HDMI To IP encoder modulator CVBS H.265 H.264 encoding board PCBA Ethernet RTSP UDP for UAV Drone Robotic
Táboa de contidos
introdución
There are many HDMI encoding boards on the market. Have you met these problems?
- The delay is too long
- The encoding format cannot be customized
- UART AT remote control or operation cannot be used.
- Can not support HDMI and CVBS dual video input encoding
This encoder board supports HDMI, SDI, CVBS video input, e IP ethernet RJ45 living stream output, most applications are for wireless video transmitters, which can encode the HDMI or CVBS video signal to the digital living stream by H.264 or H.265, and transfer it to the receiver, Conversor de CVBS a IP.
The HDMI and Composite CVBS video to IP ethernet stream encoder modulator module board parameter can be configured by UART software modification. Please contact us if you need to customize a similar function to meet your project.
vantaxe:
Ultra-Low Latency
H265 or H264 support
HDMI and CVBS Dual Encoding
Two Audio inputs can switch
IU web ou serial port UART AT command configuration management
- Ultra-low latency H.265/H.264 audio and video encoding maximum support 1080P60 real-time video capture and encoding
- The HDMI or AV input is encoded and outputted to a wireless module through the Ethernet port. The video encoding bit rate can be adjusted dynamically.
- Apoiar a entrada e saída de audio desencriptación audio. (Remote operate by UART AT command choose HDMI or CVBS audio)
- You can choose between HDMI or AV encoding for two videos with the option to control the input source using an AT command.
característica
A placa implementa a codificación de compresión de audio e vídeo H.265/H.264, Soporta ata 1080p @ 60fps codificación, and is backward compatible with other resolutions and frame rate encoding.
entrada de audio e vídeo
- Interface HDMI(audio+vídeo):1080 60P,1080 50P,1080 30P,1080 25P,1080 60eu,1080 50eu, 720 60P,720 50P,720 30P, …, varios modos adaptativos (1080p, 1080eu, 720p, 1024×768, 1280×1024);
- AV in the interface (auditivo + vídeo):720×480 60eu(NTSC),720×576 50eu(PAL), modo adaptativo. through the AV interface, it can be Line in Mic in.
- A entrada de audio estándar é a mesma que a interface de entrada de vídeo.
- The audio input interface can also be configured through the Web UI when the serial port detects audio.
- The audio and video source signals are encoded, e a interface de adquisición de fontes de audio e vídeo tamén se pode configurar a través do porto serie de configuración.
- The audio and video source acquisition interface can be dynamically switched through serial port commands during system operation.
codificación de vídeo: formato H.265 ou H.264, pódese configurar a taxa de bits de codificación.
Codificación de audio: Codificación AAC. - Ao programar un firmware especial HDMI+AV, a captura e codificación simultáneas da saída de audio da placa(Saída de audio)
- A placa ten unha función de saída de decodificación de audio incorporada(Liña fóra), que se pode conectar a un auricular externo ou un amplificador de potencia de audio. O audio é decodificado e reproducido.
porto Ethernet (interface Ethernet)
supports our two-way wireless transmission modulator module, ou outras ligazóns bidireccionais de terceiros.
interface de transmisión sen fíos( FPC Main interface)
pódese conectar ao noso módulo de transmisión sen fíos COFDM, e tamén se pode conectar ao noso módulo de enlace de transmisión sen fíos bidireccional.
Data UART
nivel TTL 3.3V, pódense configurar parámetros como a velocidade de transmisión. When the board is through a wireless link, o porto serie de datos úsase para a transmisión de datos transparente.
Control-UART
nivel TTL 3.3V, que se pode conectar ao noso panel de configuración de parámetros ou a outro ordenador superior para configurar o sistema de placas de codificación.
Interface do host USB
actualización e mantemento do software. (optional USB recorder function)
Tensión de alimentación
admite a protección de conexión inversa da entrada de enerxía, and supports the power input range of 7nota de distancia opcional. Ofrece unha interface de saída de enerxía de 5 V. O consumo máximo de enerxía de traballo é de 2,4 W (1080codificación H.265 P60), e a corrente máxima é de 200 mA.
indicador
indicador de alimentación, Indicador de traballo de codificación de vídeo.
The HDMI to IP encoder board size é 70x45x1.2mm (LWH)
A altura do compoñente traseiro é inferior a 2,5 mm, e a altura do compoñente frontal é inferior a 6,8 mm.
peso Board
20.6 gramos.
Sinal de interface
- AL (Audio in left), entrada de audio canle esquerdo;
-
AR(Audio á dereita), entrada de audio canle dereito;
-
GND, terra de sinal;
-
DE, entrada de vídeo analóxico. (Please ignore the color of the wiring, make sure the fourth jack is CVBS Composite video input.)
Control UART: Equipado con porto serie,4Enchufe PIN 1,25 mm, nivel TTL 3.3V, usado para a configuración de parámetros da placa, pódese conectar ao panel de configuración de parámetros Sihaida ou a outro ordenador host.
interfaz USB:4Enchufe PIN 1,25 mm, used for the encoder board software upgrade and maintenance.
