AT Command Manual
AT-команда может немного отличаться для разных версий модели.. This AT command document is a basic description of the AT command for our modem Model for your reference.
This document applies to these models: км-30км-дальний-беспроводной-видео-передатчик-приемник-передача-приемопередатчик и Вкан1681
Download the TX900 AT command documents PDF
Оглавление
1.1 AT^DACS: Access to the State
| The Command | Possible response (с) |
| The AT ^ DACS = < н > | |
| The AT ^ DACS? | ^ DACS: < н >, < состояние > |
| The AT ^ DACS =? | ^DACS: (list of supported <н>с) |
The Description
The execution command is used to set the switch state of ^DACSI: <состояние> escalation, который
is turned off by default at the beginning of startup. When the setting is turned on, the current state will be reported once.When active report is opened, the access node shall report the indication of access status after successful access;After the central node starts successfully, it can be regarded as a successful access. After determining the type of central node, the access status can be reported.
The query command is used to query the current escalation switch state and the current access state.
The test command is used to test whether the command is supported and to query the value range of the <н> параметр.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<н>: integer type, indicating the active escalation
switch status
0: выключенный
1: на
2: query the current information <состояние>: integer type, indicating the access status
0: not accessed
1: accessed
Пример
The AT ^ DACS = 1 < ЧР > < LF > < ЧР > < LF > ^ DACSI: 0 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > < ЧР > < LF > ^ DACSI: 1 < ЧР > < LF > the AT ^ DACS?
< ЧР > < LF > < ЧР > < LF > ^ DACS: 1, 1 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DACS =?
< ЧР > < LF > < ЧР > < LF > ^ DACS: (0-1) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.2 AT ^ DRPC: Radio Parameter Configure
| The Command | Possible response (с) |
| The AT ^ DRPC = < freq >, < пропускная способность >, < власть > | |
| The AT ^ DRPC? | ^ DRPC: < freq >, < пропускная способность >, < власть > |
| The AT ^ DRPC =? | ^DRPC: (list of supported <freq>с), (list of supported <пропускная способность>с) |
The Description
Execute the command for parameter Settings in the access state and save to NVRAM. The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
ХОРОШО Стыссessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<freq>: integer type, indicating frequency point frequency, unit 100KHz, диапазон
(8060-8259,14279-14478,24015-24814) <пропускная способность>: integer type, indicating bandwidth
0:1.4м
1:3 м
2:5 м
3:10 м
4: 15M (не поддерживается)
5: 20M
<власть>: “целое число” тип, represents the fixed power of the center node, unit dBm, range from “-40” в “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall prevail.
Пример
The AT ^ DRPC = 24415, 1, “27” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DRPC?
< ЧР > < LF > < ЧР > < LF > ^ DRPC: 24415, 1, “27” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DRPC =?
< ЧР > < LF > < ЧР > < LF > ^ DRPC: 15-24814178 (8060-8259142, 79-14478240, 50-18050), (0 в 5) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.3 АТ^ДРПС: Radio Parameter Store in NVRAM
| The Command | Possible response (с) |
| The AT ^ DRPS = < freq >, < пропускная способность >, < власть > | |
| The AT ^ DRPS? | ^ DRPS: < freq >, < пропускная способность >, < власть > |
| The AT ^ DRPS =? | ^DRPS: (list of supported <freq>с), (list of supported <пропускная способность>с) |
The Description
The execute command is used to save parameters to NVRAM, after saving power and restart to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
ХОРОШО Стыссessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<freq>: integer type, indicating frequency point frequency, unit 100KHz, диапазон
(8060-8259,14279-14478,24015-24814) <пропускная способность>: integer type, indicating bandwidth
0:1.4м
1:3 м
2:5 м
3:10 м
4: 15M (не поддерживается)
5: 20M
<власть>: “целое число” тип, represents the fixed power of the center node, unit dBm, range from “-40” в “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall prevail.
Пример
The AT ^ DRPS = 24415, 1, “27” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DRPS?
< ЧР > < LF > < ЧР > < LF > ^ DRPS: 24415, 1, “27” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DRPS =?
< ЧР > < LF > < ЧР > < LF > ^ DRPS: 15-24814178 (8060-8259142, 79-14478240, 50-18050), (0 в 5) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.4 AT^DSSMTP: Set Slave Max Tx Power
| The Command | Possible response (с) |
| The AT ^ DSSMTP = < власть > | |
| The AT ^ DSSMTP? | ^ DSSMTP: < freq >, < пропускная способность >, < власть > |
| The AT ^ DSSMTP =? |
The Description
The execute command is used to save parameters to NVRAM, after saving power and restart to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
ХОРОШО Стыссessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<власть>: “целое число” тип, from the maximum transmitted power of the node, unit dBm, range from “-40” в “40”, and if the maximum value of terminal support is exceeded, the maximum value of terminal support shall be taken as the criterion.
Пример
The AT ^ DSSMTP = “- 10” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DSSMTP?
