2 وات 5 وات 10 Watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter TDD
$450.00 – $980.00
2 واٽس يا 5 واٽس يا 10 watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter TDD
هي هڪ وائرليس وڊيو ٽرانسميٽر جو هڪ اهم حصو آهي, جيڪو آر ايف سگنل کي ڊگھي رينج ۽ فاصلي لاءِ وڌائي سگھي ٿو. اختياري 1 واٽ, 2 واٽ, 5 واٽ, ۽ 10 واٽ.
مواد جو جدول
خاصيتون
- فريکوئنسي بينڊ: 800Mhz-830Mhz, 1425MHz-1455MH
- آر ايف ۾: 25± 2dBm
- آر ايف جي طاقت: 2 واٽ (33dBm)
- 1400Mhz Transmitter gains 11dB when used with هڪ ٻه طرفي وائرليس وڊيو ڊيٽا لنڪ ماڊل, وڌ ۾ وڌ آر ايف پاور کي 22 ~ 24 dBm طور سيٽ ڪريو, then the RF out power will be 33~35 dBm.
- 800Mhz ٽرانسميٽر حاصل: 13ڊيٽابيس, when used with a two-way wireless video data link module, وڌ ۾ وڌ آر ايف پاور کي 20 ~ 22 ڊي بي ايم جي طور تي سيٽ ڪريو, then the RF out power will be 33~35 dBm.
- آر ايف جي طاقت: 5 واٽ (37dBm)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, set up the maximum RF power as 22~25 dBm, then the RF out power will be 37~37 dBm.
- 800Mhz ٽرانسميٽر حاصل: 17ڊيٽابيس, when used with a two-way wireless video data link module, وڌ ۾ وڌ آر ايف پاور کي 20 ~ 22 ڊي بي ايم جي طور تي سيٽ ڪريو, then the RF out power will be 37~39 dBm.
- آر ايف جي طاقت: 10 واٽ (40dBm)
- موڪليو 'حاصل: 18ڊيٽابيس, when used with a two-way wireless video data link module, set up the maximum RF power of as 22~24 dBm, then the RF out power will be 40~42dbm.
- 2 Watts Power in DC12V~16V;
- 5 Watts Power in DC24V~25V, minimum 1.8A@24V power current rating
- 10 Watts Power in DC24V~30V, minimum 2.5A@28V power current rating
- 2 Watts Power consumption: <6اوله سراسري; 5 Watts Power consumption: <14اوله سراسري; 10 Watts Power consumption: <28W اوسط
- 2 وات 5 Watts PCBA size: 46.5*31ميلي, PCB جي ٿولهه: 1.2ميلي
- 10 Watts Dimensions: 65*62*13.5ميلي, not including the connector out of the metal housing, وزن: 98ز
- Impedance: 50 ohm
سان گڏ ڪم ڪندي هڪ ٻه طرفي وائرليس وڊيو ڊيٽا لنڪ ماڊل:
عمير داخل ٿيل
آر ايف آئوٽ
| وائرليس ويڊيو ٽرانسميٽر SDI ڪئميرا لاءِ ڊگھي رينج COFDM ڊائون لنڪ ٽرانسميٽر | We should solder two bonding pads to connect with power VDD and GND. |
| ڪنٽرول | We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL ۽ GND). ان پٽ اعلي (1.8V کان 3.3V) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode. |
| آر ايف ۾ | ٻه طرفي وائرليس وڊيو ڊيٽا لنڪ ماڊل جي مکيه اينٽينا سان ڪنيڪشن لاءِ IPEX کنیکٹر. |
| آر ايف ٻاهر | We should solder the bonding pad to an antenna connector. |
هائوسنگ ڪيس ۽ گڏ ڪرڻ
We recommend that this power amplifier for our two-way wireless video data link OEM PCBA module.
To enhance the power amplifier in conjunction with our two-way wireless video data link module, we recommend you fabricate a metallic housing casing that aligns with your device’s architecture.
It should also leave at least 6mm between the PA board and the upper cover. In order to facilitate heat dissipation and establish an electrical grounding connection, the back side of the PA board must be directly and firmly attached to the metal.
Proper integration of heat dissipation techniques, such as a heat sink or fan, is essential for optimal performance in designs utilizing the PA OEM module.
We can also make a metal chamber for this PA module according to the customer’s requirement.
The below model has a built-in Power Amplifier inside.
لوڊ:
ق: Could you tell me your RF power amplifier dimension size? I want to design my enclosure.
هڪ: مهرباني ڪري هيٺ ڏنل تصوير چيڪ ڪريو. And tell us if you need any further information.
ق: ڇا توھان مون کي پنھنجي آر ايف لڪير پاور ايمپليفائر جون حقيقي تصويرون ڏيکاري سگھو ٿا?
هڪ: يقين, مهرباني ڪري هيٺ ڏنل تصويرون چيڪ ڪريو.
ق: Are you not using the TQP7M9104 amplifier in the 2W module?
هڪ: نه
