SDI or HDMI To IP encoder modulator CVBS H.265 H.264 encoding board pcba Ethernet RSTP UDP for UAV Drone Robotic
$399.00
SDI HDMI To IP encoder modulator CVBS H.265 H.264 encoding board PCBA Ethernet RTSP UDP for UAV Drone Robotic
Daftar isi
pengantar
There are many HDMI encoding boards on the market. Have you met these problems?
- The delay is too long
- The encoding format cannot be customized
- UART AT remote control or operation cannot be used.
- Can not support HDMI and CVBS dual video input encoding
This encoder board supports HDMI, SDI, Masukan video CVBS, dan IP ethernet RJ45 living stream output, most applications are for wireless video transmitters, which can encode the HDMI or CVBS video signal to the digital living stream by H.264 or H.265, and transfer it to the receiver, Konverter CVBS ke IP.
UART software modification can configure the HDMI and Composite CVBS video to the IP ethernet stream encoder modulator module board parameter. Please get in touch with us if you need to customize a similar function to meet your project.
Keuntungan:
Latensi Sangat Rendah
H265 or H264 support
HDMI and CVBS Dual Encoding
Two Audio inputs can switch
Web UI atau port serial perintah UART AT configuration management
- Ultra-low latency H.265/H.264 audio and video encoding maximum support 1080P60 real-time video capture and encoding
- The HDMI or AV input is encoded and outputted to a wireless module through the Ethernet port. The video encoding bit rate can be adjusted dynamically.
- Support audio input and audio decoding output. (Remote operate by UART AT command choose HDMI or CVBS audio)
- You can choose between HDMI or AV encoding for two videos with the option to control the input source using an AT command.
Fitur
The board implements H.265/H.264 audio and video compression encoding, supports up to 1080P@60fps encoding, and is backward compatible with other resolutions and frame rate encoding.
Audio and video input
- Antarmuka HDMI(audio+video):1080 60P,1080 50P,1080 30P,1080 25P,1080 60saya,1080 50saya, 720 60P,720 50P,720 30P, …, various modes adaptive (1080p, 1080Saya, 720p, 1024×768, 1280×1024);
- AV in the interface (audio + video):720×480 60saya(NTSC),720×576 50saya(SAHABAT), mode adaptive. through the AV interface, it can be Line in Mic in.
- The default audio input is the same as the video input interface.
- The audio input interface can also be configured through the Web UI when the serial port detects audio.
- The audio and video source signals are encoded, and the audio and video source acquisition interface can also be configured through the configuration serial port.
- The audio and video source acquisition interface can be dynamically switched through serial port commands during system operation.
Video encoding: H.265 or H.264 format, the encoding bit rate can be configured.
Audio encoding: AAC encoding. - By programming special firmware HDMI+AV the simultaneous capture and encoding of board Audio output(Audio out)
- The board has a built-in audio decoding output function(Line out), which can be connected to an external headphone or audio power amplifier. Audio is decoded and played.
Pelabuhan Ethernet (Ethernet interface)
supports our two-way wireless transmission modulator module, or other third-party two-way links.
Wireless transmission interface( FPC Main interface)
can be connected to our COFDM wireless transmission module, and can also be connected to our two-way wireless transmission link module.
Data-UART
TTL 3.3V level, parameters such as transmission baud rate can be configured. When the board is through a wireless link, the data serial port is used for transparent data transmission.
Kontrol-UART
TTL 3.3V level, which can be connected to our parameter configuration panel or another upper computer to configure the encoding board system.
USB Host interface
software upgrade and maintenance. (optional USB recorder function)
Tegangan catu daya
supports the reverse connection protection of the power input, and supports the power input range of 7~30V. Provides a 5V power output interface. The maximum working power consumption is 2.4W (1080P60 H.265 encoding), and the maximum current is 200mA.
Indicator
indikator daya, video encoding work indicator.
The HDMI to IP encoder board size adalah 70x45x1.2mm (LWH)
The height of the back component is less than 2.5mm, and the height of the front component is less than 6.8mm.
Board weight
20.6 gram.
Interface Signal
- AL (Audio in left), audio input left channel;
-
AR(Audio in right), audio input right channel;
-
GND, signal ground;
-
DARI, analog video input. (Please ignore the color of the wiring, make sure the fourth jack is CVBS Composite video input.)
- HDMI to IP encoder modulator CVBS H.265 H.264 encoding board pcba Ethernet LAN HTTP RTSP UDP onvif TCP IP interface signal 2
Kontrol UART: Equipped with serial port,4PIN 1.25mm pitch socket, TTL 3.3V level, used for the board parameter configuration, can be connected to Sihaida parameter configuration panel or another host computer.
Antarmuka USB:4PIN 1.25mm pitch socket, used for the encoder board software upgrade and maintenance.
Audio-out interface:2PIN 1.25mm pitch socket, the board has a built-in audio decoding output function(Line out), which can be connected to an external headphone or audio power amplifier. Decode and play the audio input from the network port.
Ethernet: Ethernet interface,4PIN 1.25mm pitch socket
Aplikasi
- Done or UAV video encoding
- Robotic or mini-control vehicle
- Unmanned Vehicles UAV
- Unmanned Submarine
- The HDMI to IP board can be COFDM modulation module RCB stacked and assembled with a COFDM one-way transmission module. The connection interface is FPC Main (26PIN flat cable flexible cable interface). HDMI+AV encoder + COFDM Transmitter Module
- The HDMI to IP encoder board PCBA is connected to a two-way wireless link through the network port. Saat ini, the operating parameters can be configured through the network port Web UI. Misalnya, set the video encoding bit rate, H264/H265 encoding method, audio input method, serial port baud rate, dll.
- The board can be connected to the Control-UART parameter configuration panel to set operating parameters.
- HDMI interface version: HDMI V1.4
- Ethernet Output Data rate: 100MBps
- Operating Temperature range: -40~85 degrees
- Compatible Operating System: Embedded Linux
Web UI management Parameter setting
FAQ
This HDMI video to IP encoding board can view the current parameter configuration through the network port Web UI and modify it according to application needs. through the network port browser http://192.168.1.30/ (the IP address of the encoding board)
1. Please check the Web UI from the browser, at the below picture, if the video source input is ok, then it will show the CVBS or HDMI at the red arrow.
