Question 1

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 2

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

IP mesh wireless video data audio link module TDD transceiver wireless video transmitter

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 3

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Ethernet Radio Transceiver module with power control for external PA

Question 4

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

15-150km long-range wireless video transmitter and receiver for drone camera

Question 5

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 6

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 7

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 8

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 9

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 10

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 11

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

Question 12

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 13

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 14

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Question 15

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

Question 16

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 17

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 18

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 19

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 20

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 21

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 22

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

Question 23

1. Can you show me this two-way data video link module real product video?

Accepted Answer

Yes, please check the blow video link at the youtube.

Video at Youtube

Question 24

2. Does this model support IP mesh? Is your full duplex link module support for signal relay?

Accepted Answer

This model support customizing the IP mesh function. There are three versions: 3km, 10km, and 50km according to build different the power amplifier.

Normal default full duplex link module support relay, you should buy at least three or more units. One unit is the transmitter, one unit as the receiver, and the other unit can put the middle between the transmitter and receiver as the relay/repeater/extender.

Question 25

3. Can you tell me how to connect your two-way data video link to the RF power amplifier?

Accepted Answer

The maximum RF transmission power of this two-way data video link module is 25±2 dBm, We also provides power amplifier to increase the RF Power to 2W/5W/10W. Below diagram shows how to add power amplifier outside of two-way digital data video link module.

Where is the IIC_SCL pin on the module?

Question 26

4. Can you show me what complete products by this wireless video data link module?

Accepted Answer

Yes, Please check the below link product, which is used the wireless video data audio two-way link module to assemble, just plus the Power ampleifier and encloser and accessory.

TX900

15km 30km 80km 150km long-distance wireless video transmitter receiver transmission transceiver PA 2W 5W 10W

Question 27

5. Can we monitor the module temperature By using web UI?

Accepted Answer

There was no function to query the temperature of the module.

Question 28

6. Can you sell the Morningcore module CX6600 to me? I want to assemble them by myself.

Accepted Answer

Sure. It is ok.
The Moningcore CX6600 (L1860C_P2P) is only an electronics module, you need to develop a peripheral circuit to support it, like power and ethernet and data Input Outport. And you also need to hire a software engineer to develop the firmware and UI for you.
As a trial sample, it is better that you can buy our complete products to test. After you test and use them, the quality is satisfied, then try to buy the module or parts to develop it by yourself. You can copy our design and improve it to be an excellent product.
After all, this is a radio transmission product, and any improper operation may interfere with the signal, resulting in shorter transmission distances.

Question 29

7. Regarding frequency- for testing, we will use 2.4 GHz. However, can we switch frequency bands to 1.4G or 800Mhz later if we change antennas to the right ones? As far as I understand this unit does not have PA.

Accepted Answer

Sure. support.
There is no optional frequency band of 2.4G modification on the web page, you need to send AT commands to modify or enter the Morningcore web page to modify.

Question 30

8. Do you have the exact dimension size? Special the fixing hole size by screw.

Accepted Answer

Question: Any recommendations on the PA + link module enclosure? Need an RF cavity filter? minimal box with cooling for the RF transistor?

Answer: The PA enclosure is CNC according to your design and construction. We used the electronic cooling fan. The encloser is a special CNC produced according to the UAV video data link module + Power Amplifier + cooling fan.

Please check the below picture. Our completed product, TX900, has only a link module + Power Amplifier and cooling fan.

https://i0.wp.com/ivcan.com/wp-content/uploads/2019/09/TDD-Transceiver-Model-T30P-2-watts-PA-power-amplifier.webp

Question 31

9. If I buy just a trial sample without the PA board what range will I get and is it possible to add PA later?

Accepted Answer

What range of the trail sample do you need?
We can offer you a 1~150 km range of the link module. You can add the PA later if you want. Min 15km and max 150km module cost is different.
The module can transfer the signal over 150km with the 10-watt PA to increase the signal. Without the PA, the transmission range is almost 10~15km.
If you buy one 15km range module, even you plus the PA, the range is almost 15~17 km range. The signal strength and ability of the anti-interference will increase much.