Interface de saída de audio:2Enchufe PIN 1,25 mm, o taboleiro ten unha función de saída de decodificación de audio incorporada(Liña fóra), que se pode conectar a un auricular externo ou un amplificador de potencia de audio. Decodifica e reproduce a entrada de audio do porto de rede.
Ethernet: interface Ethernet,4Enchufe PIN 1,25 mm
aplicación
- Done or UAV video encoding
- Robotic or mini-control vehicle
- Unmanned Vehicles UAV
- Unmanned Submarine
- The HDMI to IP board can be COFDM modulation module RCB stacked and assembled with a COFDM one-way transmission module. The connection interface is FPC Main (26Cable plano PIN interfaz de cable flexible). HDMI+AV encoder + COFDM Transmitter Module
- The HDMI to IP encoder board PCBA is connected to a two-way wireless link through the network port. Neste momento, os parámetros de funcionamento pódense configurar a través da IU web do porto de rede. Por exemplo, establecer a taxa de bits de codificación de vídeo, Método de codificación H264/H265, método de entrada de audio, Velocidade en baudios do porto serie, etc.
- The board can be connected to the Control-UART parameter configuration panel to set operating parameters.
- Versión de interface HDMI: HDMI V1.4
- Saída Ethernet Velocidade de datos: 100Cálculo da taxa de transmisión do sistema de transmisión sen fíos COFDM
- Rango de temperatura de funcionamento: -40~85 degrees
- Sistema operativo compatible: Linux incorporado
Web UI management Parameter setting
Preguntas frecuentes
Esta placa de codificación de vídeo HDMI a IP pode ver a configuración actual dos parámetros a través da IU web do porto de rede e modificala segundo as necesidades da aplicación.. a través do navegador de portos de rede http://192.168.1.30/ (o enderezo IP da placa de codificación)
1. Comprobe a IU web desde o navegador, na imaxe de abaixo, se a entrada da fonte de vídeo está ben, then it will show the CVBS or HDMI at the red arrow.
2. Comprobe que a luz LED da placa de codificación HDMI parpadea ou non.
Se é verde e parpadea, entón a fonte de entrada de vídeo funciona ben, se non pestanexa, then please check the video input source is ok or not.
The encoding bitrate can be configured. The default web server is set to 0.0 to represent auto (3.12Mbps will be used internally). Customers can modify this value. Por exemplo, it is possible to configure 1Mbps~2Mbps or even lower.
1. Large I-frames are prone to frame loss due to wireless transmission;
2. If the gop setting is large, the loss of the I frame will lead to a longer recovery time after the blurred screen;
3. The size difference between I frame and P frame is large, which will increase the transmission delay.
1、比如相机输入1080p60,那gop设置为60/120/180(不建议设置太大)
2、比如相机输入1080p25,那gop设置为25/50/75(不建议设置太大)
3、比如相机输入1080i60,由于需要去交织,所有实际编码是1080p30,那gop设置为30/60/90
从上面可以看到,由于输入相机帧率不确定,所以我们一般建议配置0(automático)
cvbs分制式,pal是25fps,ntsc是30fps
假设是pal,那gop设置25/50/75
1、大的I帧容易因为无线传输的原因导致丢帧花屏;
2、gop设置大,I帧丢失导致花屏后恢复时间变长;
3、I帧和P帧大小差别大,会增加传输延迟
Please download at the below link.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
- We can modify the TS stream over UDP, but the TS stream is a non-standard TS stream that we have modified, which needs to be interpreted by our decoder board or special player (Descargar).
- If you agree with the RTSP protocol, VLC can play it; if you only agree with the TS stream (due to our non-standard modification), VLC cannot decode and play it, so we must use our special player. (Descargar).
- If you want to switch to the standard MPEG-2 TS stream to play with VLC, our software engineer can customize the firmware for you (this will take a few days) for an additional fee of USD500.
- We use non-standard mpeg-2 ts streams primarily for the following reasons:
- The standard mpeg-2 ts stream has too much overhead outside the effective data, making it unsuitable for use with cofdm;
- The standard mpeg-2 ts stream is difficult to implement the aes encryption function;
- The standard mpeg-2 ts stream is difficult to achieve serial port transparent transmission (used with our decoder board)
- If you don't need our decoder board, encryption and serial port transparent transmission, it is also possible to use standard mpeg-2 ts stream
- It is recommended that you try our player; in real-time performance, our player outperforms vlc.
The vlc player's algorithm does not take into account real-time performance; en cambio, it will constantly adjust its cache (only increase but not shrink). Como resultado, the longer it is played, the longer the delay may be (especially when used with a wireless link)
1. SSL certificate is HTTPS protocol, our products do not support it now, only HTTP.
2. The default encoder board through the RTSP protocol, RTSP is not encrypted. You can set a longer password. And change it frequently.