2. Please check the HDMI encoding board LED light is blink or not.
If it is green and blink, then the video input source is working well, if not blink, then please check the video input source is ok or not.
The encoding bitrate can be configured. The default web server is set to 0.0 to represent auto (3.12Mbps will be used internally). Customers can modify this value. Misalnya, it is possible to configure 1Mbps~2Mbps or even lower.
1. Large I-frames are prone to frame loss due to wireless transmission;
2. If the gop setting is large, the loss of the I frame will lead to a longer recovery time after the blurred screen;
3. The size difference between I frame and P frame is large, which will increase the transmission delay.
1、比如相机输入1080p60，那gop设置为60/120/180(不建议设置太大)
2、比如相机输入1080p25，那gop设置为25/50/75(不建议设置太大)
3、比如相机输入1080i60，由于需要去交织，所有实际编码是1080p30，那gop设置为30/60/90
从上面可以看到，由于输入相机帧率不确定，所以我们一般建议配置0(Mobil)
cvbs分制式，pal是25fps，ntsc是30fps
假设是pal，那gop设置25/50/75
1、大的I帧容易因为无线传输的原因导致丢帧花屏；
2、gop设置大，I帧丢失导致花屏后恢复时间变长；
3、I帧和P帧大小差别大，会增加传输延迟
Please download at the below link.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
- We can modify the TS stream over UDP, but the TS stream is a non-standard TS stream that we have modified, which needs to be interpreted by our decoder board or special player (Download).
- If you agree with the RTSP protocol, VLC can play it; if you only agree with the TS stream (due to our non-standard modification), VLC cannot decode and play it, so we must use our special player. (Download).
- If you want to switch to the standard MPEG-2 TS stream to play with VLC, our software engineer can customize the firmware for you (this will take a few days) for an additional fee of USD500.
- We use non-standard mpeg-2 ts streams primarily for the following reasons:
- The standard mpeg-2 ts stream has too much overhead outside the effective data, making it unsuitable for use with cofdm;
- The standard mpeg-2 ts stream is difficult to implement the aes encryption function;
- The standard mpeg-2 ts stream is difficult to achieve serial port transparent transmission (used with our decoder board)
- If you don't need our decoder board, encryption and serial port transparent transmission, it is also possible to use standard mpeg-2 ts stream
- It is recommended that you try our player; in real-time performance, our player outperforms vlc.
The vlc player's algorithm does not take into account real-time performance; alih-alih, it will constantly adjust its cache (only increase but not shrink). Sebagai akibat, the longer it is played, the longer the delay may be (especially when used with a wireless link)
1. SSL certificate is HTTPS protocol, our products do not support it now, only HTTP.
2. The default encoder board through the RTSP protocol, RTSP is not encrypted. You can set a longer password. And change it frequently.
3. If you want to encrypt, you need to use a pair of our codec boards (with encoder and decoder board as TX and RX), with UDP protocol, and they are using aes256 encryption. (Just like the bank level.)
iya nih, Tentu, silakan hubungi kami. Let me list your demand at the below.
1. We need to take a composite analog PAL video signal and transmit it using h264 over MPEG2 TS. OKE
2. The output must be playable through VLC. OKE
3. UPD://@1030. OKE
4. The output network stream packet should be 188 bytes standard mpeg2 TS. OKE
5. Compression scheme is h. 264, CVBS PAL input and IP output. OKE
Tentu
Silakan periksa tautan di bawah ini
COFDM UART AT command for the transmitter and Receiver.
Or
Download the COFDM Transmitter UART AT command PDF.
Please follow the checkpoints below to confirm.
- After connecting the encoder board with your computer by ethernet cable, the LED of RJ45 connector should be blinking or not. (to check the ethernet connection is ok or not)
- Is your computer configured with 192.168.1.x network segment ip?
- Have you modified the default IP address of the encoding board? If the IP address changed, maybe you can download and use the below software to find what IP address now.
Or google search LANsee tool software. Download
- Or Directly connect the UART cable of the encoding board to the computer, and use the serial port debugging assistant to send the ATGIP_ command.get ip address command Operation Video at Youtube
Format
ATGIP_
Contoh: ATGIP_
Parameter
TIDAK
Menggunakan
to query the current IP address of the receiving end
Nilai kembalian
Contoh:
ATGIP_
ATGIP192.168.0.215 OK
Komentar
- query command
- More COFDM UART AT commands, please check this link. https://ivcan.com/encoder-modulator-decoder-demodulator-module-parameter/
These parameters are determined by the camera, only the sensor has it.
One more question: In the future is there any possibility to incorporate these features in the output side of encoder (if we get volume orders) ?
Our Answer: These are the parameters of the isp, and our current encoding boards are all bypass isp (because we don't connect the sensor, we don't need and can't use the isp), so we can't add these parameters.
iya nih, CVBS input support NTSC and PAL, Automatic detection and adaptation
- Itu parameter configuration board tool is mainly used for the COFDM module function. If you buy this HDMI / CVBS to IP encoder Vcan1746 separately, you don’t need to buy a parameter configuration board tool, you can adjust the parameters through the Web UI.
- Of course, if you want to use the parameter configuration board tool to adjust some parameters of the encoder board, it is also possible.
- Misalnya, the video encoding bit rate can be configured through the Web UI or changed through the extra parameter configuration board tool. The Web UI can configure all the parameters, and the parameter configuration board tool can only adjust some of them.
Oke, silakan periksa tautan di bawah ini
iya nih, if you need, we can offer you the special firmware to have USB recorder function.
Pertanyaan: Does your USB DVR support playback on the encoded video?
Menjawab: TIDAK, The USB has the record function. You need to play it on a computer, it can not playback on the encoder board directly.
- Do you mean HDMI or AV input, or do you need HDMI and AV to support two simultaneous inputs?
- Currently it supports either HDMI or AV input.
-
Vcan1746 can only choose one of HDMI/AV at present, other boards can meet the firmware you need, but this board only supports SDI + AV/AHD output.
-
If necessary, you can evaluate the board with SDI + AV/AHD input to see if it meets your requirements. Jika ya, our HDMI + AV input Vcan1746 can be made the same later.
