UAV drone video data link modul pemancar dan penerima video nirkabel untuk kamera jarak jauh TDD transceiver dua arah vcan1401

UAV drone video data link module wireless video transmitter and receiver for camera two-way long-range TDD transceiver lightweight

UAV drone video data link Advantage

1. Ukurannya kecil 7.2X4.8X1cm, ringan (less than 60 gram),
2. long-range. Itu omnidirectional fiberglass antenna can reach 30 km. The directional antenna can reach 50KM
3. Pada waktu bersamaan, memiliki 2 bidirectional RS232 serial ports, which are convenient for uploading and uploading data.
4. The minimum delay can reach 28ms (not including the camera recording and monitor displaying time)
5. 20ms excluding monitor and camera. 1080P 60 about 80ms
6. Menggunakan TDD-OFDM transmission protocol, long-range, a large amount of data, free networking, stabil dan tahan lama.
7. Using wide temperature components, it can work normally from -40 degrees to 85 derajat
8. IP67 protection can be used in harsh outdoor environments for a long time.
9. Compared with ordinary bridges, the distance is 10 times that of ordinary WIFI transmission protocols.
10. Multiple power supply redundancy designs, high reliability.
11. They are specifically optimized for video streaming.

Aplikasi

1. Main purpose: Cooperate with IP cameras to transmit video data over long-range.
2. Security monitoring: such as agricultural monitoring, industrial monitoring, factory warehouse monitoring, water monitoring, forest fire prevention, mountain monitoring, dll.
3. Internet of Things: Ad hoc network data transmission.
4. UAV Drones: imagery, transmisi data.
5. Special industry: power station, pemeliharaan air, dll.
6. Public security and armed police firefighting: miniaturized image transmission can be customized. Sebagai contoh, multiple ad hoc network cameras.

Spesifikasi

1. bekerja Frekuensi: kegagalan 1.4G atau 2.3G (2310-2380Mhz）band
2. Bawaan 2 * 1Penguat Daya W
3. Sumber Daya listrik: 7-18V

Connector Input Output

Menetapkan:

kekuatan sinyal	LED P2	LED P3	LED P4
> -70	always	always	always
-71 untuk -75	always	always	-75
-75 untuk -80	mati	always	always
-80 untuk -83	di	-80	dan
-83 untuk -88	always	mati	mati
less than -88	flash	mati	mati
tidak ada sinyal	marquee

5, Port Serial Data, 1.25mm connector, 232 tingkat. (some motherboards only have serial port 1, no serial port 2)

serial number	Fungsi
1	GND
2	5Output V
3	Serial 2 RX
4	Serial 2 TX
5	Serial 1 RX
6	Serial 1 TX

6, 26Pin LNA 0.5mm FPC flexible cable connector, defined as follows:

serial number	fungsi	note
1	5V	Keluaran
2	5V	keluaran
3	NC
4	RF1	RF1 Switch
5	RF2	RF2 Switch
6	ANTD	Antenna Switch
7	NC
8	NC
9	MENGATUR ULANG	MESH firmware reset
10	LNA2_LED
11	LNA1_LED
12	GND
13	12V	12masukan V
14	12V	12masukan V
15	GND
16	RSSI_H	Received Signal Strength Indicator: Kuat
17	RSSI_M	Received Signal Strength Indicator: Medium
18	RSSI_L	Received Signal Strength Indicator: Lemah
19	ANTC	Antenna Switch on/off
20	PA1	Power Amplifier 1 Mengalihkan
21	ANT1	Antena 1 Mengalihkan
22	LAN1_TX_N	Port Jaringan
23	LNA1_TX_P	Port Jaringan
24	GND
25	LNA1_RX_N	Port Jaringan
26	LNA1_RX_P	Port Jaringan

7, Input daya: 7-18V, the positive and negative poles are prohibited to be reversed! Jika tidak, it will be damaged

Please directly weld the wire or weld the XT30 connector. The connector is also marked with positive and negative poles, don’t reverse it!

8, Onboard Pin Network Port:

Pin spacing 1.27mm, 4PIN (This network port can only configure the data of the local device and the other party, and cannot access the data of LAN6 and LAN9)

9, 20PIN 0.5mm FPC flexible cable connector, the definition is as follows: (provided later)

10, port LAN:

1.25mm connector, If it is often plugged and unplugged, it is recommended to externally connect the RJ45 socket with an isolation transformer.

1. LAN-RX-P
2. LAN-RX-N
3. LAN-TX-P
4. LAN-TX-N

11, port LAN: 12PIN interface, PCI-E, and USB interface

12, Fan Interface: GND is ground, 5V outputs 5V, VCC is connected to the main power supply, and the connector is 78172 series

13, Jumper switch:

1. Turn it to the ON position to turn off the RF1 amplifier power.

2. Turn it to the ON position and turn off the power of the RF2 amplifier.

3, not used.

4. Restore the factory settings.

After powering on and entering the system, dial the code to 1 for more than 5 detik, and then dial the code to 0 to restore the factory settings.

Parameter Configuration Tool for Windows Software Download

2.3G-2.4G

1.4G