AT Command Manual
The AT Command may be slightly different for different model versions. This AT command document is a basic description of the AT command for our modem Model for your reference.
This document applies to these models: TX900 과 Vcan1681
Download the TX900 AT command documents PDF
목차
1.1 AT^DACS: Access to the State
| The Command | Possible response (에스) |
| The AT ^ DACS = < N > | |
| The AT ^ DACS? | ^ DACS: < N >, < 상태 > |
| The AT ^ DACS =? | ^DACS: (list of supported <N>에스) |
The Description
The execution command is used to set the switch state of ^DACSI: <상태> escalation, 어느
is turned off by default at the beginning of startup. When the setting is turned on, the current state will be reported once.When active report is opened, the access node shall report the indication of access status after successful access;After the central node starts successfully, it can be regarded as a successful access. After determining the type of central node, the access status can be reported.
The query command is used to query the current escalation switch state and the current access state.
The test command is used to test whether the command is supported and to query the value range of the <N> 매개변수.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<N>: integer type, indicating the active escalation
switch status
0: 끄다
1: ...에
2: query the current information <상태>: integer type, indicating the access status
0: not accessed
1: accessed
예
The AT ^ DACS = 1 < CR > < LF > < CR > < LF > ^ DACSI: 0 < CR > < LF > < CR > < LF > 승인 < CR > < LF > < CR > < LF > ^ DACSI: 1 < CR > < LF > the AT ^ DACS?
< CR > < LF > < CR > < LF > ^ DACS: 1, 1 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DACS =?
< CR > < LF > < CR > < LF > ^ DACS: (0-1) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.2 AT ^ DRPC: Radio Parameter Configure
| The Command | Possible response (에스) |
| The AT ^ DRPC = < freq >, < 대역폭 >, < 힘 > | |
| The AT ^ DRPC? | ^ DRPC: < freq >, < 대역폭 >, < 힘 > |
| The AT ^ DRPC =? | ^DRPC: (list of supported <freq>에스), (list of supported <대역폭>에스) |
The Description
Execute the command for parameter Settings in the access state and save to NVRAM. The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
승인 에스u기음기음essful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<freq>: integer type, indicating frequency point frequency, unit 100KHz, 범위
(8060-8259,14279-14478,24015-24814) <대역폭>: integer type, indicating bandwidth
0:1.4중
1:3 중
2:5 중
3:10 중
4: 15엠 (지원되지 않음)
5: 20엠
<힘>: “정수” 유형, represents the fixed power of the center node, unit dBm, range from “-40” 에게 “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall prevail.
예
The AT ^ DRPC = 24415, 1, “27” < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DRPC?
< CR > < LF > < CR > < LF > ^ DRPC: 24415, 1, “27” < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DRPC =?
< CR > < LF > < CR > < LF > ^ DRPC: 15-24814178 (8060-8259142, 79-14478240, 50-18050), (0 에게 5) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.3 AT^DRPS: Radio Parameter Store in NVRAM
| The Command | Possible response (에스) |
| The AT ^ DRPS = < freq >, < 대역폭 >, < 힘 > | |
| The AT ^ DRPS? | ^ DRPS: < freq >, < 대역폭 >, < 힘 > |
| The AT ^ DRPS =? | ^DRPS: (list of supported <freq>에스), (list of supported <대역폭>에스) |
The Description
The execute command is used to save parameters to NVRAM, after saving power and restart to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
승인 에스u기음기음essful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<freq>: integer type, indicating frequency point frequency, unit 100KHz, 범위
(8060-8259,14279-14478,24015-24814) <대역폭>: integer type, indicating bandwidth
0:1.4중
1:3 중
2:5 중
3:10 중
4: 15엠 (지원되지 않음)
5: 20엠
<힘>: “정수” 유형, represents the fixed power of the center node, unit dBm, range from “-40” 에게 “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall prevail.
예
The AT ^ DRPS = 24415, 1, “27” < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DRPS?
< CR > < LF > < CR > < LF > ^ DRPS: 24415, 1, “27” < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DRPS =?
< CR > < LF > < CR > < LF > ^ DRPS: 15-24814178 (8060-8259142, 79-14478240, 50-18050), (0 에게 5) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.4 AT^DSSMTP: Set Slave Max Tx Power
| The Command | Possible response (에스) |
| The AT ^ DSSMTP = < 힘 > | |
| The AT ^ DSSMTP? | ^ DSSMTP: < freq >, < 대역폭 >, < 힘 > |
| The AT ^ DSSMTP =? |
The Description
The execute command is used to save parameters to NVRAM, after saving power and restart to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
승인 에스u기음기음essful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<힘>: “정수” 유형, from the maximum transmitted power of the node, unit dBm, range from “-40” 에게 “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall be taken as the criterion.
예
The AT ^ DSSMTP = “- 10” < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DSSMTP?
< CR > < LF > < CR > < LF > “- 10” < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DSSMTP =?
< CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.5 AT ^ DRPR: Radio Parameter Report
| The Command | Possible response (에스) |
| The AT ^ DRPR = < N > | |
| The AT ^ DRPR? | ^ DRPR: < N > |
| The AT ^ DRPR =? | ^DRPR: (list of supported <N>에스) |
The Description
Execute the command to set the local wireless parameter report ^DRPRI:그만큼 < 색인 >, <
earfcn >, < cell_id >, < rssi >, < pathloss >, < RSRP >, < RSRQ >, < SNR >, < short >, <
tx_power >, < dl_throughput_total_tbs >, < ul_thrpughput_total_tbs >, < dlsch_tb_error_per >,
< the MCS >, < rb_num >, < wide_cqi >, <Dlsch_tb_error_per_total >,< Max_Snr>,< Min_Snr>,< dl_total_tbs_g_rnti > on and off by default.The switch is only valid if the local machine is used as the access node. There is no active escalation for the center node even if the switch is on. The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OK Successful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<N>: integer type, indicating the active escalation switch status 0: 끄다 1: ...에
2:Query current information <색인>: integer type, indicating port index no. 1: 포트 12: 포트
2<earfcn>: integer type, frequency information of measurement result <cell_id>: integer type, cell information of measurement result <rssi>: string type, rssi measurement value,dBm, format as “±value”(제외하고 “0”)”-141″ 에게 “-44”:RSSI measurements
“+32767”: invalid value <pathloss>: integer type, pathloss,dBm0 to 191: pathloss
32767: invalid value < RSRP >: string type, RSRP measurement value,dBm, format as
“±value”(제외하고 “0”)”-141″ 에게 “-44”: RSRP measurement value
“+32767”: invalid value < RSRQ >: string type, RSRQ measurement value,dBm, format as “±value”(제외하고 “0”), the actual value needs to be divided by 10 processing “-196” 에게 “-30”: RSRQ measurement value
“+32767”: invalid value < SNR >: string type,SNR measurement, format as “±value”(제외하고
“0”)
“-50” 에게 “+50”: SNR measurement value
“+32767”: invalid value < 거리 >: integer type, distance from the opposite end node, in meters, value range [0, 5000]
< tx_power >:string type, transmitted power, dBm, 체재 “±value”(제외하고 “0”) “-50” 에게 “+50”: transmitted power
“+32767”: invalid value < dl_throughput_total_tbs >:integer type, downlink throughput information, sum of TB size in escalation cycle, Byte, 범위 [0,12000000]
< ul_thrpughput_total_tbs >: integer type, upline throughput information, sum of TB size in escalation cycle, Byte, 범위 [0,12000000]
< dlsch_tb_error_per >:integer type, report the percentage of error in the cycle, 범위 [0,100]
< MCS >: MCS, value range [0,29]
<rb_num>: number of RB, value range [6,100]
<wide_cqi>: broadband CQI, value range [1,15]
<dlsch_tb_error_per_total>: report the total error percentage after entering the connection state, 범위 [0,100]
< Max_Snr>: maximum SNR within 10000ms, value range [-40,40]
< Min_Snr>:10000ms minimum SNR, value range [-40,40]
<dl_total_tbs_g_rnti>: integer type, total_tbsize for multicast packets
예
The AT ^ DRPR = 1 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DRPR?
< CR > < LF > < CR > < LF > ^ DRPR: 1 < CR > < LF > < CR > < LF > 승인 < CR > < LF > < CR > < LF > ^ DRPRI: 1100 16일, “- 46”, 20, “60”, “195”, “0”, 4000, “- 36”,
10000000500000,10,15,3,15, 50, “+ 30”, “25”, 15000 < CR > < LF > < CR > < LF > ^ DRPRI:0 dec, 2100-106 “, 115, “100”, “194”, “+ 20, 4000,” – 36 “, 10000000500000,10,15,3,15, 50, “+
35″, “to 30”, 15000 < CR > < LF > the AT ^ DRPR =?
