HDMI To IP encoder modulator CVBS H.265 H.264 encoding board PCBA Ethernet RTSP UDP for UAV Drone Robotic
Obsah
Úvod
There are many HDMI encoding boards on the market. Have you met these problems?
- The delay is too long
- The encoding format cannot be customized
- UART AT remote control or operation cannot be used.
- Can not support HDMI and CVBS dual video input encoding
This encoder board supports HDMI, SDI, CVBS video input, a IP ethernet RJ45 living stream output, most applications are for wireless video transmitters, which can encode the HDMI or CVBS video signal to the digital living stream by H.264 or H.265, and transfer it to the receiver, CVBS to IP converter.
The HDMI and Composite CVBS video to IP ethernet stream encoder modulator module board parameter can be configured by UART software modification. Please contact us if you need to customize a similar function to meet your project.
Výhoda:
Ultra-Low Latency
H265 or H264 support
HDMI and CVBS Dual Encoding
Two Audio inputs can switch
webové uživatelské rozhraní nebo sériový port UART AT příkaz configuration management
- Ultra-low latency H.265/H.264 audio and video encoding maximum support 1080P60 real-time video capture and encoding
- The HDMI or AV input is encoded and outputted to a wireless module through the Ethernet port. The video encoding bit rate can be adjusted dynamically.
- Podporu audio vstup a výstup audio dekódování. (Remote operate by UART AT command choose HDMI or CVBS audio)
- You can choose between HDMI or AV encoding for two videos with the option to control the input source using an AT command.
Vlastnosti
Deska implementuje kódování komprese zvuku a videa H.265/H.264, podporuje až 1080P kódování @ 60 fps, and is backward compatible with other resolutions and frame rate encoding.
Audio a video vstup
- Rozhraní HDMI(audio+video):1080 60P,1080 50P,1080 30P,1080 25P,1080 60já,1080 50já, 720 60P,720 50P,720 30P, …, různé adaptivní režimy (1080p, 1080já, 720p, 1024×768, 1280×1024);
- AV in the interface (Zvuk + video):720×480 60já(NTSC),720×576 50já(KAMARÁD), režim adaptivní. through the AV interface, it can be Line in Mic in.
- Vstupní výchozí zvuk je stejný jako vstupní rozhraní obrazu.
- The audio input interface can also be configured through the Web UI when the serial port detects audio.
- The audio and video source signals are encoded, a rozhraní pro získávání zdrojů zvuku a videa lze také konfigurovat prostřednictvím konfiguračního sériového portu.
- The audio and video source acquisition interface can be dynamically switched through serial port commands during system operation.
kódování videa: H.265 nebo H.264 formát, lze konfigurovat bitovou rychlost kódování.
Kódování zvuku: AAC kódování. - Naprogramováním speciálního firmwaru HDMI+AV současné zachycení a kódování zvukového výstupu desky(Zvukový výstup)
- Deska má vestavěnou funkci výstupu dekódování zvuku(Linka ven), které lze připojit k externím sluchátkům nebo zesilovači zvuku. Zvuk je dekódován a přehráván.
Ethernetový port (rozhraní Ethernet)
supports our two-way wireless transmission modulator module, nebo jiné obousměrné odkazy třetích stran.
Bezdrátový přenos interface( rozhraní FPC_Main)
lze připojit k našemu modulu bezdrátového přenosu COFDM, a lze jej také připojit k našemu modulu obousměrného bezdrátového přenosu.
Data-UART
TTL 3.3V, lze konfigurovat parametry, jako je přenosová rychlost. When the board is through a wireless link, datový sériový port slouží k transparentnímu přenosu dat.
Control-UART
TTL 3.3V, který lze připojit k našemu konfiguračnímu panelu parametrů nebo k jinému nadřazenému počítači pro konfiguraci systému kódovací desky.