-
If you really need to evaluate the HDMI + AV interface, please first buy Vcan746 and burn the default shipping firmware for testing. HDMI and AV can be selected for use. If there is a certain amount of follow-up orders, we can develop a special firmware to support HDMI+AV input at the same time.
-
The display of HDMI and CVBS video input by two channels at the same time is similar to Hikvision IPC, which is divided into main bit rate and sub bit stream. The main stream corresponds to HDMI, and the sub stream corresponds to CVBS.
- Now we can develop a new firmware to support HDMI and CVBS to live streaming at the same time, but the audio can only be selected from one of the two (the system selects HDMI audio/analog audio according to the video access situation).
Didukung.
Our HDMI and CVBS input video encoding board has a USB interface, which can be used for USB recording. It can also be used as the input interface of a USB web camera.
In this way, our video encoding board can convert the signal of your USB web camera into a network interface, while supporting ultra-low latency and supporting h264 and h265 encoding.
Please download the exact dimension size at the below DXF file. (most opened by AutoCAD or DXF viewer software)
https://drive.google.com/file/d/1PAKwv2oBGHYQyul9EMRc5ccbbaU-wp7O/view?usp=drive_link
Q: To clarify, we need HDMI, DARI, and date ports. The date port should be TTL 3.3V.
SEBUAH: No problem, supported.
Q: Is it possible to receive serial data on a computer without a DECODER device?
SEBUAH:
- For the players on the computer, we have RTSP (VLC or Easy player) and UDP (Splayer)
- RTSP protocol only supports audio and video decoding. There is no serial port data decoding.
- UDP (our custom protocol) has audio, video, and serial port transparent transmission data, tapi saat ini, Splayer only decodes the audio and video. If the customer needs serial port transparent transmission data, you must conduct secondary development based on the Splayer. (We can provide Splayer SDK)
- If serial port data is very important for your project, then you also can use our decoder board, which support video, audio, UART serial data.
Q: Now it is working well on the VLC player by RTSP protocol. How can I use UDP at the VLC player?
SEBUAH: UDP is a private and customized protocol. It can only be played at the Splayer.
Q: iya nih, serial data is important to us. We can independently develop a UDP server for serial data if you provide the data format or api.
SEBUAH:
- VLC player or Easyplayer: Obtain audio and video through RTSP streaming by a universal player (VLC player or Easyplayer);
- Special software: Interpret the data stream pushed by the encoding board UDP (including audio and video and serial port transparent transmission data) and get the serial port transparent transmission data from it.
就是客户需要通过两个途径，分别获取音视频流和串口透传数据：
1、通过通用播放器，rtsp拉流获取音视频数据；
2、通过解释编码板udp推送的数据流(含音视频和串口透传数据)，从里面解释出串口透传数据
Q: How can we see that transmitted data is working well?
SEBUAH: Silakan periksa tautan di bawah ini.
how to test data transmission on HDMI to ethernet encoder board?
I will list them:
Regular shipping firmware
- Support HDMI/AV input (you can also connect both and switch through AT commands)
- Support custom protocols and RTSP protocols or Both
- Support H264/H265, support normal delay and low delay mode
- Support USB recording (not turned on by default, you can modify the internal parameters when shipping)
- Support two-way transparent serial port (need to be used with our decoder board)
- Support two-way analog language intercom (need to be used with our decoder board)
Customized firmware
- Support HDMI+AV dual camera input, RTSP access through main/sub stream (similar to IPC)
- Support USB camera/HDMI/AV three-choice input (can be considered as regular shipping firmware with USB camera support added)
- Firmware that supports standard mpegts protocol (not our custom protocol)
Catatan:
- Customized firmware is not the standard shipped firmware. If the customer needs it, it must be replaced with the corresponding firmware when shipping.
- The customized firmware listed above (1~3 points) corresponds to different customized firmware, not one customized firmware that contains all functions.
We also listed in Chinese.
- 支持HDMI/AV二选一输入(也可以都接上，然后通过AT指令切换)
- 支持自定义协议和RTSP协议或者Both
- 支持H264/H265，支持普通延迟和低延迟模式
- 支持U盘录像(默认不打开，可以出货的时候修改内部参数打开)
- 支持双向透传串口(需要搭配我们的解码板使用才有)
- 支持双向模拟语言对讲(需要搭配我们的解码板使用才有)
- 支持HDMI+AV双摄像头输入，RTSP通过主/子码流来访问（类似IPC）
- 支持USB摄像头/HDMI/AV三选一输入(可以认为是常规出货固件增加USB摄像头支持)
- 支持标准mpegts协议(而非我们的自定义协议)的固件
- 定制固件非常规出货固件，如客户需要，出货的时候要更换成对应的固件
- 上面列的定制固件(1~3点)，分别对应不同的定制固件，而非一个定制固件包含所有功能
HDMI Video Sources Input IP Ethernet Output encoder, VLC RTSP operation
Industrial-grade temperature range from -40°C to 70°C Celsius test
Support HDMI and CVBS 2 video streams at the same time
How to get the IP address of the encoder back if you forget
How to test data transmission on HDMI to ethernet encoder board
More FAQ
HS Code
8517629900, Some of our customers use this HS code for your reference.
Special Function Custom Development
-
HDMI and CVBS Dual Video Encoding
-
USB has a video recording function.
-
Special handling of encoding formats to match your custom decoder board
скачать видеокодер
Posting Relatif
- Lower latency HDMI CVBS UVC USB to IP Ethernet RTSP UDP video encoder converter board test by webcam.
- How to upgrade the encoder board firmware?
- How to upgrade the encoder firmware via USB?
- HDMI AV 2 input Video Encoder 2 Stream channels same time.