< ЧР > < LF > < ЧР > < LF > “- 10” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DSSMTP =?
< ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.5 AT ^ DRPR: Radio Parameter Report
| The Command | Possible response (с) |
| The AT ^ DRPR = < н > | |
| The AT ^ DRPR? | ^ DRPR: < н > |
| The AT ^ DRPR =? | ^DRPR: (list of supported <н>с) |
The Description
Execute the command to set the local wireless parameter report ^DRPRI:В < индекс >, <
earfcn >, < cell_id >, < rssi >, < pathloss >, < RSRP >, < RSRQ >, < ОСШ >, < short >, <
tx_power >, < dl_throughput_total_tbs >, < ul_thrpughput_total_tbs >, < dlsch_tb_error_per >,
< the MCS >, < rb_num >, < wide_cqi >, <Dlsch_tb_error_per_total >,< Max_Snr>,< Min_Snr>,< dl_total_tbs_g_rnti > on and off by default.The switch is only valid if the local machine is used as the access node. There is no active escalation for the center node even if the switch is on. The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OK Successful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<н>: integer type, indicating the active escalation switch status 0: выключенный 1: на
2:Query current information <индекс>: integer type, indicating port index no. 1: порт 12: порт
2<earfcn>: integer type, frequency information of measurement result <cell_id>: integer type, cell information of measurement result <rssi>: string type, rssi measurement value,дБм, format as “±value”(кроме “0”)”-141″ в “-44”:RSSI measurements
“+32767”: invalid value <pathloss>: integer type, pathloss,dBm0 to 191: pathloss
32767: invalid value < RSRP >: string type, RSRP measurement value,дБм, format as
“±value”(кроме “0”)”-141″ в “-44”: RSRP measurement value
“+32767”: invalid value < RSRQ >: string type, RSRQ measurement value,дБм, format as “±value”(кроме “0”), the actual value needs to be divided by 10 обработка “-196” в “-30”: RSRQ measurement value
“+32767”: invalid value < ОСШ >: string type,SNR measurement, format as “±value”(кроме
“0”)
“-50” в “+50”: SNR measurement value
“+32767”: invalid value < расстояние >: integer type, distance from the opposite end node, in meters, value range [0, 5000]
< tx_power >:string type, transmitted power, дБм, формат “±value”(кроме “0”) “-50” в “+50”: transmitted power
“+32767”: invalid value < dl_throughput_total_tbs >:integer type, downlink throughput information, sum of TB size in escalation cycle, Байт, диапазон [0,12000000]
< ul_thrpughput_total_tbs >: integer type, upline throughput information, sum of TB size in escalation cycle, Байт, диапазон [0,12000000]
< dlsch_tb_error_per >:integer type, report the percentage of error in the cycle, диапазон [0,100]
< МКС >: МКС, value range [0,29]
<rb_num>: number of RB, value range [6,100]
<wide_cqi>: broadband CQI, value range [1,15]
<dlsch_tb_error_per_total>: report the total error percentage after entering the connection state, диапазон [0,100]
< Max_Snr>: maximum SNR within 10000ms, value range [-40,40]
< Min_Snr>:10000ms minimum SNR, value range [-40,40]
<dl_total_tbs_g_rnti>: integer type, total_tbsize for multicast packets
Пример
The AT ^ DRPR = 1 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DRPR?
< ЧР > < LF > < ЧР > < LF > ^ DRPR: 1 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > < ЧР > < LF > ^ DRPRI: 1100 16й, “- 46”, 20, “60”, “195”, “0”, 4000, “- 36”,
10000000500000,10,15,3,15, 50, “+ 30”, “25”, 15000 < ЧР > < LF > < ЧР > < LF > ^ DRPRI:0 dec, 2100-106 “, 115, “100”, “194”, “+ 20, 4000,” – 36 “, 10000000500000,10,15,3,15, 50, “+
35″, “to 30”, 15000 < ЧР > < LF > the AT ^ DRPR =?