Question 32

10. How much current(amps )does the module draw?

Accepted Answer

The Power consumption is about 4W.
Current equals power consumption divided by supply voltage
4 / 12=0.33A, if you’re on a 12-volt supply.

Question 33

11. I need the 150 km transmission range wireless video data module, What frequency range is better?

Accepted Answer

There are two versions on the different frequency range.
1st version’s frequency range is from 1420 Mhz to 1530 Mhz, with 110Mhz frequency width for FHSS.
2nd version’s frequency range is from 806 Mhz to 826 Mhz or 1420 Mhz ~1530 MHz, with only 20Mhz or 40Mhz frequency width for FHSS.
Our engineer recommended that you choose 1st version, as it can supply more frequent points to choose from when the signal is weak or interfered with.

ความถี่	2.4GHz(1เมกะบิตต่อวินาที)	1.4GHz(1เมกะบิตต่อวินาที)	800เมกะเฮิรตซ์(1Mbps)
20Mhz แบนด์วิดธ์	-99dBm	/	/
10Mhz แบนด์วิดธ์	-102dBm	-103dBm	-103dBm
5Mhz แบนด์วิดธ์	-104dBm	-106dBm	-106dBm
3Mhz แบนด์วิดธ์	-106dBm	-108dBm	-108dBm

TTL 3.3V โดยค่าเริ่มต้น	TTL 3.3V โดยค่าเริ่มต้น, ดีซีเข้า:7เกรดระยะทางที่เลือกได้
เกรดระยะทางที่เลือกได้	4ขั้วต่อ PIN ZH1.5mm
เกรดระยะทางที่เลือกได้	เกรดระยะทางที่เลือกได้
ข้อมูล uart1	3ขั้วต่อ PIN ZH1.5mm, TTL 3.3V
ข้อมูล uart2 และ uart3	6ขั้วต่อ PIN PH1.25 มม, uart3 ทำงานเป็นตัวควบคุม uart และ data uart, TTL 3.3V
อินพุตและเอาต์พุตเสียง	4ขั้วต่อ PIN PH1.25 มม
ยูเอสบี	ขั้วต่อไมโคร USB, สำหรับการอัพเกรดซอฟต์แวร์
สวิตช์	สัญญาณควบคุม TX/Rx สำหรับเครื่องขยายสัญญาณเสียงภายนอก
เสาอากาศหลัก	พอร์ตเสาอากาศ TX/Rx, ไอเพ็กซ์
เสาอากาศที่สอง	เกรดระยะทางที่เลือกได้, ไอเพ็กซ์
12วี ออก	ออนบอร์ด 12V ออก(<150mA), สำหรับแหล่งจ่ายไฟพัดลมเย็น
ไฟ LED	สีแดง, ไฟเปิดปกติ
โหนดนำ	สีน้ำเงิน, สว่างขึ้นเมื่อโมดูลตัวรับส่งสัญญาณทำงานเป็นโหนดตัวรับ; กะพริบเมื่อโมดูลตัวรับส่งสัญญาณทำงานเป็นโหนดตัวส่งสัญญาณ
ลิงค์นำ	ไฟดับ - ระบุว่าโหนดไม่ได้เชื่อมโยงกับเครือข่ายไร้สาย; แสงสีแดง - แสดงว่าโหนดเชื่อมต่ออยู่, แต่สัญญาณไร้สายอ่อน; แสงสีส้ม - แสดงว่าโหนดเชื่อมต่ออยู่, สัญญาณไร้สายอยู่ตรงกลาง; ไฟสีเขียว - แสดงว่าโหนดเชื่อมต่ออยู่, สัญญาณไร้สายมีความแรง.