< CR > < LF > < CR > < LF > ^ DRPR: (0-1) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.6 AT^DAPR: Access Nodes radio Parameter Report
| The Command | Possible response (에스) |
| The AT ^ DAPR = < N > | |
| The AT ^ DAPR? | ^ DAPR: < N > |
| The AT ^ DAPR =? | ^DAPR: (list of supported <N>에스) |
The Description
Execute the command to set the wireless parameters of the central node to report the access node ^DAPRI: 그만큼 < IPv6Address >, < the index >, < rssi >, < pathloss >, < RSRP >, < RSRQ >, < SNR >, < short >, < tx_power >, < dl_throughput_total_tbs >, < ul_throughput_total_tbs >, < dlsch_tb_error_per >, < dlsch_tb_error_per_total >, < Max_Snr >, < Min_Snr >, < dlThe on-off state of _total_tbs_g_rnti>, turned off by default at startup.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<N>: integer type, indicating the active escalation switch status 0: 끄다 1: ...에
< 2: query the current information IPv6 address >: string type, has the IP address of the access nodes, is made up of 16 Numbers (0-255), in between each group number. ‘ ‘no, format is: a1, a2, a3, a4, a5, a6, a7, a8.. A9 a10. A11. A12. A13. A14. A15. A16
<색인>: integer type, indicating port index no. 1: 포트 12: port 2<rssi>: string type, rssi measurement value,dBm, format as “±value”(제외하고 “0”)”-141″ 에게 “-44”: rssi measurement value
“+32767”: invalid value <pathloss>: integer type, pathloss,dBm0 to 191: pathloss
32767: invalid value < RSRP >: string type, RSRP measurement value,dBm, format as
“±value”(제외하고 “0”)”-141″ 에게 “-44”: RSRP measurement value
“+32767”: invalid value < RSRQ >: string type, RSRQ measurement value,dBm, format as “±value”(제외하고 “0”), the actual value needs to be divided by 10 processing “-196” 에게 “-30”: RSRQ measurement value
“+32767”: invalid value < SNR >: string type,SNR measurement, format as “±value”(제외하고
“0”)
“-50” 에게 “+50”: SNR measurement value
“+32767”: invalid value < 거리 >: integer type, distance from the opposite end node, in meters, value range [0, 5000]
< tx_power >: string type, transmitted power, dBm, 체재 “±value”(제외하고 “0”) “-50” 에게 “+50”: transmitted power
“+32767”: invalid value < dl_throughput_total_tbs >: integer type, downlink throughput information, sum of TB size in escalation cycle, Byte, 범위 [0,12000000]
< ul_thrpughput_total_tbs >: integer type, upline throughput information, sum of TB size in escalation cycle, Byte, 범위 [0,12000000]
< dlsch_tb_error_per >: integer type, report the percentage of error in the cycle, 범위 [0,100]
< MCS >: MCS, value range [0,29]
<rb_num>: number of RB, value range [6,100]
<wide_cqi>: broadband CQI, value range [1,15]
<dlsch_tb_error_per_total>: report the total error percentage after entering the connection state, 범위 [0,100]
< Max_Snr>: maximum SNR within 10000ms, value range [-40,40]
< Min_Snr>:10000ms minimum SNR, value range [-40,40]
<dl_total_tbs_g_rnti>: integer type, total_tbsize for multicast packets
예
The AT ^ DAPR = 1 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DAPR?
< CR > < LF > < CR > < LF > ^ DAPR: 1 < CR > < LF > < CR > < LF > 승인 < CR > < LF > < CR > < LF > ^ DAPRI:”1.2.3.4.0.0.0.0.1.2.3.4.200.201.202.203″, 1, “- 46”, 20, “60”, “195”, “0”, 4000, “-
36″, 10000000500000,10,15,3,15, 50, “+ 30”, “25”, 16000 < CR > < LF > < CR > < LF > ^ DAPRI:”1.2.3.4.0.0.0.0.1.2.3.4.200.201.202.203″, 2, “106”, 115, “100”, “194”, “+ 20, 4000,” –
36 “, 10000000500000,10,15,3,15,50, “+ 35”, “to 30”, 16000 < CR > < LF > the AT ^ DAPR =?
< CR > < LF > < CR > < LF > ^ DAPR: (0-1) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.7 AT^DAOCNDI: Communication Network configuration
| The Command | Possible response (에스) |
| The AT ^ DAOCNDI = < band_bitmap > | |
| The AT ^ DAOCNDI? | ^ DAOCNDI: < band_bitmap > |
| The AT ^ DAOCNDI =? |
The Description
The execution command is used to set the operating frequency information of the ad-hoc network communication equipment, and the setting is followed by power-on and power-on. The query command is used to query the operating frequency information of AD hoc network communication equipment.
The test command is used to test whether the command is supported.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<band_bitmap>: string type(without double quotes),in hexadecimal format, the rightmost bit is the least significant bit (LSB/bit0).
Bit0:800 m frequency band
Bit2:1.4 G band
Bit3:2.4 G band
예
AT^DAOCNDI=0D<CR><LF>// Set band as 800M/ 1.4G / 2.4지 <CR><LF>승인<CR><LF> AT^DAOCNDI=01<CR><LF>// Set band as 800M<CR><LF>승인<CR><LF>
The AT ^ DAOCNDI?< CR > < LF > < CR > < LF > ^ DAOCNDI: 0 디 < CR > < LF > < CR > < LF >
승인 < CR > < LF > the AT ^ DAOCNDI =?
< CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.8 AT ^ DDTC: Device Type Configuration
| The Command | Possible response (에스) |
| The AT ^ DDTC = < 유형 > | |
| The AT ^ DDTC? | ^ DDTC: < 유형 >, < working type > |
| The AT ^ DDTC =? | ^ DDTC: (the list of supported < 유형 > 에스) |
The Description
The execute command is used to set the type of AD hoc network communication device, which needs to be set before (+CFUN=1) startup, and takes effect after +CFUN=1 startup.When the type of terminal working equipment is determined, actively report
^DDTCI:<유형>,<working type>
The query command is used to query ad-hoc network communication device type information.
The test command is used to test whether the command is supported.
The Final result code
승인 에스u기음기음essful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<유형>: integer type, indicating the device type
0: 자동 1: center node
2: 액세스 노드 <working type>: integer type, indicating the current actual working device type
0: 자동
1: center node
2: 액세스 노드
예
The AT ^ DDTC = 0 < CR > < LF > < CR > < LF > 승인 < CR > < LF >
The AT ^ DDTC?< CR > < LF > < CR > < LF > ^ DDTC: 0, 0 < CR > < LF > < CR > < LF > 승인 < CR >
< LF >
< CR > < LF > ^ DDTCI: 0, 1 < CR > < LF > the AT ^ DDTC =?
< CR > < LF >
< CR > < LF > ^ DDTC: (2-0) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.9 AT^DAPI: Access Password ID of Auto Organized Communication
Network configuration
The Command Possible response (에스)
| The AT ^ DAPI = < password_id > | |
| The AT ^ DAPI? | ^ DAPI: < password_id > |
| The AT ^ DAPI =? |
The Description
The Settings command is used to set the PASSWORD ID for the ad-hoc networking device. Power on again.
The query command is used to query the PASSWORD ID of the ad-hoc networking device. The test command is used to test whether the command is supported.
The Final result code
승인 에스u기음기음essful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<password_id>: string type, in HEX format, data supports up to 32 바이트 (HEX string 64 characters)
예
The AT ^ fbfa DAPI = “30313233” < CR > < LF > < CR > < LF > 승인 < CR > < LF >
The AT ^ DAPI?< CR > < LF > < CR > < LF > ^ DAPI: “30313233 fbfa” < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DAPI =?
< CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.10 AT ^ DSTC: Set TDD configuration
| The Command | Possible response (에스) |
| The AT ^ DSTC = < conf > | |
| The AT ^ DSTC? | ^ DSTC: < the conf > |
| The AT ^ DSTC =? | ^DSTC: (list of supported <conf>에스) |
The Description
The execution command is used to set the parameters. After setting, the power down restarts to take effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<conf>: integer type, indicating TDD config setting
0: config0 (2D3U)
1: config1 (3D2U) (remote mode not supported)
2: Config2 (4D1U) (remote mode not supported)
3: Config3 (1D4U)
예
The AT ^ DSTC = 0 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DSTC?
< CR > < LF > < CR > < LF > ^ DSTC: 0 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DSTC =?
< CR > < LF > < CR > < LF > ^ DSTC: (0-3) < CR > < LF > < CR > < LF > 승인 < CR >
< LF >
1.11 AT^DPDBC: PS Data command Configuration
| The Command | Possible response (에스) |
| The AT ^ DPDBC = < data_pri >, < dev_name > | |
| The AT ^ DPDBC =? | DPDBC: (range of support <data_pri>에스), (range of support <dev_name>에스) |
The Description
The execute command is used to set the data hosting priority to the transport port. The setting is valid before starting up.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<data_pri>: integer type, indicating the priority of data-bearing type, ~에 이르기까지 1 에게 3, the smaller the value, the higher the priority
<dev_name>: string type, which represents the transport port name
LMI40: LMI40 device, to be used by 0
LMI41: LMI41 device, to be used by 0
LMI43: LMI43 device, to be used by 1
LMI44: LMI44 device, to be used by 1
UAV_COMM: com-uart communication interface MEDIA0~ MEDAI15: public MEDIA data interface, in which MEDIA0~ MEDAI7 is for use by 0 and MEDIA7~ MEDAI15 is for use by 1
예
The AT ^ DPDBC = 1, “LMI40 < CR >”
< CR > < LF > 승인 < CR > < LF > The AT ^ DPDBC =?그만큼 < CR >
< CR > < LF > ^ DPDBC: (1-3), (” LMI40 “, “LMI41”, “LMI43”, “LMI44”, “MEDIA0” ~ “MEDIA15”) < CR > < LF >
< CR > < LF > 승인 < CR > < LF >
1.12 AT^DUBR: UART Baud Rate setting
| The Command | Possible response (에스) |
| The AT ^ DUBR = < rate > | |
| The AT ^ DUBR? | ^ DUBR: < rate > |
| The AT ^ DUBR =? | DUBR: (list of supported <rate>에스) |
The Description