< ЧР > < LF > < ЧР > < LF > ^ DRPR: (0-1) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.6 AT^DAPR: Access Nodes radio Parameter Report
| The Command | Possible response (с) |
| The AT ^ DAPR = < н > | |
| The AT ^ DAPR? | ^ DAPR: < н > |
| The AT ^ DAPR =? | ^DAPR: (list of supported <н>с) |
The Description
Execute the command to set the wireless parameters of the central node to report the access node ^DAPRI: В < IPv6Address >, < the index >, < rssi >, < pathloss >, < RSRP >, < RSRQ >, < ОСШ >, < short >, < tx_power >, < dl_throughput_total_tbs >, < ul_throughput_total_tbs >, < dlsch_tb_error_per >, < dlsch_tb_error_per_total >, < Max_Snr >, < Min_Snr >, < dlThe on-off state of _total_tbs_g_rnti>, turned off by default at startup.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<н>: integer type, indicating the active escalation switch status 0: выключенный 1: на
< 2: query the current information IPv6 address >: string type, has the IP address of the access nodes, is made up of 16 Numbers (0-255), in between each group number. ‘ ‘no, format is: a1, a2, a3, a4, a5, a6, a7, a8.. A9 a10. А11. А12. A13. A14. A15. A16
<индекс>: integer type, indicating port index no. 1: порт 12: port 2<rssi>: string type, rssi measurement value,дБм, format as “±value”(кроме “0”)”-141″ в “-44”: rssi measurement value
“+32767”: invalid value <pathloss>: integer type, pathloss,dBm0 to 191: pathloss
32767: invalid value < RSRP >: string type, RSRP measurement value,дБм, format as
“±value”(кроме “0”)”-141″ в “-44”: RSRP measurement value
“+32767”: invalid value < RSRQ >: string type, RSRQ measurement value,дБм, format as “±value”(кроме “0”), the actual value needs to be divided by 10 обработка “-196” в “-30”: RSRQ measurement value
“+32767”: invalid value < ОСШ >: string type,SNR measurement, format as “±value”(кроме
“0”)
“-50” в “+50”: SNR measurement value
“+32767”: invalid value < расстояние >: integer type, distance from the opposite end node, in meters, value range [0, 5000]
< tx_power >: string type, transmitted power, дБм, формат “±value”(кроме “0”) “-50” в “+50”: transmitted power
“+32767”: invalid value < dl_throughput_total_tbs >: integer type, downlink throughput information, sum of TB size in escalation cycle, Байт, диапазон [0,12000000]
< ul_thrpughput_total_tbs >: integer type, upline throughput information, sum of TB size in escalation cycle, Байт, диапазон [0,12000000]
< dlsch_tb_error_per >: integer type, report the percentage of error in the cycle, диапазон [0,100]
< МКС >: МКС, value range [0,29]
<rb_num>: number of RB, value range [6,100]
<wide_cqi>: broadband CQI, value range [1,15]
<dlsch_tb_error_per_total>: report the total error percentage after entering the connection state, диапазон [0,100]
< Max_Snr>: maximum SNR within 10000ms, value range [-40,40]
< Min_Snr>:10000ms minimum SNR, value range [-40,40]
<dl_total_tbs_g_rnti>: integer type, total_tbsize for multicast packets
Пример
The AT ^ DAPR = 1 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DAPR?
< ЧР > < LF > < ЧР > < LF > ^ DAPR: 1 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > < ЧР > < LF > ^ DAPRI:”1.2.3.4.0.0.0.0.1.2.3.4.200.201.202.203″, 1, “- 46”, 20, “60”, “195”, “0”, 4000, “-
36″, 10000000500000,10,15,3,15, 50, “+ 30”, “25”, 16000 < ЧР > < LF > < ЧР > < LF > ^ DAPRI:”1.2.3.4.0.0.0.0.1.2.3.4.200.201.202.203″, 2, “106”, 115, “100”, “194”, “+ 20, 4000,” –
36 “, 10000000500000,10,15,3,15,50, “+ 35”, “to 30”, 16000 < ЧР > < LF > the AT ^ DAPR =?
< ЧР > < LF > < ЧР > < LF > ^ DAPR: (0-1) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.7 AT^DAOCNDI: Communication Network configuration
| The Command | Possible response (с) |
| The AT ^ DAOCNDI = < band_bitmap > | |
| The AT ^ DAOCNDI? | ^ DAOCNDI: < band_bitmap > |
| The AT ^ DAOCNDI =? |
The Description
The execution command is used to set the operating frequency information of the ad-hoc network communication equipment, and the setting is followed by power-on and power-on. The query command is used to query the operating frequency information of AD hoc network communication equipment.
The test command is used to test whether the command is supported.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<band_bitmap>: string type(without double quotes),in hexadecimal format, the rightmost bit is the least significant bit (LSB/bit0).
Bit0:800 m frequency band
Bit2:1.4 G band
Bit3:2.4 G band
Пример
AT^DAOCNDI=0D<ЧР><LF>// Set band as 800M/ 1.4G / 2.4г <ЧР><LF>ХОРОШО<ЧР><LF> AT^DAOCNDI=01<ЧР><LF>// Set band as 800M<ЧР><LF>ХОРОШО<ЧР><LF>
The AT ^ DAOCNDI?< ЧР > < LF > < ЧР > < LF > ^ DAOCNDI: 0 д < ЧР > < LF > < ЧР > < LF >
ХОРОШО < ЧР > < LF > the AT ^ DAOCNDI =?
< ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.8 AT ^ DDTC: Device Type Configuration
| The Command | Possible response (с) |
| The AT ^ DDTC = < тип > | |
| The AT ^ DDTC? | ^ DDTC: < тип >, < working type > |
| The AT ^ DDTC =? | ^ DDTC: (the list of supported < тип > с) |
The Description
The execute command is used to set the type of AD hoc network communication device, which needs to be set before (+CFUN=1) startup, and takes effect after +CFUN=1 startup.When the type of terminal working equipment is determined, actively report
^DDTCI:<тип>,<working type>
The query command is used to query ad-hoc network communication device type information.