- How to set gateway ip on the HDMI cvbs to ip video encoder
Papan Modul Encoder
Papan Modul Dekoder
Tersedia untuk Kustomisasi
Produk Encoder Baru
| TIDAK. | nama Produk | Konfigurasi | Fitur Utama | Status |
|---|---|---|---|---|
| 1 | Encoder Video Cahaya Tampak USB UVC Saluran Ganda | 2× masukan USB | Mendukung pengkodean video kamera USB ganda, dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
| 2 | Encoder Saluran Ganda (1× Lampu Tampak USB + 1× Kamera Pencitraan Termal USB) | 2× masukan USB | Mendukung kamera USB ganda (bisa dilihat + panas) menangkap, pengkodean, dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
| 3 | Modul Tampilan HDMI/CVBS Dekoder RTSP | HDMI + keluaran CVBS | Mendukung decoding aliran RTSP hingga 4×1080P@30fps; Mendukung penerusan protokol streaming video; Tampilan keluaran HDMI/CVBS | Sampel Tersedia |
| 4 | Modul Tampilan HDMI/CVBS Dekoder RTSP dengan 4.3"/5" LCD | keluaran HDMI + layar LCD | Mendukung decoding aliran RTSP hingga 4×1080P@30fps; penerusan protokol; Tampilan keluaran HDMI/CVBS | Men-debug |
| 5 | Encoder Saluran Ganda (1× Lampu Tampak USB + 1× CVBS Analog) | 1× CVBS + 1× Masukan UVC USB | Video ganda (USB + CVBS), pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 6 | Encoder Saluran Ganda (1× USB UVC + 1× AHD Analog) | 1× AHD + 1× Masukan UVC USB | Pengambilan video ganda (USB + AHD), pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 7 | Encoder Saluran Ganda (1× CVBS + 1× Video Analog AHD) | CVBS + AHD 2 masukan video | Pengambilan video analog ganda, pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 8 | Encoder Saluran Ganda (1× Kamera CMOS + 1× Kamera Pencitraan Termal USB) | 1× Antarmuka USB | Mendukung CMOS + Pengambilan kamera termal USB, pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
Untuk solusi konversi input/output video khusus yang tidak tercantum dalam produk kami, silakan hubungi kami untuk dukungan OEM/ODM. Kami dapat mengembangkan produk yang disesuaikan berdasarkan kebutuhan Anda.
| input Video | 4K HDMI, HDMI+CVBS, SDI+AHD( atau CVBS) |
|---|
1 ulasan untuk SDI or HDMI To IP encoder modulator CVBS H.265 H.264 encoding board pcba Ethernet RSTP UDP for UAV Drone Robotic
Tambahkan ulasan
SDI or HDMI To IP encoder modulator CVBS H.265 H.264 encoding board pcba Ethernet RSTP UDP for UAV Drone Robotic
$399.00
SDI HDMI To IP encoder modulator CVBS H.265 H.264 encoding board PCBA Ethernet RTSP UDP for UAV Drone Robotic
pengantar
There are many HDMI encoding boards on the market. Have you met these problems?
- The delay is too long
- The encoding format cannot be customized
- UART AT remote control or operation cannot be used.
- Can not support HDMI and CVBS dual video input encoding
This encoder board supports HDMI, SDI, Masukan video CVBS, dan IP ethernet RJ45 living stream output, most applications are for wireless video transmitters, which can encode the HDMI or CVBS video signal to the digital living stream by H.264 or H.265, and transfer it to the receiver, Konverter CVBS ke IP.
UART software modification can configure the HDMI and Composite CVBS video to the IP ethernet stream encoder modulator module board parameter. Please get in touch with us if you need to customize a similar function to meet your project.
Keuntungan:
Latensi Sangat Rendah
H265 or H264 support
HDMI and CVBS Dual Encoding
Two Audio inputs can switch
Web UI atau port serial perintah UART AT configuration management
- Ultra-low latency H.265/H.264 audio and video encoding maximum support 1080P60 real-time video capture and encoding
- The HDMI or AV input is encoded and outputted to a wireless module through the Ethernet port. The video encoding bit rate can be adjusted dynamically.
- Support audio input and audio decoding output. (Remote operate by UART AT command choose HDMI or CVBS audio)
- You can choose between HDMI or AV encoding for two videos with the option to control the input source using an AT command.
Fitur
The board implements H.265/H.264 audio and video compression encoding, supports up to 1080P@60fps encoding, and is backward compatible with other resolutions and frame rate encoding.
Audio and video input
- Antarmuka HDMI(audio+video):1080 60P,1080 50P,1080 30P,1080 25P,1080 60saya,1080 50saya, 720 60P,720 50P,720 30P, …, various modes adaptive (1080p, 1080Saya, 720p, 1024×768, 1280×1024);
- AV in the interface (audio + video):720×480 60saya(NTSC),720×576 50saya(SAHABAT), mode adaptive. through the AV interface, it can be Line in Mic in.
- The default audio input is the same as the video input interface.
- The audio input interface can also be configured through the Web UI when the serial port detects audio.
- The audio and video source signals are encoded, and the audio and video source acquisition interface can also be configured through the configuration serial port.
- The audio and video source acquisition interface can be dynamically switched through serial port commands during system operation.
Video encoding: H.265 or H.264 format, the encoding bit rate can be configured.
Audio encoding: AAC encoding. - By programming special firmware HDMI+AV the simultaneous capture and encoding of board Audio output(Audio out)
- The board has a built-in audio decoding output function(Line out), which can be connected to an external headphone or audio power amplifier. Audio is decoded and played.
Pelabuhan Ethernet (Ethernet interface)
supports our two-way wireless transmission modulator module, or other third-party two-way links.
Wireless transmission interface( FPC Main interface)
can be connected to our COFDM wireless transmission module, and can also be connected to our two-way wireless transmission link module.
Data-UART
TTL 3.3V level, parameters such as transmission baud rate can be configured. When the board is through a wireless link, the data serial port is used for transparent data transmission.
Kontrol-UART
TTL 3.3V level, which can be connected to our parameter configuration panel or another upper computer to configure the encoding board system.
USB Host interface
software upgrade and maintenance. (optional USB recorder function)
Tegangan catu daya
supports the reverse connection protection of the power input, and supports the power input range of 7~30V. Provides a 5V power output interface. The maximum working power consumption is 2.4W (1080P60 H.265 encoding), and the maximum current is 200mA.
Indicator
indikator daya, video encoding work indicator.
The HDMI to IP encoder board size adalah 70x45x1.2mm (LWH)
The height of the back component is less than 2.5mm, and the height of the front component is less than 6.8mm.
Board weight
20.6 gram.