Hostitelské rozhraní USB
upgrade a údržba softwaru. (optional USB recorder function)
Napájecí napětí
podporuje ochranu proti zpětnému připojení napájecího vstupu, and supports the power input range of 7~30V. Poskytuje výstupní rozhraní 5V. Maximální pracovní spotřeba je 2,4W (1080kódování P60 H.265), a maximální proud je 200 mA.
Indikátor
signalizace napájení, indikátor práce kódování videa.
The HDMI to IP encoder board size je 70x45x1.2mm (LWH)
Výška zadní části je menší než 2,5 mm, a výška přední součásti je menší než 6,8 mm.
hmotnost Board
20.6 gramů.
Signál rozhraní
- AL (Audio in left), audio vstup levý kanál;
-
AR(Zvuk vpravo), pravý kanál audio vstupu;
-
GND, signálová zem;
-
OF, analogový video vstup. (Please ignore the color of the wiring, make sure the fourth jack is CVBS Composite video input.)
Ovládání UART: Vybaveno sériovým portem,4Zásuvka PIN s roztečí 1,25 mm, TTL 3.3V, používá se pro konfiguraci parametrů desky, lze připojit k konfiguračnímu panelu parametrů Sihaida nebo k jinému hostitelskému počítači.
USB rozhraní:4Zásuvka PIN s roztečí 1,25 mm, used for the encoder board software upgrade and maintenance.
Rozhraní zvukového výstupu:2Zásuvka PIN s roztečí 1,25 mm, deska má vestavěnou funkci výstupu dekódování zvuku(Linka ven), které lze připojit k externím sluchátkům nebo zesilovači zvuku. Dekódujte a přehrajte audio vstup ze síťového portu.
Ethernet: rozhraní Ethernet,4Zásuvka PIN s roztečí 1,25 mm
aplikace
- Done or UAV video encoding
- Robotic or mini-control vehicle
- Unmanned Vehicles UAV
- Unmanned Submarine
- The HDMI to IP board can be COFDM modulation module RCB stacked and assembled with a COFDM one-way transmission module. The connection interface is FPC Main (26Rozhraní flexibilního kabelu s plochým kabelem PIN). HDMI+AV encoder + COFDM Transmitter Module
- The HDMI to IP encoder board PCBA is connected to a two-way wireless link through the network port. V tuto chvíli, provozní parametry lze konfigurovat prostřednictvím webového uživatelského rozhraní síťového portu. Například, nastavit bitovou rychlost kódování videa, Způsob kódování H264/H265, metoda zvukového vstupu, přenosová rychlost sériového portu, atd.
- The board can be connected to the Control-UART parameter configuration panel to set operating parameters.
- Verze rozhraní HDMI: HDMI V1.4
- Ethernetový výstup Přenosová rychlost: 100Středový bod provozní frekvence
- Rozsah provozních teplot: -40~85 degrees
- Kompatibilní operační systém: Vestavěný Linux
Web UI management Parameter setting
Nejčastější dotazy
Tato deska kódování videa HDMI na IP může zobrazit aktuální konfiguraci parametrů prostřednictvím webového uživatelského rozhraní síťového portu a upravit ji podle potřeb aplikace. prostřednictvím prohlížeče síťového portu http://192.168.1.30/ (IP adresa kódovací desky)
1. Zkontrolujte prosím webové uživatelské rozhraní v prohlížeči, na obrázku níže, pokud je vstup zdroje videa v pořádku, pak se zobrazí CVBS nebo HDMI u červené šipky.
2. Zkontrolujte, zda kontrolka LED na desce kódování HDMI bliká nebo nebliká.
Pokud svítí zeleně a bliká, pak zdroj video vstupu funguje dobře, pokud ne blikat, poté zkontrolujte, zda je zdroj vstupu videa v pořádku nebo ne.
Datový tok kódování lze nakonfigurovat. Výchozí webový server je nastaven na 0.0 zastupovat auto (3.12Mb/s bude použito interně). Zákazníci mohou tuto hodnotu upravit. Například, je možné nakonfigurovat 1Mbps~2Mbps nebo dokonce nižší.
