CVBS ho IP converter, Boto e nyane haholo ea AV Encoder ho tlhahiso ea ethernet, audio ea video e kopaneng, kapa ho fetola khamera ho IP
CVBS ho IP converter, Boto e nyane haholo ea AV Encoder ho tlhahiso ea ethernet, audio ea video e kopaneng, kapa ho fetola khamera ho IP
Tafole ea likateng
mosebetsi
CVBS to IP converter AV encoding board function:
Analog audio and video input, H264 khouto, output through the network port IP ethernet.
Composite CVBS video to IP ethernet converter encoder board
mini Video Encoder Board CVBS input and IP Ethernet output
Support UDP RTSP player VLC
Analogue camera to internet ONVIF TCP IP
Lipatlisiso tsa mahala, Quote ea mahala, Tšehetso ea mahala, Mohlala oa mahala o bonts'a .
Interface
CVBS ho IP converter Refer to the figure above for the encoding module interface and interface signals. The interface description is as follows:
- Analoge mamelwang le video segokanyimmediamentsi sa sebolokigolo input: support analog video input, and audio input(Line Way)。
- Input signal interface(1.25limilimithara spacer) le 13 PIN Toshiba FPC Cable socket multiplexing;
- koung Network: 4PIN 1.25mm spacing base, the base signal, le ea13 PIN Toshiba FPC Cable Socket multiplexing;
- Software protocol: UDP way output.
13Pin Toshiba FPC Pin Define
Ts'ebelisong ea 'nete, you can put off the expansion interface card on the right side of the mini AV board to meet the needs of the structure.
USB segokanyimmediamentsi sa sebolokigolo: Write board firmware, the 4Pin 1.25mm spacing seat can be removed when the structure is installed.
Matching serial port:
4Pin 1.25mm spacing seat, which can connect to our parameter configuration panel board to configure the H264 encoding code rate and other parameters. For details, please refer to the operation description of our parameter configuration panel.
After you change the parameters well, you do not need to change and adapt to the needs of the structure, you can remove the 4-pin seat.
boikhethelo kereiti ea sebaka: 2-pin welding hole, support input voltage range 6 ~ 15V.
CVBS to IP converter board size: 42x37x1.2mm.
The thickness of the board PCB is 1.2mm, the thickness of the maximum device on the back is less than 2mm, and the thickness of the highest front device on the front is less than 5.5mm.
Heating:
The maximum power consumption of the CVBS ho IP converter encoding module is 150mA@12V.
The normal operating temperature range is 0 ℃ ~ 55 ℃ (likhato tsa Celsius).
If it is placed in a small structure for operation for a long time, the CPU needs to be cooled.
FAQs
1. Does it support my low-resolution thermal camera 256x192 on CVBS video?
- CVBS currently only supports the common Pal (720x576) le NTSC (720x480) resolutions.
- Because the interface chip automatically adapts, We guess that our encoder board can not recognize your interface chip with this resolution.
- It is recommended that you connect the thermal imaging camera to an AV monitor or HDMI monitor to see if it can be displayed. If so, although the actual resolution is low, the video stream format may not be this 256x192.
- If it's HDMI, it's possible to modify the software to adapt to your camera; if it's CVBS, I think it's difficult unless you send the camera over and we can debug the software.
- If you need a suitable IR thermal imaging camera, please check our product.
lihlahisoa tse amanang
HDMI ho IP Encoder
Mini Size HDMI Encoder Board Over IP Ethernet RJ45 Output module H.265 HTTP RSTP UDP ONVIF TCP
$199.00
Theko ea pele e ne e: $50.00.$15.00Theko ea hona joale ke: $15.00.