The test command is used to test whether the command is supported.
The Final result code
ХОРОШО Стыссessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<тип>: integer type, indicating the device type
0: авто 1: центральный узел
2: узел доступа <working type>: integer type, indicating the current actual working device type
0: авто
1: центральный узел
2: узел доступа
Пример
The AT ^ DDTC = 0 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
The AT ^ DDTC?< ЧР > < LF > < ЧР > < LF > ^ DDTC: 0, 0 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР >
< LF >
< ЧР > < LF > ^ DDTCI: 0, 1 < ЧР > < LF > the AT ^ DDTC =?
< ЧР > < LF >
< ЧР > < LF > ^ DDTC: (2-0) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.9 AT^DAPI: Access Password ID of Auto Organized Communication
Конфигурация сети
The Command Possible response (с)
| The AT ^ DAPI = < password_id > | |
| The AT ^ DAPI? | ^ DAPI: < password_id > |
| The AT ^ DAPI =? |
The Description
The Settings command is used to set the PASSWORD ID for the ad-hoc networking device. Power on again.
The query command is used to query the PASSWORD ID of the ad-hoc networking device. The test command is used to test whether the command is supported.
The Final result code
ХОРОШО Стыссessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<password_id>: string type, in HEX format, data supports up to 32 байты (HEX string 64 characters)
Пример
The AT ^ fbfa DAPI = “30313233” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
The AT ^ DAPI?< ЧР > < LF > < ЧР > < LF > ^ DAPI: “30313233 fbfa” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DAPI =?
< ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.10 AT ^ DSTC: Set TDD configuration
| The Command | Possible response (с) |
| The AT ^ DSTC = < conf > | |
| The AT ^ DSTC? | ^ DSTC: < the conf > |
| The AT ^ DSTC =? | ^DSTC: (list of supported <conf>с) |
The Description
The execution command is used to set the parameters. После установки, the power down restarts to take effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<conf>: integer type, indicating TDD config setting
0: config0 (2Д3У)
1: конфигурация1 (3Д2У) (remote mode not supported)
2: Конфиг2 (4Д1У) (remote mode not supported)
3: Config3 (1Д4У)
Пример
The AT ^ DSTC = 0 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DSTC?
< ЧР > < LF > < ЧР > < LF > ^ DSTC: 0 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DSTC =?
< ЧР > < LF > < ЧР > < LF > ^ DSTC: (0-3) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР >
< LF >
1.11 AT^DPDBC: PS Data command Configuration
| The Command | Possible response (с) |
| The AT ^ DPDBC = < data_pri >, < dev_name > | |
| The AT ^ DPDBC =? | DPDBC: (range of support <data_pri>с), (range of support <dev_name>с) |
The Description
The execute command is used to set the data hosting priority to the transport port. The setting is valid before starting up.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<data_pri>: integer type, indicating the priority of data-bearing type, начиная от 1 в 3, the smaller the value, the higher the priority
<dev_name>: string type, which represents the transport port name
LMI40: LMI40 device, to be used by 0
LMI41: LMI41 device, to be used by 0
LMI43: LMI43 device, to be used by 1
LMI44: LMI44 device, to be used by 1
UAV_COMM: com-uart communication interface MEDIA0~ MEDAI15: public MEDIA data interface, in which MEDIA0~ MEDAI7 is for use by 0 and MEDIA7~ MEDAI15 is for use by 1
Пример
The AT ^ DPDBC = 1, “LMI40 < ЧР >”
< ЧР > < LF > ХОРОШО < ЧР > < LF > The AT ^ DPDBC =?В < ЧР >
< ЧР > < LF > ^ DPDBC: (1-3), (” LMI40 “, “LMI41”, “LMI43”, “LMI44”, “MEDIA0” ~ “MEDIA15”) < ЧР > < LF >
< ЧР > < LF > ХОРОШО < ЧР > < LF >
1.12 AT^DUBR: UART Baud Rate setting
| The Command | Possible response (с) |
| The AT ^ DUBR = < ставка > | |
| The AT ^ DUBR? | ^ DUBR: < ставка > |
| The AT ^ DUBR =? | DUBR: (list of supported <ставка>с) |
The Description
The execution command is used to set the UART port baud rate parameter, after setting the power down reboot takes effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<ставка>: integer type, represents the UART port baud rate parameter, and the value range is as follows:
1200:1200 byte/s
2400:2400 byte/s
4800:4800 byte/s
9600:9600 byte/s
19200:19200 byte/s
28800:28800 byte/s
38400:38400 byte/s
57600:57600 byte/s
115200:115200 byte/s
Пример
The AT ^ DUBR = 57600 < ЧР >
< ЧР > < LF > ХОРОШО < ЧР > < LF >
The AT ^ DUBR?< ЧР > < LF > < ЧР > < LF > ^ DUBR: 57600 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
The AT ^ DUBR =?В < ЧР >
< ЧР > < LF > ^ DUBR: (1200240 0480 0960 0192 00288 00384 00576 00115 200) < ЧР > < LF >
< ЧР > < LF > ХОРОШО < ЧР > < LF >