The execution command is used to set the UART port baud rate parameter, after setting the power down reboot takes effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<rate>: integer type, represents the UART port baud rate parameter, and the value range is as follows:
1200:1200 byte/s
2400:2400 byte/s
4800:4800 byte/s
9600:9600 byte/s
19200:19200 byte/s
28800:28800 byte/s
38400:38400 byte/s
57600:57600 byte/s
115200:115200 byte/s
예
The AT ^ DUBR = 57600 < CR >
< CR > < LF > 승인 < CR > < LF >
The AT ^ DUBR?< CR > < LF > < CR > < LF > ^ DUBR: 57600 < CR > < LF > < CR > < LF > 승인 < CR > < LF >
The AT ^ DUBR =?그만큼 < CR >
< CR > < LF > ^ DUBR: (1200240 0480 0960 0192 00288 00384 00576 00115 200) < CR > < LF >
< CR > < LF > 승인 < CR > < LF >
1.13 AT^DCIAC: Ciphering and integrityarithmetic Configuration
| The Command | Possible response (에스) |
| The AT ^ DCIAC = < arith > | |
| The AT ^ DCIAC? | ^ DCIAC: < arith > |
| The AT ^ DCIAC =? | ^DCIAC: (list of supported <arith>에스) |
The Description
The execution command is used to set the encryption and insurance algorithm, after setting the power restart effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
승인 에스u기음기음essful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<arith>: integer type, represents the encryption and completion algorithm, the value range is as follows:
0: none ciphering and integrality
1: SNOW
2: the AES
3: ZUC
예
The AT ^ DCIAC = 2 < CR >
< CR > < LF > 승인 < CR > < LF >
The AT ^ DCIAC?< CR > < LF > < CR > < LF > ^ DCIAC: 2 < CR > < LF > < CR > < LF > 승인 < CR >
< LF >
The AT ^ DCIAC =?그만큼 < CR >
< CR > < LF > ^ DCIAC: (0-3) < CR > < LF >
< CR > < LF > 승인 < CR > < LF >
1.14 AT ^ DFHC: Frequency Hopping Control
| The Command | Possible response (에스) |
| The AT ^ DFHC = < N > | |
| The AT ^ DFHC? | ^ DFHC: < N > |
| The AT ^ DFHC =? | ^DFHC: (list of supported <N>에스) |
The Description
The execution command is used to set the frequency hopping parameters. After setting, the power down restarts to take effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
승인 에스u기음기음essful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<N>: integer type, indicating the frequency hopping function setting 0: turn off the frequency hopping function
1: turn on the frequency hopping function
예
The AT ^ DFHC = 0 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DFHC?
< CR > < LF > < CR > < LF > ^ DFHC: 0 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DFHC =?
< CR > < LF > < CR > < LF > ^ DFHC: (0-1) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.15 AT ^ LCMFUN Set module functionality
| The Set command The AT ^ LCMFUN = < ...에 > | Set command is used to Set module power on or off. The Response: OK If the error is related to ME functionality: + CME ERROR: 100 The Parameter: < ...에 >: integer of power on or off 0: poweroff 1: poweron 2: poweroff-but not close electric on FLASH/DDR |
| The Read command The AT ^ LCMFUN? | The Response: 그만큼 < ...에 > OK The Parameter |
| See the set command | |
| The Test command The AT ^ LCMFUN =? | The Response: ^LCMFUN: (list of supported < ...에 >에스) OK The Parameter See the set command 예 ^ LCMFUN: (0, 2) 승인 |
| The Reference | |
| 메모 |
1.16 AT ^ POWERCTL Power Ctrl
| The Set Command The AT ^ POWERCTL = < value > | Set command is used to reboot OS The Response: OK If the error is related to ME functionality: + CME ERROR: 100 The Parameter: < value>: integer of the reboot OS,only one value 1 |
| The Test Command The AT ^ POWERCTL =? | The Response: POWERCTL: (list of supported< vlaue >) OK The Parameter See the set command Example ^ POWERCTL: 1 승인 |
The Description
The execute command is used to restart the module.
| The Response | The result |
| 승인 | Successful |
| ERROR or +CME ERROR: <err> | The Command performing failed |
예
The AT ^ POWERCTL = 1 < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.17 AT^DSSMTP: Set Slave Max Tx Power
| The Command | Possible response (에스) |
| The AT ^ DSSMTP = < 힘 > | |
| The AT ^ DSSMTP? | ^ DSSMTP: < 힘 > |
| The AT ^ DSSMTP =? |
The Description
The execute command is used to save parameters to NVRAM, after saving in and out of flight to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<힘>: “정수” 유형, from the maximum transmitted power of the node, unit dBm, range from “-40” 에게 “40”, and if the setting exceeds the maximum supported by the terminal, the maximum supported by the terminal shall be taken as the criterion.
예
The AT ^ DSSMTP = “- 10” < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT
^ DSSMTP?
< CR > < LF > < CR > < LF > “- 10” < CR > < LF > < CR > < LF > 승인 < CR > < LF >
the AT ^ DRPS =?
< CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.18 AT^DSONMCS: Modulation and Coding Scheme Index Set
| The Command | Possible response (에스) |
| The AT ^ DSONMCS = < 방법 >,, < Mcs > [] | |
| The AT ^ DSONMCS? | ^ DSONMCS: < 방법 >, < the Mcs > |
| The AT ^ DSONMCS =? | DSONMCS: (list of supported <방법>에스),(list of supported <Mcs>에스) |
The Description
Setting command is used to set MCS index value switch and index value, if not on, is not allowed to change the MCS value; If the MCS switch is turned on, the MCS index value is allowed to be set, effective immediately and saved to NVRAM for permanent effect. The default switch is off.
The query command queries the current set value.
The test command is used to test the Settings that the command supports. NOTE: this instruction can only be issued from the primary node
The Final result code
좋아요 이자형아르 자형아르 자형y.error or +CME ERROR: <err>Command performing failed.
Defined values
<방법>: integer type, which represents the function setting of MCS index value. 기본적으로, the setting function is not turned on 0: the setting function is turned off
1: open the setting function
<Mcs>: integer type, indicating the Mcs index value, which ranges from 0 to 27.The default value is 27
예
The AT ^ DSONMCS = 1, 5 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DSONMCS?
< CR > < LF > < CR > < LF > ^ DSONMCS: 1, 5 < CR > < LF > < CR > < LF > 승인 < CR > < LF > 그만큼
AT ^ DSONMCS =?
< CR > < LF >
< CR > < LF > ^ DSONMCS: (0-1), (0-27) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.19 AT ^ DLF: Lock Freq
| The Command | 피ossible response (에스) |
| The AT ^ DLF = < lock_type > [, < freq >] | |
| The AT ^ DLF? | ^ DLF: < lock_type > [, < freq >] |
| The AT ^ DLF =? | ^DLF: (list of supported<;Lock_type>에스), (list of supported lock <freq>에스) |
The Description
The execution command is used to control the user to set the lock frequency information, the setting value is saved to NVRAM, and the in-and-out flight takes effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<LockType >: integer type, indicating that the user sets the lock specified frequency switch setting 0: unlocking or unlocking the frequency point
1: lock the specified frequency point
<Freq>: integer type, indicating frequency point frequency, unit 100KHz, 범위
(8060-8259,14279-14478,24015-248140)
예
The AT ^ DLF = 1143 50 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DLF?
< CR > < LF > < CR > < LF > ^ DLF: 1, 14350 < CR > < LF > < CR > < LF > 승인 < CR > < LF > 그만큼
AT ^ DLF =?
< CR > < LF > < CR > < LF > ^ DLF: (0-1), (8060-8259142
79-14478240-15-24814178-50-18050) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.20 AT^DSONSSF: Set Special Function For SON
| 티시간e Command | 피ossible response (에스) |
| The AT ^ DSONSSF = < FuncType > [, < 값 >] | |
| The AT ^ DSONSSF? | ^ DSONSSF: < FuncType > [, < 값 >] |
| The AT ^ DSONSSF =? | DSONSSF: (list of supported (<FuncType>에스),(list of supported (<Values>에스) |
The Description
The Settings command is used to select and/or set specific functions.AT^DSONSSF=<FuncType> is used to select a particular function, and the result of the selection can be used in the query command.AT^DSONSSF=<FuncType>, 과 <값> is used to set the Value of a particular function.
The query command returns the current value of the selected function (set by
AT^DSONSSF=<FuncType>).If no function is selected, the default function is returned.
The test command returns the supported value.
The set parameters are stored in NVRAM and take effect on the next power-on.
The Final result code
Okerry.error or +CME ERROR: <err>Command performing failed.
Defined values
<FuncType >: integer type, identifying a specific function
0: send ACK packets in the normal order
1: access to external network
2: the DRX shut down
3. PING and low latency service optimization
4: low power mode
Other value reservation
< 값 > : an integer type
0: not enabled (제어)
1: enable (제어)
예
The AT ^ DSONSSF = 0, 1 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DSONSSF?
< CR > < LF > < CR > < LF > ^ DSONSSF: 0, 1 < CR > < LF > < CR > < LF > 승인 < CR > < LF > 그만큼
AT ^ DSONSSF =?
< CR > < LF > < CR > < LF > ^ DSONSSF: (0 에게 4), (0-1) < CR > < LF > < CR > < LF > 승인 < CR > < LF >
1.21 AT ^ DSONSBR: Sub Band Range
| The Command | Possible response (에스) |
| The AT ^ DSONSBR = < 밴드 >, < earfcn_start >, < earfcn_end > [, < 밴드 >, < earfcn_start >, < earfcn_end > [, < 밴드 >, < earfcn_start >, < earfcn_end >]…]. | |
| The AT ^ DSONSBR? | ^ DSONSBR: < 밴드 >, < earfcn_start >, < earfcn_end > [, < 밴드 >, < earfcn_start >, < earfcn_end > [, < 밴드 >, < earfcn_start >, < earfcn_end >]…]. |
| The AT ^ DSONSBR =? | DSONSBR: <밴드>,(list of supported <earfcn>에스), |
<밴드>,(list of supported <earfcn>에스),…
The Description
The execute command is used to configure the frequency range of each subband, save to
NVRAM, and take effect in and out of flight.