Interface Signal
- AL (Audio in left), audio input left channel;
-
AR(Audio in right), audio input right channel;
-
GND, signal ground;
-
DARI, analog video input. (Please ignore the color of the wiring, make sure the fourth jack is CVBS Composite video input.)
- HDMI to IP encoder modulator CVBS H.265 H.264 encoding board pcba Ethernet LAN HTTP RTSP UDP onvif TCP IP interface signal 2
Kontrol UART: Equipped with serial port,4PIN 1.25mm pitch socket, TTL 3.3V level, used for the board parameter configuration, can be connected to Sihaida parameter configuration panel or another host computer.
Antarmuka USB:4PIN 1.25mm pitch socket, used for the encoder board software upgrade and maintenance.
Audio-out interface:2PIN 1.25mm pitch socket, the board has a built-in audio decoding output function(Line out), which can be connected to an external headphone or audio power amplifier. Decode and play the audio input from the network port.
Ethernet: Ethernet interface,4PIN 1.25mm pitch socket
Aplikasi
- Done or UAV video encoding
- Robotic or mini-control vehicle
- Unmanned Vehicles UAV
- Unmanned Submarine
- The HDMI to IP board can be COFDM modulation module RCB stacked and assembled with a COFDM one-way transmission module. The connection interface is FPC Main (26PIN flat cable flexible cable interface). HDMI+AV encoder + COFDM Transmitter Module
- The HDMI to IP encoder board PCBA is connected to a two-way wireless link through the network port. Saat ini, the operating parameters can be configured through the network port Web UI. Misalnya, set the video encoding bit rate, H264/H265 encoding method, audio input method, serial port baud rate, dll.
- The board can be connected to the Control-UART parameter configuration panel to set operating parameters.
- HDMI interface version: HDMI V1.4
- Ethernet Output Data rate: 100MBps
- Operating Temperature range: -40~85 degrees
- Compatible Operating System: Embedded Linux
Web UI management Parameter setting
FAQ
This HDMI video to IP encoding board can view the current parameter configuration through the network port Web UI and modify it according to application needs. through the network port browser http://192.168.1.30/ (the IP address of the encoding board)
1. Please check the Web UI from the browser, at the below picture, if the video source input is ok, then it will show the CVBS or HDMI at the red arrow.
2. Please check the HDMI encoding board LED light is blink or not.
If it is green and blink, then the video input source is working well, if not blink, then please check the video input source is ok or not.
The encoding bitrate can be configured. The default web server is set to 0.0 to represent auto (3.12Mbps will be used internally). Customers can modify this value. Misalnya, it is possible to configure 1Mbps~2Mbps or even lower.
1. Large I-frames are prone to frame loss due to wireless transmission;
2. If the gop setting is large, the loss of the I frame will lead to a longer recovery time after the blurred screen;
3. The size difference between I frame and P frame is large, which will increase the transmission delay.
1、比如相机输入1080p60，那gop设置为60/120/180(不建议设置太大)
2、比如相机输入1080p25，那gop设置为25/50/75(不建议设置太大)
3、比如相机输入1080i60，由于需要去交织，所有实际编码是1080p30，那gop设置为30/60/90
从上面可以看到，由于输入相机帧率不确定，所以我们一般建议配置0(Mobil)
cvbs分制式，pal是25fps，ntsc是30fps
假设是pal，那gop设置25/50/75
1、大的I帧容易因为无线传输的原因导致丢帧花屏；
2、gop设置大，I帧丢失导致花屏后恢复时间变长；
3、I帧和P帧大小差别大，会增加传输延迟
Please download at the below link.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
- We can modify the TS stream over UDP, but the TS stream is a non-standard TS stream that we have modified, which needs to be interpreted by our decoder board or special player (Download).
- If you agree with the RTSP protocol, VLC can play it; if you only agree with the TS stream (due to our non-standard modification), VLC cannot decode and play it, so we must use our special player. (Download).
- If you want to switch to the standard MPEG-2 TS stream to play with VLC, our software engineer can customize the firmware for you (this will take a few days) for an additional fee of USD500.
- We use non-standard mpeg-2 ts streams primarily for the following reasons:
- The standard mpeg-2 ts stream has too much overhead outside the effective data, making it unsuitable for use with cofdm;
- The standard mpeg-2 ts stream is difficult to implement the aes encryption function;
- The standard mpeg-2 ts stream is difficult to achieve serial port transparent transmission (used with our decoder board)
- If you don't need our decoder board, encryption and serial port transparent transmission, it is also possible to use standard mpeg-2 ts stream
- It is recommended that you try our player; in real-time performance, our player outperforms vlc.
The vlc player's algorithm does not take into account real-time performance; alih-alih, it will constantly adjust its cache (only increase but not shrink). Sebagai akibat, the longer it is played, the longer the delay may be (especially when used with a wireless link)
1. SSL certificate is HTTPS protocol, our products do not support it now, only HTTP.
2. The default encoder board through the RTSP protocol, RTSP is not encrypted. You can set a longer password. And change it frequently.
3. If you want to encrypt, you need to use a pair of our codec boards (with encoder and decoder board as TX and RX), with UDP protocol, and they are using aes256 encryption. (Just like the bank level.)
iya nih, Tentu, silakan hubungi kami. Let me list your demand at the below.
1. We need to take a composite analog PAL video signal and transmit it using h264 over MPEG2 TS. OKE
2. The output must be playable through VLC. OKE
3. UPD://@1030. OKE
4. The output network stream packet should be 188 bytes standard mpeg2 TS. OKE
5. Compression scheme is h. 264, CVBS PAL input and IP output. OKE
Tentu
Silakan periksa tautan di bawah ini
COFDM UART AT command for the transmitter and Receiver.
Or
Download the COFDM Transmitter UART AT command PDF.
Please follow the checkpoints below to confirm.
- After connecting the encoder board with your computer by ethernet cable, the LED of RJ45 connector should be blinking or not. (to check the ethernet connection is ok or not)
- Is your computer configured with 192.168.1.x network segment ip?
- Have you modified the default IP address of the encoding board? If the IP address changed, maybe you can download and use the below software to find what IP address now.