1.13 AT^DCIAC: Ciphering and integrityarithmetic Configuration
| The Command | Possible response (с) |
| The AT ^ DCIAC = < arith > | |
| The AT ^ DCIAC? | ^ DCIAC: < arith > |
| The AT ^ DCIAC =? | ^DCIAC: (list of supported <arith>с) |
The Description
The execution command is used to set the encryption and insurance algorithm, after setting the power restart effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
ХОРОШО Стыссessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<arith>: integer type, represents the encryption and completion algorithm, the value range is as follows:
0: none ciphering and integrality
1: СНЕГ
2: the AES
3: ЗУК
Пример
The AT ^ DCIAC = 2 < ЧР >
< ЧР > < LF > ХОРОШО < ЧР > < LF >
The AT ^ DCIAC?< ЧР > < LF > < ЧР > < LF > ^ DCIAC: 2 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР >
< LF >
The AT ^ DCIAC =?В < ЧР >
< ЧР > < LF > ^ DCIAC: (0-3) < ЧР > < LF >
< ЧР > < LF > ХОРОШО < ЧР > < LF >
1.14 AT ^ DFHC: Frequency Hopping Control
| The Command | Possible response (с) |
| The AT ^ DFHC = < н > | |
| The AT ^ DFHC? | ^ DFHC: < н > |
| The AT ^ DFHC =? | ^DFHC: (list of supported <н>с) |
The Description
The execution command is used to set the frequency hopping parameters. После установки, the power down restarts to take effect.
The query command is used to query the current parameter Settings.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
ХОРОШО Стыссessful ERROR or +CME ERROR: <err>Command performing failed
Defined values
<н>: integer type, indicating the frequency hopping function setting 0: turn off the frequency hopping function
1: turn on the frequency hopping function
Пример
The AT ^ DFHC = 0 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DFHC?
< ЧР > < LF > < ЧР > < LF > ^ DFHC: 0 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DFHC =?
< ЧР > < LF > < ЧР > < LF > ^ DFHC: (0-1) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.15 AT ^ LCMFUN Set module functionality
| The Set command The AT ^ LCMFUN = < на > | Set command is used to Set module power on or off. The Response: OK If the error is related to ME functionality: + CME ERROR: 100 The Parameter: < на >: integer of power on or off 0: poweroff 1: poweron 2: poweroff-but not close electric on FLASH/DDR |
| The Read command The AT ^ LCMFUN? | The Response: В < на > OK The Parameter |
| See the set command | |
| The Test command The AT ^ LCMFUN =? | The Response: ^LCMFUN: (list of supported < на >с) OK The Parameter See the set command Пример ^ LCMFUN: (0, 2) ХОРОШО |
| The Reference | |
| Примечание |
1.16 AT ^ POWERCTL Power Ctrl
| The Set Command The AT ^ POWERCTL = < ценить > | Set command is used to reboot OS The Response: OK If the error is related to ME functionality: + CME ERROR: 100 The Parameter: < ценить>: integer of the reboot OS,only one value 1 |
| The Test Command The AT ^ POWERCTL =? | The Response: POWERCTL: (list of supported< vlaue >) OK The Parameter See the set command Example ^ POWERCTL: 1 ХОРОШО |
The Description
The execute command is used to restart the module.
| The Response | The result |
| ХОРОШО | Successful |
| ERROR or +CME ERROR: <err> | The Command performing failed |
Пример
The AT ^ POWERCTL = 1 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.17 AT^DSSMTP: Set Slave Max Tx Power
| The Command | Possible response (с) |
| The AT ^ DSSMTP = < власть > | |
| The AT ^ DSSMTP? | ^ DSSMTP: < власть > |
| The AT ^ DSSMTP =? |
The Description
The execute command is used to save parameters to NVRAM, after saving in and out of flight to take effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<власть>: “целое число” тип, from the maximum transmitted power of the node, unit dBm, range from “-40” в “40”, and if the setting exceeds the maximum supported by the terminal, the maximum supported by the terminal shall be taken as the criterion.
Пример
The AT ^ DSSMTP = “- 10” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT
^ DSSMTP?
< ЧР > < LF > < ЧР > < LF > “- 10” < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
the AT ^ DRPS =?
< ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.18 AT^DSONMCS: Modulation and Coding Scheme Index Set
| The Command | Possible response (с) |
| The AT ^ DSONMCS = < Режим >,, < Mcs > [] | |
| The AT ^ DSONMCS? | ^ DSONMCS: < Режим >, < the Mcs > |
| The AT ^ DSONMCS =? | DSONMCS: (list of supported <Режим>с),(list of supported <Mcs>с) |
The Description
Setting command is used to set MCS index value switch and index value, if not on, is not allowed to change the MCS value; If the MCS switch is turned on, the MCS index value is allowed to be set, effective immediately and saved to NVRAM for permanent effect. The default switch is off.