The query command is used to query the current subband range configuration.
The test command is used to test whether the command is supported and the range of frequencies allowed to be configured for each subband.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<밴드>: integer type, subband number
64: BAND64
65: BAND65
66: BAND66
<earfcn_start>: integer type, starting frequency, the value range is related to the subband, the value must not be greater than <earfcn_end>
BAND64:24015-24814
BAND65:8060-8259
BAND66:14279-14478
<earfcn_end>: integer type, end frequency point number, the value range is related to the subband, its value cannot be less than <earfcn_start>
BAND64:24015-24814
BAND65:8060-8259
BAND66:14279-14478
예
The AT ^ DSONSBR = 64240, 20248, 00,66,14280,14470 < CR > < LF > < CR > < LF > 승인 < CR >
< LF > the AT ^ DSONSBR?
< CR > < LF > < CR > < LF > ^ DSONSBR: 64240, 20248, 00,66,14280,14470 < CR > < LF > < CR > < LF > 승인 < CR > < LF > the AT ^ DSONSBR =?
< CR > < LF > < CR > < LF > ^ DSONSBR: 64, (24015-24814), 65, (8060-8259), 66,
(14279-14478), 67, (17850-18049), 68, (7580-8029), 69, (14470-14669) < CR > < LF > < CR >
< LF > 승인 < CR > < LF >
1.22 AT ^ APSLEEP: AP SLEEP ENABLE
| The Command | 피ossible response (에스) |
| The AT ^ APSLEEP = < N > | 승인 |
| The AT ^ APSLEEP? | The Error |
| The AT ^ DACS =? | ^ APSLEEP: (list of supported <N>에스) |
The Description
Execute the command to enable AP sleep. Turn on AP sleep by default.N value only supports
1, only supports AP sleep enable function.
Once the command is valid, the AP needs to issue the command again after being awakened to trigger the next sleep.
<N>=1, enabling ap to sleep
<N>= other value, invalid, error returned
The query command is not supported and an error is returned.
The test command is used to test whether the command is supported and to query the value range of the <N> 매개변수.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<N>: integer type to enable ap sleep 1: ...에
예
AT^ APSLEEP =1<CR><LF><CR><LF> 승인 <CR><LF>AT^ APSLEEP?
< CR > < LF > < CR > < LF > + CME ERROR: 100 < CR > < LF > the AT ^ APSLEEP =?
< CR > < LF > < CR > < LF > ^ APSLEEP: (1) < CR > < LF >
1.23. AT^DSONCTX: Continuous wireless signal transmitting
| 명령 | Possible response(에스) |
| AT^DSONCTX =<방법>[,<freq >,<대역폭>,<힘>,<tx_mode>,< single_tone >[,<modu_type>]] | |
| AT^DSONCTX? | ^DSONCTX: <방법>[,<freq >,<대역폭>,<힘>,<tx_mode>,<single_tone>[,<modu_type>]] |
| AT^DSONCTX=? | ^DSONCTX: (list of supported <방법>에스), (list of supported <freq>에스),(list of supported <대역폭>에스), (list of supported < 힘 >에스) ,(list of supported < tx_mode >에스), (list of supported < single_tone>에스), (list of supported < modu_type>에스) |
기술
This instruction is used to indicate whether the node is enabled with the function of long hair. After the function is enabled, the node will continuously send and be full in the time domain and frequency domain of each sub-frame.The command takes effect after being reset.
Final result code
승인
Successful
ERROR or +CME ERROR: <err>
Command performing failed
Defined values
<방법> : integer type, the type of operation to be performed:
0: Turn off long hair function;
1: Enable the function of long hair;
<freq>: integer type, representing the point frequency in 100KHz. Refer to the instruction AT^DSONSBR for the range
<대역폭>: INTEGER type: indicates the bandwidth. For the modulation mode, only 10M\20M is supported. For the single tone mode, 1.4m \3M\5M\10M\20M is supported
Zero: 1.4 엠
1: 3엠
2: 5엠
3: 10엠
4: 15엠(지원되지 않음)
5: 20엠
<힘>: integer Type: indicates the power, expressed in dBm. The value ranges from -40 에게 40. If the power exceeds the maximum value supported by the terminal, the value is the maximum value supported by the terminal.
