এনকোডার মডুলেটর ডিকোডার ডেমোডুলেটর মডিউল প্যারামিটার কনফিগারেশন নির্দেশাবলী COFDM AT কমান্ড
Download the Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions below if you need a PDF file.
Update Record:
সংস্করণ | তারিখ | বিবরণ |
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 | 2016-10-24 2016-11-1 2016-12-26 2017-2-14 2017-2-28 2017-3-27 2017-4-19 2017-5-18 2017-9-12 2018-3-15 2019-6-25 2023-2-24 | Initial version ATDR reply distinguishing module ATSE, ATGE add audio switch Add ATSP protocol Add ATST, ATGT protocol ATGE command add AESfor status acquisition Added ATGB protocol AV and HDMI output control Support for obtaining the current AV output standard Added ATSU, ATGUcommands Added ATOSD, ATSIP, ATGIP commands Added ATSAD, ATGAD commands |
Users may need to modify the configuration parameters of the module during the use of the COFDM modulator and demodulator module. In order to simplify the user’s operation, we design the parameter configuration into a few simple AT commands. The user only needs to use the specified AT command and pass the corresponding parameters to complete the parameter setting of the COFDM module.
Suitable Models
Command Introduction
The AT command for configuring COFDM module parameters starts with “AT” and ends with an underscore “_”. Each AT command has several or no parameters, and each AT command has a return value. For details, please refer to the introduction of the following commands.
Users can configure the parameters of the module through the configuration serial port (TTL এর স্তর, 3.3ভী) of the COFDM module. For detailed serial port configuration, refer to the figure below. Please use tools such as “Serial Port Debugging Assistant” to send AT commands to the COFDM module, pay attention to the use of পাঠ্য, উদাহরণ স্বরূপ:
সিommand Classification
The AT commands for configuring COFDM module parameters are mainly divided into the following two categories:
Query Commands | ATDR, ATGD, ATGE, ATGI , ATGR, ATGT, ATGB, ATGU, ATGIP |
Setting Commands | ATSD, ATSG, এটিএসএম, ATSE, ATSI, ATSO, atsr, ATSP, ATST, ATSU,ATOSD, ATSIP |
From the perspective of whether to save after power-off, the setting commands can be divided into:
Power-off Saving Commands | ATSD, ATSE, ATSI, ATSO, atsr, ATSP, ATST, ATSU, ATSIP |
Power-off Not Saving Commands | ATSG, এটিএসএম, ATOSD |
According to the configuration transmitter or receiver, the classification is as follows:
Sender Configuration Commands | ATDR, ATSD, ATGD, ATSG, এটিএসএম, ATSE, ATGE, ATSI, ATGI, ATSO, ATSP, ATST, ATGT, ATSU, ATGU, ATOSD |
Receiver Configuration Commands | ATDR, atsr, ATGR, ATSP, ATST, ATGT, ATGB, ATSIP, ATGIP |
Command Details
Ping Command
বিন্যাস | ATDR_ |
স্থিতিমাপ | না |
ব্যবহার | for the integrated system to check whether the serial port is connected and identify the connected modules. |
ফেরত মূল্য | RCB returns the “device profile” string SUE1 returns “ATDRSUE1 OK” string SHD1 returns “ATDRSHD1 OK” string |
মন্তব্য | ক্যোয়ারী কমান্ড |
Set Device Command
বিন্যাস | ATSD $(mimo), $(gi), $(কেন্দ্র অপারেটিং ফ্রিকোয়েন্সি পয়েন্ট), $ (নক্ষত্রপুঞ্জ), $(freq(KHz)), $(bw(KHz)), $(tx1_gain), $(tx2_gain)_ উদাহরণ: ATSD0,1,0,0,800000,8000,86.0,86.0_ |