The query command queries the current set value.
The test command is used to test the Settings that the command supports. NOTE: this instruction can only be issued from the primary node
The Final result code
Хорошо еррy.error or +CME ERROR: <err>Command performing failed.
Defined values
<Режим>: integer type, which represents the function setting of MCS index value. По умолчанию, the setting function is not turned on 0: the setting function is turned off
1: open the setting function
<Mcs>: integer type, indicating the Mcs index value, который варьируется от 0 to 27.The default value is 27
Пример
The AT ^ DSONMCS = 1, 5 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DSONMCS?
< ЧР > < LF > < ЧР > < LF > ^ DSONMCS: 1, 5 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > тот
AT ^ DSONMCS =?
< ЧР > < LF >
< ЧР > < LF > ^ DSONMCS: (0-1), (0-27) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.19 AT ^ DLF: Lock Freq
| The Command | Пossible response (с) |
| The AT ^ DLF = < lock_type > [, < freq >] | |
| The AT ^ DLF? | ^ DLF: < lock_type > [, < freq >] |
| The AT ^ DLF =? | ^DLF: (list of supported<;Lock_type>с), (list of supported lock <freq>с) |
The Description
The execution command is used to control the user to set the lock frequency information, the setting value is saved to NVRAM, and the in-and-out flight takes effect.
The query command is used to query the current parameter Settings in NVRAM.
The test command is used to test whether the command is supported and the value range of the query parameter.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<LockType >: integer type, indicating that the user sets the lock specified frequency switch setting 0: unlocking or unlocking the frequency point
1: lock the specified frequency point
<Freq>: integer type, indicating frequency point frequency, unit 100KHz, диапазон
(8060-8259,14279-14478,24015-248140)
Пример
The AT ^ DLF = 1143 50 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DLF?
< ЧР > < LF > < ЧР > < LF > ^ DLF: 1, 14350 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > тот
AT ^ DLF =?
< ЧР > < LF > < ЧР > < LF > ^ DLF: (0-1), (8060-8259142
79-14478240-15-24814178-50-18050) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.20 AT^DSONSSF: Set Special Function For SON
| Тчасe Command | Пossible response (с) |
| The AT ^ DSONSSF = < FuncType > [, < Ценить >] | |
| The AT ^ DSONSSF? | ^ DSONSSF: < FuncType > [, < Ценить >] |
| The AT ^ DSONSSF =? | DSONSSF: (list of supported (<FuncType>с),(list of supported (<Values>с) |
The Description
The Settings command is used to select and/or set specific functions.AT^DSONSSF=<FuncType> is used to select a particular function, and the result of the selection can be used in the query command.AT^DSONSSF=<FuncType>, и <Ценить> is used to set the Value of a particular function.
The query command returns the current value of the selected function (set by
AT^DSONSSF=<FuncType>).If no function is selected, the default function is returned.
The test command returns the supported value.
The set parameters are stored in NVRAM and take effect on the next power-on.
The Final result code
Okerry.error or +CME ERROR: <err>Command performing failed.
Defined values
<FuncType >: integer type, identifying a specific function
0: send ACK packets in the normal order
1: access to external network
2: the DRX shut down
3. PING and low latency service optimization
4: low power mode
Other value reservation
< Ценить > : an integer type
0: not enabled (контроль)
1: давать возможность (контроль)
Пример
The AT ^ DSONSSF = 0, 1 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DSONSSF?
< ЧР > < LF > < ЧР > < LF > ^ DSONSSF: 0, 1 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > тот
AT ^ DSONSSF =?
< ЧР > < LF > < ЧР > < LF > ^ DSONSSF: (0 в 4), (0-1) < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF >
1.21 AT ^ DSONSBR: Sub Band Range
| The Command | Possible response (с) |
| The AT ^ DSONSBR = < группа >, < earfcn_start >, < earfcn_end > [, < группа >, < earfcn_start >, < earfcn_end > [, < группа >, < earfcn_start >, < earfcn_end >]…]. | |
| The AT ^ DSONSBR? | ^ DSONSBR: < группа >, < earfcn_start >, < earfcn_end > [, < группа >, < earfcn_start >, < earfcn_end > [, < группа >, < earfcn_start >, < earfcn_end >]…]. |
| The AT ^ DSONSBR =? | DSONSBR: <группа>,(list of supported <earfcn>с), |
<группа>,(list of supported <earfcn>с),…
The Description
The execute command is used to configure the frequency range of each subband, save to
NVRAM, and take effect in and out of flight.
The query command is used to query the current subband range configuration.