3. If you want to encrypt, you need to use a pair of our codec boards (with encoder and decoder board as TX and RX), with UDP protocol, and they are using aes256 encryption. (Just like the bank level.)
si, Claro, póñase en contacto connosco. Let me list your demand at the below.
1. We need to take a composite analog PAL video signal and transmit it using h264 over MPEG2 TS. Ok
2. The output must be playable through VLC. Ok
3. UPD://@1030. Ok
4. The output network stream packet should be 188 bytes standard mpeg2 TS. Ok
5. Compression scheme is h. 264, CVBS PAL input and IP output. Ok
Claro
Consulte a seguinte ligazón
COFDM UART AT command for the transmitter and Receiver.
ou
Descarga o COFDM Transmitter UART AT command PDF.
Please follow the checkpoints below to confirm.
- After connecting the encoder board with your computer by ethernet cable, the LED of RJ45 connector should be blinking or not. (to check the ethernet connection is ok or not)
- Is your computer configured with 192.168.1.x network segment ip?
- Have you modified the default IP address of the encoding board? If the IP address changed, maybe you can download and use the below software to find what IP address now.
- Or Directly connect the UART cable of the encoding board ao ordenador, and use the serial port debugging assistant to send the ATGIP_ command.get ip address command Operation Video at Youtube
formato
ATGIP_
Exemplo: ATGIP_
parámetro
non
uso
to query the current IP address of the receiving end
Valor de retorno
Exemplo:
ATGIP_
ATGIP192.168.0.215 OK
observación
- query command
- More COFDM UART AT commands, consulta esta ligazón. https://ivcan.com/encoder-modulator-decoder-demodulator-module-parameter/
These parameters are determined by the camera, only the sensor has it.
One more question: In the future is there any possibility to incorporate these features in the output side of encoder (if we get volume orders) ?
Our Answer: These are the parameters of the isp, and our current encoding boards are all bypass isp (because we don't connect the sensor, we don't need and can't use the isp), so we can't add these parameters.
si, CVBS input support NTSC and PAL, Automatic detection and adaptation
- o parameter configuration board tool is mainly used for the COFDM module function. If you buy this HDMI / CVBS to IP encoder Vcan1746 separately, you don’t need to buy a parameter configuration board tool, you can adjust the parameters through the Web UI.
- Por suposto, if you want to use the parameter configuration board tool to adjust some parameters of the encoder board, it is also possible.
- Por exemplo, the video encoding bit rate can be configured through the Web UI or changed through the extra parameter configuration board tool. The Web UI can configure all the parameters, and the parameter configuration board tool can only adjust some of them.
Ok, consulte a seguinte ligazón
si, se precisas, we can offer you the special firmware to have USB recorder function.
Pregunta: Does your USB DVR support playback on the encoded video?
resposta: non, The USB has the record function. You need to play it on a computer, it can not playback on the encoder board directly.
- Refírese á entrada HDMI ou AV, ou necesitas HDMI e AV para admitir dúas entradas simultáneas?
- Currently it supports either HDMI or AV input.
-
Vcan1746 can only choose one of HDMI/AV at present, other boards can meet the firmware you need, but this board only supports SDI + AV/AHD output.
-
If necessary, you can evaluate the board with SDI + AV/AHD input to see if it meets your requirements. If yes, our HDMI + AV input Vcan1746 can be made the same later.
-
If you really need to evaluate the HDMI + interface AV, please first buy Vcan746 and burn the default shipping firmware for testing. HDMI and AV can be selected for use. If there is a certain amount of follow-up orders, we can develop a special firmware to support HDMI+AV input at the same time.
-
The display of HDMI and CVBS video input by two channels at the same time is similar to Hikvision IPC, which is divided into main bit rate and sub bit stream. The main stream corresponds to HDMI, and the sub stream corresponds to CVBS.
- Now we can develop a new firmware to support HDMI and CVBS to live streaming at the same time, pero o audio só se pode seleccionar entre un dos dous (o sistema selecciona audio HDMI/audio analóxico segundo a situación de acceso ao vídeo).
Soportado.
Our HDMI and CVBS input video encoding board has a USB interface, which can be used for USB recording. It can also be used as the input interface of a USB web camera.
In this way, our video encoding board can convert the signal of your USB web camera into a network interface, while supporting ultra-low latency and supporting h264 and h265 encoding.
Aínda tes unha pregunta?
Póñase en contacto connosco para obter máis información.
Envía a túa pregunta
HDMI Video Sources Input IP Ethernet Output encoder, VLC RTSP operation
Industrial-grade temperature range from -40°C to 70°C Celsius test
Support HDMI and CVBS 2 video streams at the same time
How to get the IP address of the encoder back if you forget
Máis preguntas frecuentes
HS Code
8517629900, Some of our customers use this HS code for your reference.
Special Function Custom Development
-
HDMI and CVBS Dual Video Encoding
-
USB has a video recording function.
-
Special handling of encoding formats to match your custom decoder board
скачать видеокодер