Or google search LANsee tool software. Download
- Or Directly connect the UART cable of the encoding board to the computer, and use the serial port debugging assistant to send the ATGIP_ command.get ip address command Operation Video at Youtube
Format
ATGIP_
Contoh: ATGIP_
Parameter
TIDAK
Menggunakan
to query the current IP address of the receiving end
Nilai kembalian
Contoh:
ATGIP_
ATGIP192.168.0.215 OK
Komentar
- query command
- More COFDM UART AT commands, please check this link. https://ivcan.com/encoder-modulator-decoder-demodulator-module-parameter/
These parameters are determined by the camera, only the sensor has it.
One more question: In the future is there any possibility to incorporate these features in the output side of encoder (if we get volume orders) ?
Our Answer: These are the parameters of the isp, and our current encoding boards are all bypass isp (because we don't connect the sensor, we don't need and can't use the isp), so we can't add these parameters.
iya nih, CVBS input support NTSC and PAL, Automatic detection and adaptation
- Itu parameter configuration board tool is mainly used for the COFDM module function. If you buy this HDMI / CVBS to IP encoder Vcan1746 separately, you don’t need to buy a parameter configuration board tool, you can adjust the parameters through the Web UI.
- Of course, if you want to use the parameter configuration board tool to adjust some parameters of the encoder board, it is also possible.
- Misalnya, the video encoding bit rate can be configured through the Web UI or changed through the extra parameter configuration board tool. The Web UI can configure all the parameters, and the parameter configuration board tool can only adjust some of them.
Oke, silakan periksa tautan di bawah ini
iya nih, if you need, we can offer you the special firmware to have USB recorder function.
Pertanyaan: Does your USB DVR support playback on the encoded video?
Menjawab: TIDAK, The USB has the record function. You need to play it on a computer, it can not playback on the encoder board directly.
- Do you mean HDMI or AV input, or do you need HDMI and AV to support two simultaneous inputs?
- Currently it supports either HDMI or AV input.
-
Vcan1746 can only choose one of HDMI/AV at present, other boards can meet the firmware you need, but this board only supports SDI + AV/AHD output.
-
If necessary, you can evaluate the board with SDI + AV/AHD input to see if it meets your requirements. Jika ya, our HDMI + AV input Vcan1746 can be made the same later.
-
If you really need to evaluate the HDMI + AV interface, please first buy Vcan746 and burn the default shipping firmware for testing. HDMI and AV can be selected for use. If there is a certain amount of follow-up orders, we can develop a special firmware to support HDMI+AV input at the same time.
-
The display of HDMI and CVBS video input by two channels at the same time is similar to Hikvision IPC, which is divided into main bit rate and sub bit stream. The main stream corresponds to HDMI, and the sub stream corresponds to CVBS.
- Now we can develop a new firmware to support HDMI and CVBS to live streaming at the same time, but the audio can only be selected from one of the two (the system selects HDMI audio/analog audio according to the video access situation).
Didukung.
Our HDMI and CVBS input video encoding board has a USB interface, which can be used for USB recording. It can also be used as the input interface of a USB web camera.
In this way, our video encoding board can convert the signal of your USB web camera into a network interface, while supporting ultra-low latency and supporting h264 and h265 encoding.
Please download the exact dimension size at the below DXF file. (most opened by AutoCAD or DXF viewer software)
https://drive.google.com/file/d/1PAKwv2oBGHYQyul9EMRc5ccbbaU-wp7O/view?usp=drive_link
Q: To clarify, we need HDMI, DARI, and date ports. The date port should be TTL 3.3V.
SEBUAH: No problem, supported.
Q: Is it possible to receive serial data on a computer without a DECODER device?
SEBUAH:
- For the players on the computer, we have RTSP (VLC or Easy player) and UDP (Splayer)
- RTSP protocol only supports audio and video decoding. There is no serial port data decoding.
- UDP (our custom protocol) has audio, video, and serial port transparent transmission data, tapi saat ini, Splayer only decodes the audio and video. If the customer needs serial port transparent transmission data, you must conduct secondary development based on the Splayer. (We can provide Splayer SDK)
- If serial port data is very important for your project, then you also can use our decoder board, which support video, audio, UART serial data.
Q: Now it is working well on the VLC player by RTSP protocol. How can I use UDP at the VLC player?
SEBUAH: UDP is a private and customized protocol. It can only be played at the Splayer.
Q: iya nih, serial data is important to us. We can independently develop a UDP server for serial data if you provide the data format or api.
SEBUAH:
- VLC player or Easyplayer: Obtain audio and video through RTSP streaming by a universal player (VLC player or Easyplayer);
- Special software: Interpret the data stream pushed by the encoding board UDP (including audio and video and serial port transparent transmission data) and get the serial port transparent transmission data from it.
就是客户需要通过两个途径，分别获取音视频流和串口透传数据：
1、通过通用播放器，rtsp拉流获取音视频数据；
2、通过解释编码板udp推送的数据流(含音视频和串口透传数据)，从里面解释出串口透传数据
Q: How can we see that transmitted data is working well?
SEBUAH: Silakan periksa tautan di bawah ini.
how to test data transmission on HDMI to ethernet encoder board?
I will list them:
Regular shipping firmware
- Support HDMI/AV input (you can also connect both and switch through AT commands)
- Support custom protocols and RTSP protocols or Both
- Support H264/H265, support normal delay and low delay mode
- Support USB recording (not turned on by default, you can modify the internal parameters when shipping)
- Support two-way transparent serial port (need to be used with our decoder board)
- Support two-way analog language intercom (need to be used with our decoder board)
Customized firmware
- Support HDMI+AV dual camera input, RTSP access through main/sub stream (similar to IPC)
- Support USB camera/HDMI/AV three-choice input (can be considered as regular shipping firmware with USB camera support added)
- Firmware that supports standard mpegts protocol (not our custom protocol)
Catatan:
- Customized firmware is not the standard shipped firmware. If the customer needs it, it must be replaced with the corresponding firmware when shipping.
- The customized firmware listed above (1~3 points) corresponds to different customized firmware, not one customized firmware that contains all functions.
We also listed in Chinese.
