COFDM IP wireless data transmitter module
COFDM IP wireless video data transmitter module One-way Ethernet transparent transmission network port Vcan1816

Mục lục
Giới thiệu
- This ethernet COFDM module supports transmitting the data from the ethernet port to TX RF out.
- Common cofdm transmitters are video signal inputs such as HDMI, CVBS, SDI, or AHD. This one is a transparent transmission module that can support IP cameras and support video and data through cofdm.
- Paired with this COFDM network video data transmitter is a COFDM receiving module, which can realize HDMI and CVBS output, and can also output video to a computer, RTSP, or UDP player through an IP network port RJ45.
- The key role is to use UDP broadcast/multicast to send data.
-
COFDM modulation with low latency;
-
Stable signal transfer in NLOS and high-speed moving;
-
Adjustable working frequency 170-4000Mhz, băng thông, công suất truyền tải, vân vân;
-
Ethernet connection for IP data UDP broadcast transmission
-
Maximum 31.67Mbps wireless transmitting bitrates
-
Embedded RTSP video client to get video from IP camera via Ethernet connection

- COFDM wireless transmission module + receive the module, forming a one-way wireless transmission network port transmission link
- The transmitting module receives data through the network port and transmits the data received by the network port in the form of COFDM
- After receiving the data, the receiver receives the demodulation and then outputs it through the network port

Unidirectional COFDM network port wireless transmission module function:
Tính năng, đặc điểm
- The host computer data is received through the network port, and then the network port data is transmitted.
- Nhập dữ liệu: Network port, support protocol UDP broadcast/multicast. Physical interface: RJ45 seat or 4PIN 1.25mm pitch seat
- CFG-UART: COFDM modulation parameter configuration serial port, 4PIN 1.25mm pitch seat, can be docked to our parameter configuration panel. Users can set the center operating frequency point, băng thông không dây, and other modulation parameters (such as protection interval, convolution bitrate, chế độ chòm sao, transmission gain, vân vân.) through the reference serial port.
- COFDM Transmitter Interface (Tx): MMCX nữ.
- Giao diện thẻ TF, nâng cấp phần mềm, and maintenance.
- Giao diện đầu vào nguồn (Quyền lực): 2PIN 2.0mm pitch Phoenix terminal. điện áp cung cấp: 7V~24V.
- Link LED indicator: The light of the work is emitted, and the data is flashed when the data is transmitted usually.
- Power LED indicator: The power input indicator, the normal power supply is always on.
- Transmitter module size: 73x51mm (excluding the size of interface devices and connectors protruding from the board edge), thickness less than 15mm.
- Supported COFDM modulation parameters:
- Configurable convolutional encoding ratios: 1/2, 2/3, 3/4, 5/6, 7/8
- Configurable constellation: QPSK/QAM16/QAM64
- IFFT mode: 2K
- Configurable protection intervals: 1/4, 1/8, 1/16, 1/32
- Băng thông không dây: 1 ~ 8MHz MHz adjustable, 1Bước KHz
- Configurable RF output power: -94dbm ~ -5dbm (different operating frequency points, the maximum transmit power is different).
- Center operating frequency point: between 200MHz ~ and 2300MHz can be configured arbitrarily

Đặc điểm kỹ thuật
IO
| đầu ra RF | MMCX nữ |
| TTL 3.3V control uart | 4Đầu nối PIN PH1.25mm |
| Cấp nguồn vào | 2Đầu nối phenix PIN PH2.54mm |
| cổng Ethernet | 4Đầu nối PIN PH1.25mm |
| thẻ TF | Để cập nhật chương trình cơ sở |
| Đèn led nguồn | Red constant light when the device is normally powered |
| Liên kết dẫn | Green blinks on transmitting |
điều chế
| Định dạng điều chế | COFDM(DVB-T) |
| Hãng vận chuyển | 2K |
| Băng thông | Có thể định cấu hình từ 1 MHz đến 8 MHz, từng bước 1KHz |
| FEC | 1/2, 2/3, 3/4, 5/6, 7/8 |
| khoảng bảo vệ | 1/32, 1/16, 1/8, 1/4 |
| chòm sao | QPSK, 16QAM, 64QAM |
Truyền RF
| Dải tần số | 70MHz~4GHz |
| Kích thước bước điều chỉnh | 1KHz |
| Công suất truyền tải | Có thể cấu hình, tối đa -5dBm(tùy thuộc vào tần số) |
Giám sát và kiểm soát
Thiết lập toàn diện với Bảng cấu hình của chúng tôi hoặc thiết bị khác thông qua uart điều khiển.
Phạm vi nhiệt độ
Thông số kỹ thuật đầy đủ: -40° đến +70°C Môi trường xung quanh
Kho: –40° đến +85°C
Kích thước
73x51x11mm (không bao gồm các đầu nối ra khỏi bảng)
Yêu cầu về nguồn điện
Phạm vi đầu vào: 7~24VDC
Tiêu thụ điện năng: <250mA@12V
I/O Signal

