paths of up to 31 القفزات. The system supports fixed route configurations, and once implemented, these configurations remain permanently in effect.
16. This model supports a maximum moving speed of up to 300 kilometers per hour.
17. This particular board has been designed with, and thus supports, the Morningcore mCX6779K modem at its core.
18. One-way delay index formula(ms): 6*ح + (5/2) * N/2 * ح * 3, the two-way delay multiplied by 2（N is the number of nodes within two hops, the number of hops is H). The optimized delay between two nodes: One-hop one-way delay between two nodes≤10ms; Four-node chain optimization delay: four-node three-hop single-hop one-way delay≤10ms； 6 Point chain networking,3 قفزة, one-way delay50ms；8 نقاط, one hop for all points, one-way delay36ms；8 نقاط, serial7 hop, one-way delay170ms；32 نقاط, one hop for all points, one-way delay120ms；32 نقاط, serial31 Jump one-way delay3750ms。
19. Logical master node power-on network construction delay20s~80s(There are no restrictions on modules. عمومًا, the logical master node is powered on first.); Cold start, delay from node startup to network access<30s Received logical master node signal; hot start, slave node startup network access delay<1ق(Ordinary one-hop node networking scenario); Hot start, power on the node from a single frequency point and connect to the network<480ms + 160ms*H(H is the hop count).

تخصيص

1. دوبلكس بتقسيم الزمن (تد) is a method used for implementing OFDM modulation.
2. This device is capable of supporting two distinct frequency ranges; the first is between 566 و 678 ميغاهيرتز, while the second is between 1420 و 1530 ميغاهيرتز.
3. This device has the ability to support the function of frequency hopping spread spectrum (تم تصميم هذا النموذج لنقل الفيديو والبيانات لاسلكيًا باستخدام ارتباط بيانات لاسلكي ثنائي الاتجاه) and automatically hop between frequencies.
4. Bandwidth options include 4MHz, 3ميغاهيرتز, 5ميغاهيرتز, 10ميغاهيرتز, 20ميغاهيرتز, and 40MHz.
5. The maximum throughput for this network connection is 100 megabits per second.
6. This device boasts dual RF transmission power, operating at 24±1dBm across two channels—one for uplink and one for downlink communication.
7. The constellation for this system supports QPSK, 16QAM, و64QAM, and it automatically adapts to the best option depending on conditions.
8. The sensitivity level is measured at -95dBm with a 20MHz bandwidth.
9. This device offers IP video data transmission capabilities and is equipped with three Ethernet ports to facilitate this function.
10. This device offers support for serial data transmission, specifically, it includes one RS232 port and one TTL port for serial communication.
11. Without additional power amplification, a line-of-sight communication range of up to 22 kilometers is achievable between an unmanned aerial vehicle and a ground station, and a line-of-sight range of up to kilometers can be achieved between two ground stations.
12. To extend the range, you can increase the power output by 2, 5, أو 10 واتس.
13. This system features a web-based user interface and a control UART for convenient management and monitoring capabilities.
14. Encryption using AES128 is being employed for security purposes.
15. The uplink and downlink streams need to be controlled, with the video stream requiring a higher bandwidth and the data stream needing less.
16. The networking modes supported include one-to-one peer-to-peer, one-to-many peer-to-multipoint, many-to-one multipoint-to-peer, relay/repeater configurations, and mesh or swarm network topologies.
17. The power consumption of this device is less than 7 واتس.
18. الأبعاد: 28 س 21 x 6cm
19. The weight of the item is recorded at 4461 جرام.
20. The permissible working temperature range for this is from -20℃ to +65℃.
21. The recommended storage temperature ranges from -40℃ to +80℃.

Sealed Housing without cooling fan

The customer required the housing to be designed for use on board and to be waterproof, so the housing is sealed and has no cooling fan.

Weight and Dimension