Placa de codificación para transmisor de vídeo inalámbrico COFDM

Placa de codificación para transmisor de vídeo inalámbrico COFDM

1. Ultra-low latency H.265/H.264 audio and video encoding, maximum support for 1080P@60 real-time audio and video capture encoding
2. Mini HDMI or AV audio and video input, encoded after the Ethernet port output or output to the 矽Hida wireless transmission module, the video encoding rate can be dynamically configured through the serial port
3. Admite entrada de audio y salida de decodificación de audio
4. Supports two channels of video simultaneous input coding (opción)

Característica

This Encode Board implements H.265/H.264 audio and video compression coding, admite codificación de hasta 1080P a 60 fps, and is backward compatible with other various resolution and frame rate encoding.

1. 1. Entrada de audio y vídeo
      1. Miniinterfaz HDMI (audio + video): 1080 60PAG, 1080 50PAG, 1080 30PAG, 1080 25PAG, 1080 60I, 1080 50I, 720 60PAG, 720 50PAG, 720 30PAG, …, varios modos de adaptación;
      2. AV in interface (audio + video): 720×480 60I (NTSC), 720×576 50I (CAMARADA), modo adaptativo. When inputting audio through the AV interface, it can be either Line-in or Microphone in.
      3. After the system is powered on, the audio and video input source is automatically detected. La entrada de audio predeterminada es la misma que la interfaz de entrada de video.. The audio input interface can also be configured through the configuration of the serial port. When the HDMI and AV audio and video sources are connected at the same time, the system preferentially captures the HDMI audio and video source by default. The signal is encoded, and the audio and video source collection interface can also be configured through the configuration serial port, and the audio and video source collection interface can be dynamically switched through the serial port command during system operation.
         Codificación de vídeo: Formato H.265 o H.264, the code rate can be configured through the configuration serial port.
         codificación de audio: AAC coding.
   2. Salida de audio (Speaker interface)
      This Encode board can be connected to the speaker through the Speaker interface to decode and play the input audio when docking the other two-way wireless transmission module RCD or other bidirectional links.
   3. Puerto Ethernet (interfaz ethernet)
      Supports docking with another wireless transmission module, or other two-way wireless links.
   4. Interfaz de transmisión inalámbrica (Interfaz principal FPC)
      It can be connected to the other COFDM wireless transmission module RCA, RCB, etc., and can also be connected to another two-way wireless transmission module RCD.
   5. Puerto serie de datos (Datos-UART)
      Nivel TTL de 3,3 V, transmission baud rate and other parameters can be configured through the configuration of the serial port. When this Encode board is connected to another wireless transmission module, the data serial port is used for one-way transparent data transmission.
   6. Parametric serial port (CFG-UART)
      TTL 3.3V level can be connected to another parameter configuration panel or another host computer, used to configure the operating parameters of this Encode board system. Please contact us for detailed matching agreement.
   7. Interfaz de servidor USB Software upgrade maintenance.
   8. Tensión de alimentación
      Support power supply reverses connection protection, support power input range of 7~24V. Provide a 5V power output interface. The maximum operating power of this Encode board is 2.28W (1080Codificación P60 H.265), and the maximum current is 190mA when the 12V power supply is working.
   9. Indicator light
      Indicador de encendido, video signal detection lock indicator, video coding work indicator.
   10. Tamaño del tablero
       70*45mm (excluding the size of the interface device extending from the edge of the board), the board thickness is 1.2mm, the height of the back component is less than 2mm, and the height of the front component is less than 4mm (when the power input does not use PH2.0 carrier, the power input PH2. 0 seat height is less than 5mm).
   11. Peso de la tabla
       This Encode board weighs 15.5 gramos.

Definición de interfaz

Power and indicator

The power input interface is a 2PIN 2.0mm pitch female. Two pairs of 2PIN power supply holes are reserved on the board. One pair of power supply holes are directly connected to the power input signal, and the other pair of power supply holes are exposed after anti-reverse protection. This Encode board also provides a 5V power output interface, which is convenient for the user to supply power to the cooling fan when needed. The figure below shows the power pin signals and indicators.

LED1: Power operation indicator, always on after power-on;
LED2: Video signal detection lock indicator light, this Encode board will automatically lock after detecting the video source. If the LED is not lit, the system fails to collect the video source.
LED3: Video coding work indicator, flashing during normal operation.

Interfaz AV, Puerto serie, Puerto USB, Puerto Ethernet, audio output interface

1. Entrada AV: Analog audio and video input interface, 6PIN Portador de paso de 1,25 mm, audio support Mic in or Line-in input.
   ml (Mic in light), audio Mic input left channel;
   MR (Mic in right), audio Mic input right channel;
   LL (Line-in light), audio Line in left channel;
   LR (Line in right), audio Line in the right channel;
   Tierra, señal de tierra;
   DE, entrada de vídeo analógico.
2. CFG-UART: equipped with a serial port, 4PIN Portador de paso de 1,25 mm, used for this Encode Board parameter configuration, can be connected to Haida parameter configuration panel or another upper computer. See the above figure for each PIN pin signal.
3. Datos-UART: Puerto serie de datos, 3PIN Portador de paso de 1,25 mm, transmission baud rate and other parameters can be configured through the configuration of the serial port. When this Encode board is connected to another wireless transmission module, the data serial port is used for one-way transparent data transmission. See the figure above for each PIN pin signal.
4. interfaz USB: 4PIN 1.25mm pitch carrier for This Encode Board software upgrade maintenance.
5. Vocero: 2PIN Portador de paso de 1,25 mm, This Encode Board can be connected to the speaker through the Speaker interface. When this Encode Board is connected to the Haida two-way wireless transmission module RCD or other bidirectional links, the input audio is decoded and played, and output to the speaker. PIN foot signal:
   1. SP: Speaker out-P
   2. SN: Speaker out-N
6. Ethernet: interfaz ethernet, 4PIN Portador de paso de 1,25 mm, refer to the above figure for each PIN pin signal. Generalmente, the connector is not soldered when shipped by default.

Solicitud

It can be assembled with another COFDM modulation module RCA, RCB, RC900, etc.. to form COFDM transmitters with different functions, and the connection interfaces are all FPC_Main (26PIN flat cable).

It can also be assembled with another two-way wireless transmission module RCD stack to form a two-way wireless transmission video transmitter, and the connection interface is also the FPC_Main interface.

It can be connected to the parameter configuration panel (ScoA, SconB, SconC, etc.) through the CFG-UART interface to set the operating parameters.

FPV CVBS débil a Ethernet

CVBS a Ethernet IP

HDMI + CVBS a Ethernet IP

IDE + AHD / CVBS a Ethernet IP

Cámara USB UVC a IP Ethernet

Cámara USB UVC a CVBS PAL NTSC

HDMI a Ethernet IP

4HDMI a IP Ethernet

AV analógico a IP Ethernet

Ethernet IP a HDMI CVBS

Ethernet IP a HDMI CVBS

Ethernet IP a HDMI

Ethernet IP a HDMI