স্থিতিমাপ | One Antenna/Dual antenna mimo: 0 mimo disable; 1 mimo enable Guard Interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1/4 Convolution Code Rate: 0 1/2; 1 2 /3; 2 3/4; 3 5/6; 4 7/8; ঋক্ষ: 0 QPSK; 1 QAM16; 2 QAM64; RCB Carrier Center Frequency(kHz) 200000~2700000(200MHz~2.7GHz, 1KHz ধাপ) RC900 Carrier center Frequency(kHz) 750000~930000(750মেগাহার্টজ ~ 930MHz, 1KHz ধাপ) RCB Channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1KHz ধাপ) RCB Channel bandwidth bw(KHz) 2000~8000 (2MHz~8MHz, 1KHz ধাপ) Transmitting antenna 1 gain tx1_gain 0.0~89.75dB, 0.25dB পদক্ষেপ Transmitting antenna 2 gain tx2_gain 0.0~89.75dB, 0.25dB পদক্ষেপ |
Return Value | যেমন:ATSD0,1,0,0,800000,8000,86.0,86.0_ SISO,সিপাহী: 1/16, সি আর:1/2, MOD: QPSK, freq:800000KHz,bw:8000KHz,tx1_gain:86.000000 tx2_gain:86.000000 ঠিক আছে |
বিঃদ্রঃ | কমান্ড সেট করুন, পাওয়ার বন্ধ হলে সংরক্ষণ করুন. Different Bandwidths, গার্ড অন্তর, Convolution code rates, Data rate calculation formulas corresponding to constellations Air interface rate Rate(কেন্দ্র অপারেটিং ফ্রিকোয়েন্সি পয়েন্ট) কেন্দ্র অপারেটিং ফ্রিকোয়েন্সি পয়েন্ট (ব্যান্ডউইথ(মেগাহার্টজ) * 8.0/7.0) / (1+সিপাহী) * 1512/2048*কেন্দ্র অপারেটিং ফ্রিকোয়েন্সি পয়েন্ট(কেন্দ্র অপারেটিং ফ্রিকোয়েন্সি পয়েন্ট) * কেন্দ্র অপারেটিং ফ্রিকোয়েন্সি পয়েন্ট * 188/204. Taking 8MHz bandwidth as an example, different guard intervals, convolution code rates, data rates corresponding to constellations and required receiving signal-to-noise ratios |
এসet Gain Command
বিন্যাস | ATSG$( tx1_gain),$( tx1_gain)_ উদাহরণ: ATSG85.0,85.0_ |
স্থিতিমাপ | tx1_gain: প্রেরক 1 লাভ করা tx2_gain: প্রেরক 2 লাভ করা |
ব্যবহার | To dynamically adjust the output power. If the signal SNR/RSSI of the receiver is high, the output power can be reduced through the remote control link. When the SNR/RSSI of the end signal is low, increase the output power (প্রেরক) |
Return Value, | উদাহরণ: ATSG85.0,85.0_set gain 85.000000 85.000000 ঠিক আছে |
মন্তব্য | setting command, power off will not save. |
Set Modulation Mode commanঘ
বিন্যাস | ATSM$(gi), $(কেন্দ্র অপারেটিং ফ্রিকোয়েন্সি পয়েন্ট), $(নক্ষত্রপুঞ্জ)_ উদাহরণ: ATSM1,1,2_ |
স্থিতিমাপ | Gard interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1 /4; Convolution code rate: 0 1/2; 1 2/3; 2 3/4; 3 5/6; 4 7/8; ঋক্ষ: 0 QPSK; 1 QAM16; 2 QAM64 |
ব্যবহার | Dynamically adjust the air interface rate, the air interface rate can be increased when the distance is short, and the air interface rate can be reduced when the distance is long (প্রেরক) |
Return Value | উদাহরণ:ATSM1,1,2_GI:1/16, সি আর:2/3, MOD: QAM64, ঠিক আছে |
মন্তব্য | setting command, power off will not save. |
জিet Device Status Command
বিন্যাস | ATGD_ |
স্থিতিমাপ | না |
ব্যবহার | query the current number of transmit antennas, পাহারা ব্যবধান, convolution code rate, number of constellations, transmit frequency, ব্যান্ডউইথ, gain parameters (প্রেরক) |
Return Value | উদাহরণ: ATGD_ SISO, সিপাহী:1 /16, সি আর: 1/2, MOD: QPSK, freq: 800000KHz, bw: 8000KHz, tx1_gain: 86.000000 tx2_gain: 86.000000 ঠিক আছে |
মন্তব্য | ক্যোয়ারী কমান্ড |
Set Encoder Command
বিন্যাস | ATSE$(llc),$(rt),$(bitrate) ,$(gop),$(শ্রুতি)_ উদাহরণ: ATSE0,0,0.0,0,0_ |
স্থিতিমাপ | 1. Enhanced data reliability option llc: 0 disable; 1 enable (requires the receiving end to enable this option at the same time, use in pairs, because more redundant data is added to enhance reliability, the video bit rate of the transmitting end should be set when this option is turned off half of) 2. Real-time priority/quality priority rt: 0 image quality priority; 1 real-time priority; 3. বিট্রেট: 0 let system decide; >0 specify bitrate(float) 4. I frame interval GOP: 0 let system decide; >0 specify GOP 5. Audio encoding option audio: 0 disable; 1 enable |