The test command is used to test whether the command is supported and the range of frequencies allowed to be configured for each subband.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<группа>: integer type, subband number
64: BAND64
65: BAND65
66: BAND66
<earfcn_start>: integer type, starting frequency, the value range is related to the subband, the value must not be greater than <earfcn_end>
BAND64:24015-24814
BAND65:8060-8259
BAND66:14279-14478
<earfcn_end>: integer type, end frequency point number, the value range is related to the subband, its value cannot be less than <earfcn_start>
BAND64:24015-24814
BAND65:8060-8259
BAND66:14279-14478
Пример
The AT ^ DSONSBR = 64240, 20248, 00,66,14280,14470 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР >
< LF > the AT ^ DSONSBR?
< ЧР > < LF > < ЧР > < LF > ^ DSONSBR: 64240, 20248, 00,66,14280,14470 < ЧР > < LF > < ЧР > < LF > ХОРОШО < ЧР > < LF > the AT ^ DSONSBR =?
< ЧР > < LF > < ЧР > < LF > ^ DSONSBR: 64, (24015-24814), 65, (8060-8259), 66,
(14279-14478), 67, (17850-18049), 68, (7580-8029), 69, (14470-14669) < ЧР > < LF > < ЧР >
< LF > ХОРОШО < ЧР > < LF >
1.22 AT ^ APSLEEP: AP SLEEP ENABLE
| The Command | Пossible response (с) |
| The AT ^ APSLEEP = < н > | ХОРОШО |
| The AT ^ APSLEEP? | The Error |
| The AT ^ DACS =? | ^ APSLEEP: (list of supported <н>с) |
The Description
Execute the command to enable AP sleep. Turn on AP sleep by default.N value only supports
1, only supports AP sleep enable function.
Once the command is valid, the AP needs to issue the command again after being awakened to trigger the next sleep.
<н>=1, enabling ap to sleep
<н>= other value, invalid, error returned
The query command is not supported and an error is returned.
The test command is used to test whether the command is supported and to query the value range of the <н> параметр.
The Final result code
OKSuccessfulERROR or +CME ERROR: <err>Command performing failed
Defined values
<н>: integer type to enable ap sleep 1: на
Пример
AT^ APSLEEP =1<ЧР><LF><ЧР><LF> ХОРОШО <ЧР><LF>AT^ APSLEEP?
< ЧР > < LF > < ЧР > < LF > + CME ERROR: 100 < ЧР > < LF > the AT ^ APSLEEP =?
< ЧР > < LF > < ЧР > < LF > ^ APSLEEP: (1) < ЧР > < LF >
1.23. AT^DSONCTX: Continuous wireless signal transmitting
| Команда | Possible response(с) |
| AT^DSONCTX =<режим>[,<freq >,<пропускная способность>,<власть>,<tx_mode>,< single_tone >[,<modu_type>]] | |
| AT^DSONCTX? | ^DSONCTX: <режим>[,<freq >,<пропускная способность>,<власть>,<tx_mode>,<single_tone>[,<modu_type>]] |
| AT^DSONCTX=? | ^DSONCTX: (list of supported <режим>с), (list of supported <freq>с),(list of supported <пропускная способность>с), (list of supported < власть >с) ,(list of supported < tx_mode >с), (list of supported < single_tone>с), (list of supported < modu_type>с) |
Описание
This instruction is used to indicate whether the node is enabled with the function of long hair. After the function is enabled, the node will continuously send and be full in the time domain and frequency domain of each sub-frame.The command takes effect after being reset.
Final result code
ХОРОШО
Successful
ERROR or +CME ERROR: <err>
Command performing failed
Defined values
<режим> : integer type, the type of operation to be performed:
0: Turn off long hair function;
1: Enable the function of long hair;
<freq>: integer type, representing the point frequency in 100KHz. Refer to the instruction AT^DSONSBR for the range
<пропускная способность>: INTEGER type: indicates the bandwidth. For the modulation mode, only 10M\20M is supported. For the single tone mode, 1.4m \3M\5M\10M\20M is supported
Zero: 1.4 M
1: 3M
2: 5M
3: 10M
4: 15M(не поддерживается)
5: 20M
<власть>: integer Type: indicates the power, expressed in dBm. The value ranges from -40 в 40. If the power exceeds the maximum value supported by the terminal, the value is the maximum value supported by the terminal.
< tx_mode >:integer type, indicating the sending mode:
0: single antenna;
1: double antenna transmission;
< single_TONE >:integer type, indicating whether it is a single tone. If it is a single tone, modu_type is not set:
0: not monophonic;
1: monophonic;
<modu_type >:integer type, indicating the modulation mode:
КФСК; 0:
