2 Watts kapa 5 Watts kapa 10 watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter

2 Watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter — 2 Watts PA Linear Power Amplifier RF module board PCBA bakeng sa mohalaleli oa sehokelo sa data sa video

Ena ke karolo ea bohlokoa ea transmitter ea video e se nang mohala, e ka holisang lets'oao la RF bakeng sa sebaka se selelele le sebaka se selelele. boikgethelo 1 Watt, 2 Watt, 5 Watt, le 10 Watt.

Tafole ea likateng

Likaroloana

Sehlopha sa maqhubu: 800Mhz-830Mhz, 1425MHz-1455MH
RF ka: 25± 2dBm
RF e felloa ke matla: 2 Watt (33dBm)
- 1400Mhz Transmitter gains 11dB when used with mokhoa oa mekhoa e 'meli oa khokahanyo ea data ea video e se nang mohala, theha matla a phahameng a RF joalo ka 22 ~ 24 dBm, then the RF out power will be 33~35 dBm.
- 800Phaello ea Mhz Transmitter: 13DB, when used with a two-way wireless video data link module, theha matla a phahameng a RF joalo ka 20 ~ 22 dBm, then the RF out power will be 33~35 dBm.
RF e felloa ke matla: 5 Watt (37dBm)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, set up the maximum RF power as 22~25 dBm, then the RF out power will be 37~37 dBm.
- 800Phaello ea Mhz Transmitter: 17DB, when used with a two-way wireless video data link module, theha matla a phahameng a RF joalo ka 20 ~ 22 dBm, then the RF out power will be 37~39 dBm.
RF e felloa ke matla: 10 Watt (40dBm)
- TX leruo la: 18DB, when used with a two-way wireless video data link module, set up the maximum RF power of as 22~24 dBm, then the RF out power will be 40~42dbm.
2 Watts Power in DC12V~16V;
5 Watts Power in DC24V~25V, minimum 1.8A@24V power current rating
10 Watts Power in DC24V~30V, minimum 2.5A@28V power current rating
2 Watts Power consumption: <6The karolelano; 5 Watts Power consumption: <14The karolelano; 10 Watts Power consumption: <28W karolelano
2 Li-Watts 5 Watts PCBA size: 46.5*31limilimithara, botenya ba PCB: 1.2limilimithara
10 Watts Dimensions: 65*62*13.5limilimithara, not including the connector out of the metal housing, Weight: 98g,
Impedance: 50 Ohm

Ho sebetsa hammoho sehokelo sa video sa waelese sa litsela tse peli Module:

How to connect the PA power amplifier with the two way wireless video data link module — Mokhoa oa ho hokela amplifier ea matla ea PA le mojule oa khokahano oa data oa video oa litsela tse peli

RF Keletso

2 Watts PA Linear Power Amplifier RF module board PCBA RF input

Sephetho sa RF

2 Watts PA Linear Power Amplifier RF module board PCBA RF output — 2 Watts PA Linear Power Amplifier RF module board PCBA RF tlhahiso

Wireless Video Transmitter SDI bakeng sa khamera ea nako e telele ea COFDM downlink transmitter	We should solder two bonding pads to connect with power VDD and GND.
Control	We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL le GND). Kenyeletso e phahame (1.8V ho isa ho 3.3V) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode.
RF ka	Sehokelo sa IPEX bakeng sa ho hokahana le antenna ea mantlha ea mojule oa lihokelo tsa data tsa video tse peli.
RF e tsoa	We should solder the bonding pad to an antenna connector.

Housing case and assemble

We recommend that this power amplifier for our two-way wireless video data link OEM PCBA module.

To enhance the power amplifier in conjunction with our two-way wireless video data link module, we recommend you fabricate a metallic housing casing that aligns with your device’s architecture.

It should also leave at least 6mm between the PA board and the upper cover. In order to facilitate heat dissipation and establish an electrical grounding connection, the back side of the PA board must be directly and firmly attached to the metal.

Proper integration of heat dissipation techniques, such as a heat sink or fan, is essential for optimal performance in designs utilizing the PA OEM module.

We can also make a metal chamber for this PA module according to the customer’s requirement.

The below model has a built-in Power Amplifier inside.