PIN	สัญญาณ	ลักษณะ
เสียงเข้า	เข้าแถวตามค่าเริ่มต้น(ระบุไมค์อิน)	เสียงจะถูกส่งไปยังโมดูลระยะไกลไร้สายเป้าหมาย.
เสียงออก	ไลน์ออก, ขับหูฟัง	เมื่อโหนดได้รับข้อมูลเสียงจากโมดูลไร้สายระยะไกล, เสียงจะเล่นบน PIN นี้.
GND	GND	GND
ควบคุม	ซอฟต์แวร์กำหนด	สวิตช์เปิด/ปิดการควบคุมอินพุตเสียง

ทำงานความถี่	1428~1448MHz หรือ 802~826MHz
แบนด์วิดธ์ช่อง	1.4MHz/3MHz/5MHz/10MHz/20MHz
วิธีการ Modulation	QPSK / QAM16 / QAM64
กำลังส่ง	300mW, 2W, 5W
โหมดเครือข่าย	จุดต่อจุด, เครือข่ายดาวแบบจุดต่อหลายจุด
ระยะการส่ง	อากาศสู่พื้นดิน 15km, 30กม., 50กม., 80กม., 100กม.
ติดต่อข้อมูล	2 พอร์ตเครือข่าย + 1 พอร์ตอนุกรม
อัตราการส่งข้อมูลแบบไร้สาย	สูงสุด 25Mbps, แชร์โดยโหนดทั้งหมดในการส่งแบบสองทาง.
อินเตอร์เฟซที่เสาอากาศ	2 ขั้วต่อ SMA
แหล่งจ่ายไฟ	7วี ~ 30V (แนะนำ 12~28V)
ขนาด	1025221.5มิลลิเมตร (PCBA เท่านั้น)
น้ำหนัก	127 กรัม

27กม. 110กม. NLOS คำถามที่พบบ่อย

ดังสุด ๆ HDMI เวลาแฝงต่ำเป็นพิเศษ คำถามที่พบบ่อย

โมดูลส่งสัญญาณวิดีโอไร้สาย

บอร์ดโมดูล FPV TX RX

CVBS ถึง IP Video Encoder Board

โมดูลลิงค์วิทยุไร้สาย

HDMI ถึง IP ENCODER BOARD

โมดูลตัวรับส่งสัญญาณไร้สายสำหรับข้อมูลวิดีโอ ลิงค์ควบคุม RC ตัวรับส่งสัญญาณแบบสองทิศทาง

สองทาง โมดูลลิงค์วิดีโอข้อมูลดิจิตอลการส่งสัญญาณไร้สาย ดีแอลบี

ลักษณะ

ความไวแสง

อินเตอร์เฟซที่กำหนด

สเปค

คำถามที่พบบ่อย

TX900

ยังมีคำถาม?

คำถามที่พบบ่อยเพิ่มเติม

โพสต์ที่เกี่ยวข้อง

ความคิดเห็น

ข้อความของคุณถูกส่งแล้ว

ข้อความของคุณถูกส่งแล้ว

27กม. 110กม. NLOS คำถามที่พบบ่อย

ดังสุด ๆ HDMI เวลาแฝงต่ำเป็นพิเศษ คำถามที่พบบ่อย

โมดูลส่งสัญญาณวิดีโอไร้สาย

บอร์ดโมดูล FPV TX RX

CVBS ถึง IP Video Encoder Board

โมดูลลิงค์วิทยุไร้สาย

HDMI ถึง IP ENCODER BOARD

โมดูลตัวรับส่งสัญญาณไร้สายสำหรับข้อมูลวิดีโอ ลิงค์ควบคุม RC ตัวรับส่งสัญญาณแบบสองทิศทาง

สองทาง โมดูลลิงค์วิดีโอข้อมูลดิจิตอลการส่งสัญญาณไร้สาย ดีแอลบี

ลักษณะ

ความไวแสง

อินเตอร์เฟซที่กำหนด

สเปค

คำถามที่พบบ่อย

TX900

ยังมีคำถาม?

คำถามที่พบบ่อยเพิ่มเติม

โพสต์ที่เกี่ยวข้อง

ความคิดเห็น

ข้อความของคุณถูกส่งแล้ว

สินค้าที่เกี่ยวข้อง