ব্যবহার | Used to set encoding parameters (প্রেরক) |
Return Value | উদাহরণ:ATSE0, 0,0.0,0,0_ মোড:0,RT:0,bitrate: 0.0এম বি পি এস,gop:0,শ্রুতি:0,ঠিক আছে |
মন্তব্য | setting command, save when power is off. |
Get Encoder Command
বিন্যাস | ATGE_ |
স্থিতিমাপ | না |
ব্যবহার | querying encoding parameters (sending end) |
Return Value | উদাহরণ:ATGE_MODE:0, RT:0,bitrate:4.0এম বি পি এস,gop:10,শ্রুতি:0,aes:0, ঠিক আছে |
মন্তব্য | Query command AES means the current encryption status: 0 disable; 1 enable |
Get Input Command
বিন্যাস | ATGI_ |
স্থিতিমাপ | না |
ব্যবহার | query the current camera input parameters (প্রেরক) |
Return Value | উদাহরণ:ATGI_input_size: 1080পি, input_rate: 60FPS, sensor_type: hdmi,ঠিক আছে |
মন্তব্য | ক্যোয়ারী কমান্ড |
Set Input Command
বিন্যাস | ATSI$(input_size),$(input_rate)_ উদাহরণ: ATSI1080,25_ |
স্থিতিমাপ | 1. Input resolution input_size: 0 let the system detect; >0 specify input size 2. Input frame rate input_rate: 0 let the system detect; > 0 specify input fps |
ব্যবহার | To specify the input resolution and frame rate to meet some special signal sources, or some special application needs (প্রেরক) |
Return Value | উদাহরণ: ATSI1080,25_ Input_size:1080পি,input_rate: 25FPS, ঠিক আছে |
মন্তব্য | After the user specifies the input resolution and frame rate through this command, the system will no longer detect the signal source (use with caution). The user can restore the default through the following command: ATSI0,0_Set the command and save it after power-off. |
Set Output Command
বিন্যাস | ATSO$(output_size),$(output_rate)_ উদাহরণ: ATSO720,30_ |
স্থিতিমাপ | 1. প্রেরক: encoding output resolution output_size: 0 equal to input_size; >0 specify output size 2. গ্রাহক: HDMI output resolution (720, 1080) 3. প্রেরক: encoding output frame rate output_rate: 0 equal to input_rate; >0 specify output_rate (FPS) 4. গ্রাহক: HDMI output frame rate 720p supports frame rate (50, 60); 1080p supports frame rate (24, 25, 30, 50, 60) |
ব্যবহার | 1. প্রেরক: Used to specify the encoding output resolution and frame rate to meet the requirements of certain applications for zooming and frame reduction 2. গ্রাহক: used to configure the resolution and frame rate of HDMI output |
Return Value | উদাহরণ: ATSO720,30_ output_size: 720পি, output_rate: 30FPS, ঠিক আছে |
মন্তব্য | 1. For HDMI input only, this command is invalid for AV input 2. Output_size <= input_size; output_rate<=input_rate 3. Set the command and save it after the power is off. |
Set Input Sources Command (switch HDMI / CVBS ইনপুট)
বিন্যাস | ATSU$(vin),$(ain)_ উদাহরণ: ATSU0,1 _ |
স্থিতিমাপ | 1. Video input selection VIN: 0 let the system detect; 1 force CVBS input; 2 force hdmi/SDI input 2. Audio input selection AIN: 0 let the system detect; 1 force analog input |
ব্যবহার | Used to meet specific application requirements (উদাহরণ: HDMI/SDI input video, MIC input audio) |
Return Value | উদাহরণ: ATSU0,1_ ATSU0,1 OK |
মন্তব্য | setting command, power-off save. |
Get User Command
বিন্যাস | ATGU _ উদাহরণ: ATGU_ |
স্থিতিমাপ | না |
ব্যবহার | To query user-specific configuration |
Return Value | উদাহরণ: ATGU_ ATGU0,1 OK |
মন্তব্য | ক্যোয়ারী কমান্ড return parameter description please refer to the ATSU command |
Set Receiver Command
বিন্যাস | atsr $(freq), $(bw ), $(llc), $(cvbs)_ উদাহরণ: ATSR320000,6000,0,0_ |