1. Large I-frames are prone to frame loss due to wireless transmission;
2. If the gop setting is large, the loss of the I frame will lead to a longer recovery time after the blurred screen;
3. The size difference between I frame and P frame is large, which will increase the transmission delay.
1、比如相机输入1080p60,那gop设置为60/120/180(不建议设置太大)
2、比如相机输入1080p25,Tento gop je nastaven na 25/50/75(不建议设置太大)
3、Například vstup kamery je 1080i60,Kvůli nutnosti prolínání,Všechna skutečná kódování jsou 1080p30,Ten gop je nastaven na 30/60/90
lze vidět shora,Protože snímková frekvence vstupní kamery je nejistá,Obecně tedy doporučujeme nakonfigurovat 0(Auto)
cvbs dělený systém,pal je 25fps,ntsc je 30 snímků za sekundu
Předpokládejme, že je to kamarád,Toto nastavení gop je 25/50/75
1、大的I帧容易因为无线传输的原因导致丢帧花屏;
2、gop设置大,I帧丢失导致花屏后恢复时间变长;
3、I帧和P帧大小差别大,会增加传输延迟
Stáhněte si prosím na níže uvedeném odkazu.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
- We can modify the TS stream over UDP, but the TS stream is a non-standard TS stream that we have modified, which needs to be interpreted by our decoder board or special player (Stažení).
- If you agree with the RTSP protocol, VLC can play it; if you only agree with the TS stream (due to our non-standard modification), VLC cannot decode and play it, so we must use our special player. (Stažení).
- If you want to switch to the standard MPEG-2 TS stream to play with VLC, our software engineer can customize the firmware for you (this will take a few days) for an additional fee of USD500.
- We use non-standard mpeg-2 ts streams primarily for the following reasons:
- The standard mpeg-2 ts stream has too much overhead outside the effective data, making it unsuitable for use with cofdm;
- The standard mpeg-2 ts stream is difficult to implement the aes encryption function;
- The standard mpeg-2 ts stream is difficult to achieve serial port transparent transmission (used with our decoder board)
- If you don't need our decoder board, encryption and serial port transparent transmission, it is also possible to use standard mpeg-2 ts stream
- It is recommended that you try our player; in real-time performance, our player outperforms vlc.
The vlc player's algorithm does not take into account real-time performance; namísto, it will constantly adjust its cache (only increase but not shrink). Jako výsledek, the longer it is played, the longer the delay may be (especially when used with a wireless link)
1. SSL certificate is HTTPS protocol, our products do not support it now, only HTTP.
2. The default encoder board through the RTSP protocol, RTSP is not encrypted. You can set a longer password. And change it frequently.
3. If you want to encrypt, you need to use a pair of our codec boards (with encoder and decoder board as TX and RX), with UDP protocol, and they are using aes256 encryption. (Just like the bank level.)
Ano, Tak určitě, prosím kontaktujte nás. Let me list your demand at the below.
1. We need to take a composite analog PAL video signal and transmit it using h264 over MPEG2 TS. OK
2. The output must be playable through VLC. OK
3. UPD://@1030. OK
4. The output network stream packet should be 188 bytes standard mpeg2 TS. OK
5. Compression scheme is h. 264, CVBS PAL input and IP output. OK
Tak určitě
Zkontrolujte prosím níže uvedený odkaz
COFDM UART AT command for the transmitter and Receiver.
Nebo
Download the COFDM Transmitter UART AT command PDF.
Please follow the checkpoints below to confirm.
- After connecting the encoder board with your computer by ethernet cable, the LED of RJ45 connector should be blinking or not. (to check the ethernet connection is ok or not)
- Is your computer configured with 192.168.1.x network segment ip?
- Have you modified the default IP address of the encoding board? If the IP address changed, maybe you can download and use the below software to find what IP address now.