RJ45 ethernet COFDM Transmitter for the IP camera video Transmission

This ethernet IP input COFDM Video transmitter module can receive video from an IP camera via an Ethernet connection with a built-in RTSP client and transmit it. On the COFDM receiving side, our COFDM module has a built-in RTSP Server that allows video streaming over Ethernet for remote software or hardware decoders.
How to use it as the COFDM Relay repeater module?
This module already has a TX transmission function. If you add a dual-antenna receiving module and combine them, you can form a COFDM relay/repeater module. Tất nhiên rồi, you need to add a bandpass filter to filter out clutter interference and increase PA to transmit a longer range. If you need customization, vui lòng liên hệ với chúng tôi.

Giải điều chế và điều chế
| Định dạng điều chế | COFDM(DVB-T) |
| Hãng vận chuyển | 2K |
| Băng thông | Có thể định cấu hình từ 1 MHz đến 8 MHz, từng bước 1KHz |
| FEC | 1/2, 2/3, 3/4, 5/6, 7/8 |
| khoảng bảo vệ | 1/32, 1/16, 1/8, 1/4 |
| chòm sao | QPSK, 16QAM, 64QAM |

Đã nhận được RF
| Dải tần số | 160MHz~860 MHz |
| Kích thước bước điều chỉnh | 1KHz |
| Nhạy cảm | -97±1dBm(BW=8 MHz, QPSK, CR=2/3, GI=1/16) for one channel and add 3dBm for two-channel |
Truyền RF
| Dải tần số | 70MHz~4GHz |
| Kích thước bước điều chỉnh | 1KHz |
| Công suất truyền tải | Có thể cấu hình, tối đa -5dBm(tùy thuộc vào tần số) |
COFDM wireless transmission system transmission rate calculation
Wireless transmission rate (tốc độ giao diện không khí):
Tỷ lệ(MBps) = (BandWidth(MHz) * 8.0/7.0) / (1+GI) * 1512/2048*log2(constellation point) * code_rate * 188/204.
Take the 8MHz bandwidth as an example of different protection intervals, convolutional bitrates, data rates corresponding to constellations, and the required received signal-to-noise ratio:

UART AT Command
ATDR、ATSD、ATSG、ATSM、ATGD、ATSR、ATGR、ATGB is useful
For the UART AT command operation and format, vui lòng kiểm tra liên kết bên dưới.
Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions COFDM AT Command
Receiver Module

Suggestions
- This is a one-way unidirectional transmission system. if you need a two-way bidirectional transmission system, vui lòng kiểm tra liên kết này. https://ivcan.com/t/two-ways/ or https://ivcan.com/ru/p/mini-cofdm-wireless-ethernet-transmission-module-rj45/
- This is only a data transmission system, if you need video+data transmission, please look details of these modules, https://ivcan.com/p/modulator-demodulator-module-encoding-decoding-hdmi-cvbs/
- If you need a relay (bộ lặp) to support a longer transmission range (distances), please choose stronger PA (Bộ khuếch đại công suất) bên trong, Ví dụ, change 1Watts PA to 2.5 Watt hoặc 5 Watt.
–160MHz~860MHz HD video COFDM receiver module with HDMI/AV/Ethernet/USB output