স্থিতিমাপ | 1. DR2C carrier frequency freq(KHz) 200000~860000(200মেগাহার্টজ ~ 860MHz, 1KHz ধাপ) 2. DR900 carrier center frequency freq(KHz) 200000~1600000(200MHz~1.6GHz, 1KHz ধাপ) 3. DR2C channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1KHz ধাপ) 4. DR900 channel bandwidth bw(KHz) 3200~8000(3.2MHz~8MHz, 1KHz ধাপ) 5. Enhanced data reliability option llc: 0 disable; 1 enable (it is required that the transmitter should also enable this option at the same time, and use it in pairs. Since more redundant data is added to enhance reliability, the video bit rate of the transmitter should be set to when this option is turned off half of) 6. AV output system cvbs: 0 pal; 1 ntsc |
ব্যবহার | To set the receiver parameter |
Return Value | example: ATSR320000,6000,0,0_ ATSR320000,6000,0,0 OK |
মন্তব্য | setting command, save when power is off. |
Get Receiver Command
বিন্যাস | ATGR_ |
স্থিতিমাপ | না |
ATGR_ | the receiving end parameter |
Return Value | উদাহরণ: ATGR_ ATGR320000,6000,0,aes:0,cvbs:0 ঠিক আছে |
মন্তব্য | 1. Query command 2. Aes parameter indicates the current encryption status: 0 disable;1 enable 3. CVBS parameter Indicates the current AV output standard: 0 pal;1 ntsc |
Get Bit Error Rate Command
বিন্যাস | ATGB_ |
স্থিতিমাপ | না |
ব্যবহার | querying the bit error rate and signal strength of the dual antennas at the receiving end |
Return Value | উদাহরণ: ATGB_ ATGB ber1:0.00% ber2:0.00% RSSI1 :54 RSSI2:53 Lock1:1 Lock2:1 ঠিক আছে |
মন্তব্য | 1. Query commands 2. Ber1 and ber2 respectively indicate the bit error rate of each antenna, ranging from 0.0% থেকে 100.0% 3. RSSI1 and RSSI2 respectively indicate the signal strength of each antenna, ranging from 0 থেকে 100 4. Lock1 and Lock2 respectively indicate the signal locking status of each antenna (1 Represents signal lock) |
Set Password Command
বিন্যাস | ATSP$(পাসওয়ার্ড), $(পাসওয়ার্ড)_ উদাহরণ: ATSP123456, 123456_ |
স্থিতিমাপ | AES কী পাসওয়ার্ড: 6-digit password (ASCII) AES কী পাসওয়ার্ড: 6-digit password (ASCII) (repeat it for confirmation) |
ব্যবহার | ট্রান্সসিভারের AES কী সেট করতে ব্যবহৃত হয় (ট্রান্সমিটার এবং রিসিভার) |
Return Value | উদাহরণ: ATSP123456_ ATSP123456 ঠিক আছে |
মন্তব্য | 1. পাসওয়ার্ড দিলেই সব 0, AES encryption is turned off. 2. Set the command and save it after powering it off. |
Set Data Transfer Command
বিন্যাস | ATST$(বড হার), $( parity)_ উদাহরণ: ATST115200,0_ |
স্থিতিমাপ | 1. Baud rate baud rate: 1200、2400、4800、9600、19200、38400、57600、115200 2. Check Code: 0: কোনোটিই নয়; 1: Odd; 2: Even |
ব্যবহার | Used to set the baud rate and parity bit of the serial port for data transparent transmission |
Return Value | উদাহরণ: ATST115200,0_ ATST115200,0 OK |
মন্তব্য | কমান্ড সেট করুন |
Get Data Transfer Command
বিন্যাস | ATGT_ |
স্থিতিমাপ | না |
ব্যবহার | Used to query the baud rate and check code |
Return Value | উদাহরণ: ATGT_ ATGT115200,0 OK |
মন্তব্য | Query command |
Set IP Address Command
বিন্যাস | ATSIP$(ip), $(ip)_ উদাহরণ: ATSIP192.168.1.215,192.168.1.215_ |
পরামিতি | Local IP address Local IP address (নিশ্চিত করতে পুনরাবৃত্তি করুন) |
ব্যবহার | Used to set the receiver IP address |
Return Value | উদাহরণ: ATSIP_192.168.1 .215,192.168.1.215_ ATSIP192.168.1.215 OK |
মন্তব্য | 1. After setting the IP address, the receiving end needs to be restarted to take effect. 2. Set the command and save it after powering it off. |
Get IP Address Command
বিন্যাস | ATGIP_ উদাহরণ: ATGIP_ |
স্থিতিমাপ | না |
ব্যবহার | রিসিভিং এন্ডের বর্তমান আইপি অ্যাড্রেস জিজ্ঞাসা করতে |
ফেরত মূল্য | উদাহরণ: ATGIP_ ATGIP192.168.0.215 ঠিক আছে |