- Or Directly connect the UART cable of the encoding board do počítače, and use the serial port debugging assistant to send the ATGIP_ command.get ip address command Operation Video at Youtube
Formát
ATGIP_
Example: ATGIP_
Parametr
Ne
Použití
to query the current IP address of the receiving end
Return value
Example:
ATGIP_
ATGIP192.168.0.215 OK
Poznámka
- query command
- More COFDM UART AT commands, please check this link. https://ivcan.com/encoder-modulator-decoder-demodulator-module-parameter/
These parameters are determined by the camera, only the sensor has it.
One more question: In the future is there any possibility to incorporate these features in the output side of encoder (if we get volume orders) ?
Our Answer: These are the parameters of the isp, and our current encoding boards are all bypass isp (because we don't connect the sensor, we don't need and can't use the isp), so we can't add these parameters.
Ano, CVBS input support NTSC and PAL, Automatic detection and adaptation
- The parameter configuration board tool is mainly used for the COFDM module function. If you buy this HDMI / CVBS to IP encoder Vcan1746 separately, you don’t need to buy a parameter configuration board tool, parametry můžete upravit prostřednictvím webového uživatelského rozhraní.
- Samozřejmě, pokud chcete použít nástroj konfigurační desky parametrů k úpravě některých parametrů desky kodéru, je to také možné.
- Například, bitovou rychlost kódování videa lze konfigurovat prostřednictvím webového uživatelského rozhraní nebo změnit pomocí nástroje konfigurační desky zvláštních parametrů. Webové uživatelské rozhraní může konfigurovat všechny parametry, a nástroj konfigurační desky parametrů může upravit pouze některé z nich.
OK, zkontrolujte prosím níže uvedený odkaz
Ano, Pokud potřebuješ, můžeme vám nabídnout speciální firmware pro funkci USB rekordéru.
Otázka: Podporuje váš USB DVR přehrávání kódovaného videa??
Odpovědět: Ne, USB má funkci nahrávání. Musíte to hrát na počítači, nelze přehrávat přímo na desce kodéru.
- Myslíš HDMI nebo AV vstup, nebo potřebujete HDMI a AV pro podporu dvou současných vstupů?
- V současné době podporuje buď HDMI nebo AV vstup.
-
Vcan1746 si v současné době může vybrat pouze jeden z HDMI/AV, ostatní desky mohou splňovat firmware, který potřebujete, ale tato deska podporuje pouze SDI + AV/AHD výstup.
-
Pokud je potřeba, můžete hodnotit desku pomocí SDI + AV/AHD vstup, abyste zjistili, zda splňuje vaše požadavky. Pokud ano, naše HDMI + AV vstup Vcan1746 lze později vyrobit stejně.
-
Pokud opravdu potřebujete zhodnotit HDMI + AV rozhraní, prosím nejprve si zakupte Vcan746 a vypalte výchozí dodávaný firmware pro testování. Pro použití lze vybrat HDMI a AV. If there is a certain amount of follow-up orders, we can develop a special firmware to support HDMI+AV input at the same time.
-
The display of HDMI and CVBS video input by two channels at the same time is similar to Hikvision IPC, which is divided into main bit rate and sub bit stream. The main stream corresponds to HDMI, and the sub stream corresponds to CVBS.
- Now we can develop a new firmware to support HDMI and CVBS to live streaming at the same time, but the audio can only be selected from one of the two (the system selects HDMI audio/analog audio according to the video access situation).
podporován.
Our HDMI and CVBS input video encoding board has a USB interface, which can be used for USB recording. It can also be used as the input interface of a USB web camera.
In this way, our video encoding board can convert the signal of your USB web camera into a network interface, while supporting ultra-low latency and supporting h264 and h265 encoding.
HDMI Video Sources Input IP Ethernet Output encoder, VLC RTSP operation
Industrial-grade temperature range from -40°C to 70°C Celsius test
Support HDMI and CVBS 2 video streams at the same time
How to get the IP address of the encoder back if you forget
Další FAQ
HS Code
8517629900, Some of our customers use this HS code for your reference.
Special Function Custom Development
-
HDMI and CVBS Dual Video Encoding
-
USB has a video recording function.
-
Special handling of encoding formats to match your custom decoder board
скачать видеокодер