16 QAM.
“4 qam;
Пример
The AT ^ DSONCTX = 0, 5, 1145 “23”, 0, 0, < ЧР >
<ЧР><LF>ХОРОШО<ЧР><LF>
AT^DSONCTX?<ЧР>
^ DSONCTX: 1, 14500, 5, “23”, 0, 0
<ЧР><LF>ХОРОШО<ЧР><LF>
АТ^DSONCTX=0<ЧР>
<ЧР><LF>ХОРОШО<ЧР><LF>
AT^DSONCTX =?<ЧР>
^ DSONCTX: (0 и 1), (14200-15300566-6780), (0 в 5),
(” – “~ 40” 40 “), (0-1), (0-1), (0, 2)
<ЧР><LF>ХОРОШО<ЧР><LF>
1.24 Typical examples on parameters setting via AT command
Пример 1: установить соотношение потоков восходящей и нисходящей линии связи
For star wireless network node, it should set the uplink and downlink stream ratio on central node:
AT+CFUN=0 //stop the modem
AT^DSTC=3 //set as Config3 (1Д4У)
AT+CFUN=1 //Startup the modem
Уведомление: the wireless node version more than 20km distance level only support config0 (2Д3У) и Конфиг3 (1Д4У); The wireless node version less than 20km distance level support config0 (2Д3У), конфигурация1 (3Д2У), Конфиг2 (4Д1У) и Конфиг3 (1Д4У).
Пример 2: set paired password
Все узлы в одной беспроводной сети должны иметь одинаковый пароль..
АТ+CFUN=0
И^ГДЕ=”AEF608AEF608AEF65432″ //set the password as “AEF608AEF608AEF65432”
АТ+CFUN=1
Пример 3: two pairs of wireless node work in a same area
Центральный узел первой пары беспроводных узлов:
АТ+CFUN=0
АТ^DAOCNDI=04 //04 означает диапазон 1,4 ГГц
И^ГДЕ=”11223344″ //установите пароль «11223344»
АТ^ДРПС=,2,”25″ //2 означает полосу пропускания 5 МГц, «25» означает мощность радиочастотной передачи.
AT^ddtc=1 //установить как центральный узел
AT^DFHC=0 //отключаем скачкообразную перестройку частоты
AT^DLF=1,14304 //Зафиксируйте центральную рабочую частоту как 1430,4МГц
AT^DSONSSF=2,1 //Отключить спящий режим
AT^DSTC=3 //устанавливаем соотношение потоков восходящей и нисходящей линии связи
It need to reboot the node after setting successfully.
Узел доступа первой пары беспроводных узлов:
АТ+CFUN=0
АТ^DAOCNDI=04
И^ГДЕ=”11223344″
АТ^ДССМТП=”25″ //установить максимальную радиочастотную мощность узла доступа
AT^ddtc=2 //set as access node
It need to reboot the node after setting successfully.
Central node of the second pair wireless node:
АТ+CFUN=0
АТ^DAOCNDI=04 //04 означает диапазон 1,4 ГГц
И^ГДЕ=”678123″ //установите пароль «678123»
АТ^ДРПС=,2,”25″ //2 означает полосу пропускания 5 МГц, «25» означает мощность радиочастотной передачи.
AT^ddtc=1 //установить как центральный узел
AT^DFHC=0 //отключаем скачкообразную перестройку частоты
АТ^ДЛФ=1, 14453 //Зафиксируйте центральную рабочую частоту как 1445,3 МГц.
AT^DSONSSF=2,1 //Отключить спящий режим
AT^DSTC=3 //устанавливаем соотношение потоков восходящей и нисходящей линии связи
It need to reboot the node after setting successfully.
Access node of the second pair wireless node:
АТ+CFUN=0
АТ^DAOCNDI=04
И^ГДЕ=”678123″
АТ^ДССМТП=”25″ //установить максимальную радиочастотную мощность узла доступа
AT^ddtc=2 //set as access node
It need to reboot the node after setting successfully.
Пример 4: отменить центральную блокировку рабочей частоты
АТ+CFUN=0
AT^DLF=0 // cancel the central working frequency lock
АТ^ДРПС=,5, //5 означает полосу пропускания 20 МГц
It need to reboot the node after setting successfully.
Пример 5: установить полосу частот
АТ+CFUN=0
AT^DSONSBR=65,8060,8259,66,14279,14478,64,24015,24814 //enable three band(800МГц/1400 МГц/2400 МГц)
AT^DAOCNDI=01 //set to work in 806~825.9MHz
It need to reboot the node after setting successfully.
АТ+CFUN=0
AT^DSONSBR=65,8060,8259,66,14279,14478,64,24015,24814 //enable three band(800МГц/1400 МГц/2400 МГц)
AT^DAOCNDI=04 //set to work in 1427.9~1447.8MHz
It need to reboot the node after setting successfully.
АТ+CFUN=0
AT^DSONSBR=65,8060,8259,66,14279,14478,64,24015,24814 //enable three band(800МГц/1400 МГц/2400 МГц)
AT^DAOCNDI=08 //set to work in 2401.5~2481.4MHz
It need to reboot the node after setting successfully.
АТ+CFUN=0
AT^DSONSBR=65,8060,8259,66,14279,14478,64,24015,24814 //enable three band(800МГц/1400 МГц/2400 МГц)
AT^DAOCNDI=0D //set to work in 806~825.9MHz, 1427.9~1447,8МГц и 2401,5~2481,4МГц
It need to reboot the node after setting successfully.
Задайте вопрос
Спасибо за ответ! ✨