The COFDM receiver module is a compact digital diversity receiver with integrated H.264 decoding, thích hợp để sử dụng trong các ứng dụng chất lỏng và tính di động cao. The receiver module accepts signals from two antennas to significantly enhance the demodulated performance and increase the operating range. The receiver module can find and lock automatically to the incoming transmission quickly according to the pre-set frequency and bandwidth. This receiver module features a range of comprehensive signal outputs including HD at 720p and 1080P, video màn hình HD CVBS được chuyển đổi xuống, và hai âm thanh analog được hỗ trợ.
The receiver module also includes DVR record functionality with a Micro SD card or USB disk. Ngoài ra, the receiver module has a built-in RTSP server that enables video streaming over Ethernet for remote software or hardware decoders. And the receiver module also enables video streaming over USB for remote Android device decoders like smartphones or Android PAD. This allows multiple remote viewers to monitor the same video simultaneously. The receiver module also supports display characters string on the video display screen with the video together in OSD mode.
When paired with the Our COFDM transmitter module, the receiver module offers a comprehensive, giải pháp âm thanh và video có thể triển khai nhanh chóng cho phép nhận thức tình huống nâng cao. Nó có thể đóng một vai trò thiết yếu trong việc cung cấp video trực tiếp theo thời gian thực từ cả nền tảng di động trên mặt đất và trên không..
- COFDM demodulation and H.264 video decoder;
- Độ phân giải Full HD, 1080P@60fps;
- Bảo mật tuyệt vời bằng giải mã AES;
- DVR record with Micro SD card or USB disk;
- Built-in RTSP server enables video streaming over Ethernet;
- Enables video streaming over a USB host for the remote device;
- Supports display characters string on the video display screen in OSD mode;
- Stable signal transfer in NLOS and high-speed moving;
- Tần số làm việc có thể điều chỉnh, và băng thông.
Đặc điểm kỹ thuật:
IO
| Đầu ra video HD | Đầu nối HDMI loại A |
| Đầu ra video tổng hợp | 6Đầu nối PIN PH2.0mm |
| Đầu ra âm thanh | Embedded HDMI and CVBS |
| đầu vào RF | Two SMA female 50Ω |
| Cấp nguồn vào | 2Đầu nối PIN PH2.54mm |
| Máy chủ USB | 4Đầu nối PIN PH2.0mm |
| Dữ liệu TTL UART | 3Đầu nối PIN PH1.25mm, 3.3V signal |
| Điều khiển UART TTL | 4Đầu nối PIN PH1.25mm, 3.3V signal |
| Ethernet | 6Đầu nối PIN PH2.0mm |
| Thẻ TF | Khe cắm thẻ TF |
| Phím&đèn LED | 2*5Đầu nối PIN PH2.0mm |
giải điều chế
| Định dạng giải điều chế | COFDM(DVB-T) |
| Hãng vận chuyển | 2K |
| Băng thông | Có thể định cấu hình từ 1 MHz đến 8 MHz, từng bước 1KHz |
| FEC | 1/2, 2/3, 3/4, 5/6, 7/8 |
| khoảng bảo vệ | 1/32, 1/16, 1/8, 1/4 |
| chòm sao | QPSK, 16QAM, 64QAM |
| Tốc độ bit | 0.5Mb/giây đến 31,67Mb/giây |
RF
| Dải tần số | 160MHz~860 MHz |
| Kích thước bước điều chỉnh | 1KHz |
| Nhạy cảm | -97±1dBm(BW=8 MHz, QPSK, CR=2/3, GI=1/16) cho một kênh và thêm 3dBm cho hai kênh |
Video và âm thanh
| Đầu ra video | HDMI và CVBS, Ethernet(Giao thức RTSP theo mặc định, tùy chọn UDP), USB |
| Định dạng video | 1080P hoặc 720P
720*480 60TÔI(NTSC), 720*576 50TÔI(PAL) |
| Giải Mã Video | MPEG-4/H.264 AVC |
| Đầu ra âm thanh | Âm thanh HDMI và AV nhúng |
| Giải mã âm thanh | AAC |
| giải mã | AES256 |
| Kho | Đĩa USB hoặc thẻ micro SD |
Giám sát và kiểm soát
Comprehensive receiver setup with Our Config Panel or Windows PC or other devices via control UART.
Phạm vi nhiệt độ
Thông số kỹ thuật đầy đủ: 0° đến +70°C Môi trường xung quanh
Kho: –40° đến +80°C
Đặc điểm vật lý
Board Dimensions: 80.4*50.8mm
Yêu cầu về nguồn điện
Phạm vi đầu vào: 9~24VDC
Tiêu thụ điện năng: <300mA@12V
IO Signals


Phím + đèn LED:
The receiver module has a 2*5PIN PH2.0mm connector which provides “keys + LEDs” signals. It is designed for customers who want to expand LEDs and keys to their cases.
PWR led signal: this two-pin can connect to an led for the power indicator, and constant light when the device is normally powered.
The link led signal: this two-pin can connect to an led for a wireless link indicator, which blinks when the video stream is received.
REC led signal: this two-pin can connect to an led for a record indicator, and constant light when video recording.
REC key signal: this two-pin can connect to a button for the switch of video recording, and a short press to change its status. The receiver will automatically check the storage device(thẻ micro SD hoặc đĩa USB) after powering on and start to record video when the storage device is inserted. Just press it to stop or record again.
Phím OSD: this two-pin can connect to a button for turning on/off the status of the OSD displaying, nhấn và giữ nó để chuyển đổi(hơn 1 giây). The status will be kept after a reboot. Khi trạng thái OSD bật mà không có bất kỳ đầu vào dữ liệu OSD nào từ uart dữ liệu, thiết bị sẽ hiển thị thông tin trên màn hình video dưới dạng:
RF:338.0MHz BW:4.0MHz ; RF, tần số làm việc; BW, băng thông
QPSK CR:2/3 GI:1/16 ; chòm sao, FEC, khoảng bảo vệ
KHÔNG KHÍ:3.90Mb/giây ; KHÔNG KHÍ, tốc độ bit truyền không dây
VBR:3.05Mbps AES OFF ; VBR, tốc độ bit video; TẮT AES, Mã hóa AES đã tắt.
SIG1:27 SIG2:22 ; SIG1, the signal intensity of antenna 1; SIG2, the signal intensity of antenna 2
ber1:0.14% ber2:100.00% ; ber1, bit error rate of antenna 1; ber2, bit error rate of antenna 2
REC OFF Không lưu trữ ; video recording status