- 支持HDMI/AV二选一输入(也可以都接上，然后通过AT指令切换)
- 支持自定义协议和RTSP协议或者Both
- 支持H264/H265，支持普通延迟和低延迟模式
- 支持U盘录像(默认不打开，可以出货的时候修改内部参数打开)
- 支持双向透传串口(需要搭配我们的解码板使用才有)
- 支持双向模拟语言对讲(需要搭配我们的解码板使用才有)
- 支持HDMI+AV双摄像头输入，RTSP通过主/子码流来访问（类似IPC）
- 支持USB摄像头/HDMI/AV三选一输入(可以认为是常规出货固件增加USB摄像头支持)
- 支持标准mpegts协议(而非我们的自定义协议)的固件
- 定制固件非常规出货固件，如客户需要，出货的时候要更换成对应的固件
- 上面列的定制固件(1~3点)，分别对应不同的定制固件，而非一个定制固件包含所有功能
HDMI Video Sources Input IP Ethernet Output encoder, VLC RTSP operation
Industrial-grade temperature range from -40°C to 70°C Celsius test
Support HDMI and CVBS 2 video streams at the same time
How to get the IP address of the encoder back if you forget
How to test data transmission on HDMI to ethernet encoder board
More FAQ
HS Code
8517629900, Some of our customers use this HS code for your reference.
Special Function Custom Development
-
HDMI and CVBS Dual Video Encoding
-
USB has a video recording function.
-
Special handling of encoding formats to match your custom decoder board
скачать видеокодер
Posting Relatif
- Lower latency HDMI CVBS UVC USB to IP Ethernet RTSP UDP video encoder converter board test by webcam.
- How to upgrade the encoder board firmware?
- How to upgrade the encoder firmware via USB?
- HDMI AV 2 input Video Encoder 2 Stream channels same time.
- How to set gateway ip on the HDMI cvbs to ip video encoder
Papan Modul Encoder
Papan Modul Dekoder
Tersedia untuk Kustomisasi
Produk Encoder Baru
| TIDAK. | nama Produk | Konfigurasi | Fitur Utama | Status |
|---|---|---|---|---|
| 1 | Encoder Video Cahaya Tampak USB UVC Saluran Ganda | 2× masukan USB | Mendukung pengkodean video kamera USB ganda, dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
| 2 | Encoder Saluran Ganda (1× Lampu Tampak USB + 1× Kamera Pencitraan Termal USB) | 2× masukan USB | Mendukung kamera USB ganda (bisa dilihat + panas) menangkap, pengkodean, dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
| 3 | Modul Tampilan HDMI/CVBS Dekoder RTSP | HDMI + keluaran CVBS | Mendukung decoding aliran RTSP hingga 4×1080P@30fps; Mendukung penerusan protokol streaming video; Tampilan keluaran HDMI/CVBS | Sampel Tersedia |
| 4 | Modul Tampilan HDMI/CVBS Dekoder RTSP dengan 4.3"/5" LCD | keluaran HDMI + layar LCD | Mendukung decoding aliran RTSP hingga 4×1080P@30fps; penerusan protokol; Tampilan keluaran HDMI/CVBS | Men-debug |
| 5 | Encoder Saluran Ganda (1× Lampu Tampak USB + 1× CVBS Analog) | 1× CVBS + 1× Masukan UVC USB | Video ganda (USB + CVBS), pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 6 | Encoder Saluran Ganda (1× USB UVC + 1× AHD Analog) | 1× AHD + 1× Masukan UVC USB | Pengambilan video ganda (USB + AHD), pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 7 | Encoder Saluran Ganda (1× CVBS + 1× Video Analog AHD) | CVBS + AHD 2 masukan video | Pengambilan video analog ganda, pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 8 | Encoder Saluran Ganda (1× Kamera CMOS + 1× Kamera Pencitraan Termal USB) | 1× Antarmuka USB | Mendukung CMOS + Pengambilan kamera termal USB, pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
Untuk solusi konversi input/output video khusus yang tidak tercantum dalam produk kami, silakan hubungi kami untuk dukungan OEM/ODM. Kami dapat mengembangkan produk yang disesuaikan berdasarkan kebutuhan Anda.
| input Video | 4K HDMI, HDMI+CVBS, SDI+AHD( atau CVBS) |
|---|
1 ulasan untuk SDI or HDMI To IP encoder modulator CVBS H.265 H.264 encoding board pcba Ethernet RSTP UDP for UAV Drone Robotic
Tambahkan ulasan
Daftar isi
What is a CVBS HDMI encoder for live streaming?
CVBS HDMI encoder for live streaming is a device that supports CVBS analog TV composite video input and HDMI 1080P high-definition video input; The board output is IP RJ45 and supports RTSP player and UDP player, which means it connects the board to the internet. Your video sources will become the stream and play on the internet.
FAQ
Q1: Does your CVBS HDMI encoder for live streaming support MPEG-2 TS over UDP supported?
A1: iya nih. Our CVBS HDMI encoder for live streaming supports MPEG-2 TS over UDP.
https://ivcan.com/p/hdmi-to-ip-encoder-modulator-cvbs-h-265-h-264-encoding-board-pcba-ethernet-lan-http-rtsp-udp-onvif-tcp-ip/
Q2: Instead of RSTP, I need an MPEG-2 Transport stream
A2: Do you need DVB-t RF out, which supports the Transport Stream?
Q3: TIDAK, just CVBS input and Ethernet out, Ethernet protocol: H.264. For compression, MPEG-2 TS on UDP broadcast, I need a quote for 5 qty and a complete datasheet.
A3: Vcan1746 can output the TS stream over UDP, but the output TS stream is a non-standard Transport Stream that we have modified, which needs to be interpreted by our decoder board or player.
P5: What should I do if I can’t ping the encoder board from my computer?
Directly connect the UART cable of the encoding board to the computer, and use the serial port debugging assistant to send the ATGIP_ memerintah. Get IP address command Operation Video at Youtube
1. I can get the sub-stream quickly, but the mainstream needs to get it after reboot. What should I do?
I have tested your encoder multiple times with our system. It is working fine overall.
But we have one big issue to validate its usage :
Whenever we turn on the system camera and the encoder at the same time, we cannot read the “mainstream”, we can only read the “sub-stream”.
We have to “Reboot” the encoder via the web interface to make it work: after the reboot, we can directly read the mainstream.
We tried with both VLC and Gstreamer.
What could we try to have both streams readable on startup?
iVcan reply: In the opinion of our engineers, it is either a problem with camera recognition or a problem with customer use.
