COFDM Modulator Demodulator Modul Encoder Decoder HDMI CVBS AV Input AES 256 FHD RF Streaming
Inhaltsverzeechnes
Another side view
COFDM Encoder module, CVBS / HDMI Input, IP output
For More details about the COFDM encoder board, please visit here
COFDM Encoder module Advantage:
- Ultra-niddereg latency H.265 / H.264 Audio a Video Kodéierung maximal Ënnerstëtzung 1080P @ 60 Echtzäit Video Capture a Kodéierung
- HDMI oder AV Audio a Video Input, no Kodéierung, den Ethernet Hafenausgang oder Ausgang op Wireless Modul, Video Kodéierung Bitrate kann dynamesch konfiguréiert ginn
- Ënnerstëtzung Audio Input an Audio decoding Wasserstoff
- Ënnerstëtzt zwee Videoen (HDMI + AV) simultan Input Kodéierung (Optioun, Standard ass HDMI oder AV Kodéierung, wielt een aus zwee Input Sourcing). )
- Web UI oder Serien Hafen UART AT Kommando for configuration management
COFDM transmitter module
COFDM modulator-demodulator datasheet download
COFDM demodulator Vcan1776RX-H264 datasheet
The last version of the TX RX board
Suerge: V6.5.6p
RX: 4.1.2p
FAQs
- Question1: Could you please tell me part number of this component, we try to find localy and check. Äntwert 1: It is a inductance named LOH32PN2R2NNC.
- Suggest Check Points: If the power supply current of the board is well but there is no RF output, maybe the below component TC1-1-13MX+ is generally damaged.
- In order to avoid damage to this device during transportation (the device itself is relatively high), we ordered red glue protection for this device when we shipped it.
- The engineer also suggests that you check to see if the cable is loose or in poor contact.
- Please try to replace the FPC cable connecting the two boards
- We can provide spare parts if you're sure which one.
Sécher
Kuckt w.e.g. de Link hei ënnen.
Encoder Modulator Decoder Demodulator Modul Parameter Configuratioun Uweisungen COFDM AT Kommando
3. Fro, If our camera quality is good enough for both 4 MHz and 8 zréckkomm bandwidth. An dësem Fall, Should the customer choose 4 zréckkomm oder 8 zréckkomm?
Äntwert: Our one-way COFDM shipments use 4Mz wireless bandwidth by default, corresponding to a video bit rate of 3.12Mbps, which is enough for 1080p; If changed to 8MHz wireless bandwidth under the same conditions, the video bit rate doubles to 6.24Mbps. All customers can choose between wireless bandwidth 4MHz and 8MHz, even 6MHz can also be considered.
4. Fro: Which is better for this tx+rx set from a receive sensitivity view?
Äntwert: For wireless links, it can be simply considered that the receiving sensitivity will be higher at lower wireless bandwidths. From the perspective of receiving sensitivity, 4zréckkomm>6zréckkomm>8zréckkomm
Sécher
Kuckt w.e.g. de Link hei ënnen
COFDM Relais Repeater Modul fir Drone UAV Wireless Video Sender an Empfänger Vcan1870
Single channel receiving sensitivity:
-97+/-1dbm at QPSK 8MHz,
-98+/-1dbm at QPSK 6MHZ,
Sensitivity increased by 3dbm when receiving with dual antennas
Jo, Ënnerstëtzung.
COFDM Video encoder modulator transmitter module 3.5G and 4G test result.
The receiver default firmware supports RTSP player, some clients prefer UDP player, which we also can offer, then RTSP player doesn't support. (RTSP and UDP can only choose one of the two firmware)
Download w.e.g. um Link hei ënnen.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
Sécher, kuckt w.e.g. déi ënnescht Foto.
How to switch HDMI or CVBS video input via the UART AT command?
How to upgrade the COFDM video receiver
How to upgrade the COFDM drone video encoder modulator board
Rezensiounen
Et gi keng Kritik nach.