Paired with COFDM transmitter:
The default normal features of the two-antenna Wireless receiver module can be paired with all of Our H.264 transmitter modules. The HD video latency from its inputting of the transmitter to the HDMI screen displaying of the receiver is about 200~250ms.
Our two-antenna COFDM Wireless Receiver module can also be paired with our COFDM transmitter module for the lowest video latency application when manufactured with specified firmware. The specified firmware enables proprietary H.264 video compression/decompression only using p-frames for the lowest latency. Độ trễ video từ lúc đưa bộ phát đến màn hình HDMI hiển thị của bộ thu là khoảng 50ms đến 130ms.


How to test COFDM IP wireless video data transmitter module?
ethernet modem in one way
Câu hỏi thường gặp
Please note that this network transparent transmission device is one-way transmission, it can only realize UDP broadcast function, although there is an RJ45 network port, but because it is not two-way transmission, it cannot realize the ping command, so even if you want to connect an IP camera, you need special customization IP cameras, because ordinary IP cameras need two-way transmission equipment.
How to test this network transparent transmission device, vui lòng kiểm tra liên kết bên dưới
How to test COFDM IP wireless video data transmitter module
KHÔNG, just net transfer via IP ethernet RJ45 input.
- If you want to test the video transfer, maybe you need an encoder board Vcan1746, transfer HDMI / CVBS video to IP stream, then connect the 1816 máy phát.
- Câu hỏi: I already have Vcan1776, which has a Vcan1746 encoder board at the transmitter module, should I get one more encoder board?
- Trả lời: Although the encoder board of Vcan1776 can be reused. It needs to disassemble the Vcan1776 RF module, then connect the network port adapter cable, and change the different firmware. It is not recommended to do this. It is recommended that you purchase another separate encoder board.
- The voltage range of TX RX is 7~24V.
- At 12V power supply, use an adapter with a maximum of 1A or more.
- Prepare a formattedFAT32format Micro SD card

fat32-format - Unzip the upgrade file from our verify and send to you, Here is "1816_update_image_xx_yy.zip" tài liệu, and copy it to the root directory of the Micro SD card, pay attention to keep the directory structure unchanged (there is a flash folder in the root directory of the Micro SD card, and there is an app folder in it).

one-way ethernet transparent transmission moudle firmware upgrade - Insert the Micro SD card into the Vcan1816 module, power on and wait for the red light on the board to flash, indicating that the upgrade is successful.

COFDM IP wireless video data transmitter module One-way Ethernet transparent transmission network port upgrade firmware - Ghi chú:
Under normal circumstances, the update will be completed within 30s after power-on (the red light flashes). If the red light does not flash for a long time after power-on, please check the connection of Micro SD and try power-on again.
Vâng, this model support the function you need. Vui lòng kiểm tra hình ảnh bên dưới, we have two solutions for you. The same TX module, there are optional RX1 or RX2 for you.

- At the above picture, TX module is only RJ45 ethernet data input, no video input, so there is no any encoder function.
- RX1 is added 2x RF demodulator board on the TX module. So the cost is higher than TX module. (one more top board)
- RX2 has same function, but which no TX transmitting function, it is only bottom decoder board + 2xRF demodulator board. It has RJ45 ethernet data port. So it can total meet your demand. And as the board has mass produce and cost can share and down.









Konstantin –
The COFDM IP wireless video transmitter vcan1816 delivers exceptional performance! Its one-way Ethernet transparency ensures seamless HD video/data transmission with ultra-low latency. Robust signal stability in challenging environments impressed us, while the plug-and-play network port simplified integration. Reliable beyond expectations for industrial/outdoor applications – a game-changer for real-time remote monitoring systems!
John –
This COFDM module provides reliable IP video and data transmission over distances of 10 ĐẾN 100 km, with latency under 50 mili giây. Customizable core modules are ideal for oil rigs, disaster relief drones, and battlefield communications.