I suspect that the board card did not recognize the customer’s HDMI camera.
This is easy to verify (if you cannot access the sub-stream, it will be difficult to verify).
Log in to the web server of the encoder board and you can see the camera recognition status on the video page.
The video page will only display the recognition status of one camera. If HDMI and AV cameras are connected and recognized at the same time, the video page will display the recognition status of the HDMI camera (such as 1080p60):
As long as the HDMI camera can recognize it normally, Mainstream can be accessed normally.
If the HDMI camera is not recognized normally, please check the HDMI wiring and power on the board again (note that this is a power cycle, not a software restart on the web page)
Sebagai tambahan, the board uses a random Mac address, so the Mac address will change every time we restart it.
For devices with an ARP cache (such as a PC), after restarting, it will be temporary (a few seconds) unable to access the board from the network. , We cannot access it until the arp request is re-initiated after timeout (the performance is that the coding board cannot be pinged for several seconds after restarting)
Karena itu, I guess another possibility is that when the customer accesses the mainstream, it cannot be accessed due to the above reasons. Then when the customer accesses sub-stream, the arp cache refreshes and the customer can access it, but the customer does not revisit the main-stream.
Whenever we turn on the system camera and the encoder at the same time, we cannot read the “Mainstream”, we can only read the “subStream”.
Judging from your description here, it seems that your camera is started after our encoding board. Please start your camera first, and then power on and start our encoding board to try it. Maybe it is not powered on at the same time. The powered-on order also matters. Misalnya, your camera startup needs 10 detik, but our encoder board startup needs only 5 detik.
Because I am not sure whether your camera is very slow to initialize after power-on.
Because our encoder board starts very quickly, it may be that the camera has not been initialized after it started our encoder board, which may lead to some unexpected problems. This can also explain why “We have to “Reboot” the encoder via the web interface to make it work: after the reboot we can directly read the mainStream.”, because when your web page restarts the encoder board, the camera has already been initialized.
Karena itu, the final suggestions are as follows (I tried my best to list everything that came to mind and let you test them separately);
- Look at the video page of the web server and confirm whether the HDMI camera is recognized normally (you can send a screenshot to us). As long as the camera is recognized normally, Mainstream can be accessed;
- It is recommended that you ping the coding board under cmd first, and then access mainStream and subStream under vlc to avoid mistakenly thinking that Mainstream cannot be accessed due to random mac issues.
- Let you start your camera first (for a few seconds), then power on and start our encoding board to try (see the reasons described above)
- Follow your original operation of “turn on the system camera and the encoder at the same time”. When the problem “we are unable to read the “mainStream”, we can only read the “subStream”.” is reproduced, Do not restart the encoding board through the web page, but hot-swap the HDMI cable between your camera and the encoding board. I think it is only a hot-swap operation (because I suspect it is a plug-in detection problem that causes the camera not to connect to the encoding board. Send HDMI signal)
Produk terkait
CVBS HDMI ke IP Encoder
CVBS HDMI ke IP Encoder
kamera FPV
FPV Analog video scrambler and descrambler module for video encryption and decryption board
CVBS HDMI ke IP Encoder
Papan Modul Encoder
Papan Modul Dekoder
Tersedia untuk Kustomisasi
Produk Encoder Baru
| TIDAK. | nama Produk | Konfigurasi | Fitur Utama | Status |
|---|---|---|---|---|
| 1 | Encoder Video Cahaya Tampak USB UVC Saluran Ganda | 2× masukan USB | Mendukung pengkodean video kamera USB ganda, dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
| 2 | Encoder Saluran Ganda (1× Lampu Tampak USB + 1× Kamera Pencitraan Termal USB) | 2× masukan USB | Mendukung kamera USB ganda (bisa dilihat + panas) menangkap, pengkodean, dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
| 3 | Modul Tampilan HDMI/CVBS Dekoder RTSP | HDMI + keluaran CVBS | Mendukung decoding aliran RTSP hingga 4×1080P@30fps; Mendukung penerusan protokol streaming video; Tampilan keluaran HDMI/CVBS | Sampel Tersedia |
| 4 | Modul Tampilan HDMI/CVBS Dekoder RTSP dengan 4.3"/5" LCD | keluaran HDMI + layar LCD | Mendukung decoding aliran RTSP hingga 4×1080P@30fps; penerusan protokol; Tampilan keluaran HDMI/CVBS | Men-debug |
| 5 | Encoder Saluran Ganda (1× Lampu Tampak USB + 1× CVBS Analog) | 1× CVBS + 1× Masukan UVC USB | Video ganda (USB + CVBS), pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 6 | Encoder Saluran Ganda (1× USB UVC + 1× AHD Analog) | 1× AHD + 1× Masukan UVC USB | Pengambilan video ganda (USB + AHD), pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 7 | Encoder Saluran Ganda (1× CVBS + 1× Video Analog AHD) | CVBS + AHD 2 masukan video | Pengambilan video analog ganda, pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Men-debug |
| 8 | Encoder Saluran Ganda (1× Kamera CMOS + 1× Kamera Pencitraan Termal USB) | 1× Antarmuka USB | Mendukung CMOS + Pengambilan kamera termal USB, pengkodean dan streaming RTSP; keluaran CVBS/HDMI lokal; mode tampilan yang dapat dialihkan | Produksi Massal |
Untuk solusi konversi input/output video khusus yang tidak tercantum dalam produk kami, silakan hubungi kami untuk dukungan OEM/ODM. Kami dapat mengembangkan produk yang disesuaikan berdasarkan kebutuhan Anda.
iVcan.com –
This industrial-grade encoder board is a revelation for our drone operations! It effortlessly converts SDI/HDMI/CVBS feeds into ultra-efficient H.265/H.264 streams over IP with zero lag. The Ethernet/RSTP/UDP support delivers buttery-smooth, low-latency video to our ground station, even during high-speed maneuvers. We’ve tested it across demanding UAV and robotic applications – the rugged PCBA withstands vibrations while maintaining flawless 1080p encoding. Setup was plug-and-play via Ethernet, and the bandwidth savings from H.265 are massive. An absolute essential for reliable aerial telemetry and real-time robotic vision!