Yagi directional antenna
用於 COFDM 接收器 170-860Mhz 頻率定制 12dBi 的八木定向天線
目錄
規範
頻率範圍
|
170-860兆赫
|
帶寬
|
70兆赫
|
獲得
|
12dBi的
|
極化
|
Vertical or Horizontal
|
Horizontal Half-power Beamwidth
|
54°
|
Vertical Half-power Beamwidth
|
48°
|
Front-to-Back Ratio
|
≧15
|
VSWR
|
≤1.5
|
輸入阻抗
|
50哦
|
最大輸入功率
|
100W¯¯
|
防雷保護
|
DC Ground
|
Input connector type
|
N Female or Customized
|
外形尺寸
|
0.6米
|
天線重量
|
0.8公斤
|
天線罩材質
|
Aluminum Alloy
|
工作溫度
|
-40℃~60℃
|
Rated Wind Velocity
|
60m/s
|
Mounting way
|
Pole-holding
|
安裝硬件
|
¢35mm~¢50mm
|
Here are the product’s real photo
595Mhz Yagi directional antenna for COFDM-912T
類別 Category | 八木定向天线Yagi Antennas |
型號 Model | |
频率范围 Frequency range | 595兆赫 |
带宽Bandwidth | 14 |
增益Gain-dBi | 12 |
水平面波瓣宽度Horizontal Beamwidth | 44 |
垂直面波瓣宽度Vertical Beamwidth | 40 |
前后比 Front-to-Back Ratio | ≥16 |
电压驻波比VSWR | ≦1.5 |
标称阻抗Nominal impedance | 50 |
极化方式Polarization | 垂直或水平Vertical or Horizontal |
最大功率Maximum power-W | 100 |
尺寸Size-cm | 92 |
重量Weight-kg | 0.55 |
抗风强度Rated Iind Velocity-m/s | 60 |
接头型号Connector | 氮鉀 |
支撑杆直径Rod diameter | Ф35-50 |
Installation Notes
1. Fix the antenna director and vibrator reflector on the corresponding position of the main pole.
2. Fix the clamp square tube on the clamp with the provided screws.
3. Align the fixing hole on the other end of the clamping square tube with the clamping fixing hole on the antenna, and fix the antenna with screws.
4. Connect the feeder and wrap the connector of the feeder with waterproof tape.
5. Fix the cable with cable ties, and do not let the falling force of the feeder be applied directly to the antenna connector.
6. Before the cable enters the room from the outside, an anti-backflow section should be formed to prevent rainwater from entering the equipment along the feeder.
安装说明:
1、将天线引向器、振子反射器固定在主杆对应位置。
2、将夹码方管用配备的螺丝固定在夹码上。
3、夹码方管的另一头的固定孔对准天线上的夹码固定孔,用螺丝固定天线。
4、连接好馈线,并将馈线接头用防水胶带包好。
5、用扎带固定好电缆,不要让馈线的下坠力直接施加在天线接头上。
6、电缆从室外进入室内前要形成防倒流段,以免雨水沿馈线进入设备。