< tx_mode >:integer type, indicating the sending mode:
0: single antenna;
1: double antenna transmission;
< single_TONE >:integer type, indicating whether it is a single tone. If it is a single tone, modu_type is not set:
0: not monophonic;
1: monophonic;
<modu_type >:integer type, indicating the modulation mode:
QPSK; 0:
16 QAM.
“4 qam;
예
The AT ^ DSONCTX = 0, 5, 1145 “23”, 0, 0, < CR >
<CR><LF>승인<CR><LF>
AT^DSONCTX?<CR>
^ DSONCTX: 1, 14500, 5, “23”, 0, 0
<CR><LF>승인<CR><LF>
AT^DSONCTX=0<CR>
<CR><LF>승인<CR><LF>
AT^DSONCTX =?<CR>
^ DSONCTX: (0 과 1), (14200-15300566-6780), (0 에게 5),
(” – “~ 40” 40 “), (0-1), (0-1), (0, 2)
<CR><LF>승인<CR><LF>
1.24 Typical examples on parameters setting via AT command
예 1: set the uplink and downlink stream ratio
For star wireless network node, it should set the uplink and downlink stream ratio on central node:
AT+CFUN=0 //stop the modem
AT^DSTC=3 //set as Config3 (1D4U)
AT+CFUN=1 //Startup the modem
알아채다: the wireless node version more than 20km distance level only support config0 (2D3U) and Config3 (1D4U); The wireless node version less than 20km distance level support config0 (2D3U), config1 (3D2U), Config2 (4D1U) and Config3 (1D4U).
예 2: set paired password
All of the nodes in the same wireless network should have the same password.
AT+CFUN=0
AT^DAPI=”AEF608AEF608AEF65432″ //set the password as “AEF608AEF608AEF65432”
AT+CFUN=1
예 3: two pairs of wireless node work in a same area
Central node of the first pair wireless node:
AT+CFUN=0
AT^DAOCNDI=04 //04 means 1.4GHz band
AT^DAPI=”11223344″ //set the password as “11223344”
AT^DRPS=,2,”25″ //2 means 5MHz bandwidth, “25” means Tx rf power
AT^ddtc=1 //set as central node
AT^DFHC=0 //disable frequency hopping
AT^DLF=1,14304 //Lock the central working frequency as 1430.4MHz
AT^DSONSSF=2,1 //Disable sleep
AT^DSTC=3 //set the uplink and downlink stream ratio
It need to reboot the node after setting successfully.
Access node of the first pair wireless node:
AT+CFUN=0
AT^DAOCNDI=04
AT^DAPI=”11223344″
AT^DSSMTP=”25″ //set the maximum rf power of the access node
AT^ddtc=2 //set as access node
It need to reboot the node after setting successfully.
Central node of the second pair wireless node:
AT+CFUN=0
AT^DAOCNDI=04 //04 means 1.4GHz band
AT^DAPI=”678123″ //set the password as “678123”
AT^DRPS=,2,”25″ //2 means 5MHz bandwidth, “25” means Tx rf power
AT^ddtc=1 //set as central node
AT^DFHC=0 //disable frequency hopping
AT^DLF=1, 14453 //Lock the central working frequency as 1445.3MHz
AT^DSONSSF=2,1 //Disable sleep
AT^DSTC=3 //set the uplink and downlink stream ratio
It need to reboot the node after setting successfully.
Access node of the second pair wireless node:
AT+CFUN=0
AT^DAOCNDI=04
AT^DAPI=”678123″
AT^DSSMTP=”25″ //set the maximum rf power of the access node
AT^ddtc=2 //set as access node
It need to reboot the node after setting successfully.
예 4: cancel the central working frequency lock
AT+CFUN=0
AT^DLF=0 // cancel the central working frequency lock
AT^DRPS=,5, //5 means 20MHz bandwidth
It need to reboot the node after setting successfully.
예 5: set frequency band
AT+CFUN=0
AT^DSONSBR=65,8060,8259,66,14279,14478,64,24015,24814 //enable three band(800MHz/1400MHz/2400MHz)
AT^DAOCNDI=01 //set to work in 806~825.9MHz
It need to reboot the node after setting successfully.
AT+CFUN=0
AT^DSONSBR=65,8060,8259,66,14279,14478,64,24015,24814 //enable three band(800MHz/1400MHz/2400MHz)
AT^DAOCNDI=04 //set to work in 1427.9~1447.8MHz
It need to reboot the node after setting successfully.
AT+CFUN=0
AT^DSONSBR=65,8060,8259,66,14279,14478,64,24015,24814 //enable three band(800MHz/1400MHz/2400MHz)
AT^DAOCNDI=08 //set to work in 2401.5~2481.4MHz
It need to reboot the node after setting successfully.
AT+CFUN=0
AT^DSONSBR=65,8060,8259,66,14279,14478,64,24015,24814 //enable three band(800MHz/1400MHz/2400MHz)
AT^DAOCNDI=0D //set to work in 806~825.9MHz, 1427.9~1447.8MHz and 2401.5~2481.4MHz
It need to reboot the node after setting successfully.
질문하기
응답해 주셔서 감사합니다. ✨