মন্তব্য | ক্যোয়ারী কমান্ড |
OSD Overlay Protocol
বিন্যাস | ATOSD$(idx), $(এক্স), $(y), $(str)_ উদাহরণ:ATOSD0,40,20,height: 100m_ |
স্থিতিমাপ | 1. IDX index: 0~7 (supports OSD overlay for 8 areas) 2. X-coordinate: 0~1919 3. Y coordinate: 0~1079 4. str: the string to be displayed at the corresponding coordinates (the space symbol is used to clear the display) |
ব্যবহার | on the video screen.OSD information |
ফেরত মূল্য | না |
মন্তব্য | 1. The user specifies the x and y coordinates of the OSD display according to the maximum 1920×1080 পিক্সেল, and the system will correct the coordinates according to the actual display situation. 2. The ‘_’ character cannot be contained in the str parameter |
Set Gain To Adjust
বিন্যাস | ATSAD$(freq),$(adjust) _ উদাহরণ:ATSAD700000,2.5_ |
স্থিতিমাপ | wireless central working frequency: Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) Adjust the value(ডিবি): ATSD cmd will subtract this value to set the wireless gain |
ক্রিয়া | Specify and adjust the value for the wireless gain setting using by ATSD cmd |
প্রতিক্রিয়া | উদাহরণ: ATSAD700000,2.5_ freq:700000,adjust:2.50 ঠিক আছে |
মন্তব্য | Setting command is still valid when stopping power or resetting. |
Get Gain To Adjust
বিন্যাস | ATGAD[$(freq)]_ উদাহরণ:ATGAD700000_ |
স্থিতিমাপ | wireless central working frequency: Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) When no parameter provides, it will list all the freq that have adjusted value. |
ক্রিয়া | Inquiry adjust the value for wireless gain setting using ATSD cmd |
প্রতিক্রিয়া | উদাহরণ: ATGAD700000_ freq:700000,adjust:2.50 OK ATGAD_ freq:700000 750000 ঠিক আছে |
মন্তব্য | Inquiry command. |
Serial Port Utility software download
HTTPS দ্বারা://www.alithon.com/downloads
অনবরত জিজ্ঞাসিত প্রশ্ন
1. How can I return to the No Password setting with 000000 indications after the change?
Reset the password to 000000 (one must not be missing) through the Parameter Configuration Panel Board.
or set it through দ্য ATSP_command
2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (লাভ করা) good for linear output operation? Or do you suggest some limited range for better linear operation?
The Gain of the COFDM configuration is the internal Gain, not the actual output power of the transmitter. The internal gain range is 0~89.75dB and the linear output:
1. At around 300~500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -5dBm.
2. At around 1000~1500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -6dBm to -10dBm.
3. I tried to set – B bandwidth (kHz) and E bit rate (এম বি পি এস). When I set E, the new value does not apply. তাই. the E setting is only for monitoring of available bitrate? if I wish to change the E (বিট্রেট) I have to change only B (ব্যান্ডউইথ)? Am I right?
It is not recommended to modify the video bit rate ‘E’ directly, because if the output video bit rate is greater than the wireless air interface rate, the system will not work normally.
By default, the internal video bit rate ‘E’ will be set to 0 for automatic. Customers only need to modify ‘B’ to modify the wireless parameters, and the video bit rate will automatically adapt.
You can also adjust the wireless air interface rate by modifying GI and CR.
For more details on the Encoder Modulator Decoder Demodulator Module, please send an inquiry to us.
COFDM মডুলেটর Demodulator মডিউল এনকোডার ডিকোডার HDMI CVBS AV ইনপুট AES 256 FHD RF স্ট্রিমিং
পর্যালোচনা
কোন রিভিউ এখনো আছে.