HD پورٽبل COFDM موبائل وڊيو وائرليس ٽرانسميشن سسٽم استعمال ڪندڙ دستياب

COFDM Mobile Video Wireless Transmission users manual for COFDM-908T and COFDM-912T

Users Manual for COFDM Mobile Video Wireless Transmission

This is a manual for COFDM-912T and COFDM-908T. If the HD input is mentioned in the text, it refers to the COFDM-908T model. If the SD input is mentioned in the text, it refers to the COFDM-912T model. Please Pay attention to the distinction.

1. خاصيتون

• انتهائي مربوط, الڳ جوڙجڪ
• COFDM ماڊل ٽيڪنالاجي کي اپنائڻ, H.264 تصويري ڪوڊنگ ٽيڪنالاجي
• Can transmit one 1080P HDMI signal and one unidirectional data up to 230400Kbps
• گھٽ latency, the minimum end-to-end latency is 350ms
• سڀ-گول رابطي, ڀتين جي تعمير کان ڊڄو نه
• High-speed travel-to-travel communication,
• ٽرانسميٽر گرمي ڪڻڪ جي قسم ايلومينيم ڪيس, shockproof and impact resistant
• غير ليڪ-جي-اکيون (NLOS) موبائل ٽرانسميشن, the transmission distance of 2W power is not less than 30 kilometers under the condition of no interference, the transmission distance of 5W power is not less than 50 ڪلوميٽر, and the transmission distance of 10W power is not less than 80 ڪلوميٽر
• وڌ کان وڌ رفتار واري رفتار 600 ڪلو ميٽر / ڪلاڪ تائين پهچي سگھي ٿي (ماپي)
• آڊيو ۽ وڊيو سگنلز جي هم وقت سازي جي استقبال, اختياري اختياري HDMI1080P, معياري-معياري پيداوار ڊي وي ڊي تصويري معيار
• وصول ڪندڙ ويڊيو رڪارڊنگ ۽ بيڪ اپ افعال جو احساس ڪري سگهي ٿو
• 128-bit اي اي ايس انڪريپشن ۽ ڊڪشنريشن
• Can provide full customization

2. درخواست

This product is mainly used in technical reconnaissance and evidence collection of public security and safety inspection departments, real-time picture transmission of drones and unmanned ships, radio and television broadcasting, broadcasting live broadcasting: براڊڪاسٽنگ جي ميدان ۾, راندين جي نشريات, سماجي خبر、وايو رهن ٿا、هڪڙو, mountaineering expeditions and more. هي شهري علائقن وانگر مختلف پيچيده ماحول ۾ اعليٰ معيار واري تصويرن جي حقيقي وقت لاءِ موبائل ٽرانسميشن لاءِ مناسب آهي, سمنڊ, ۽ جبل.

3: Parameter Indicators

1: Transmitter (only standardized pictures, except for customization)

Product parameters:

2: رسيور

Product parameters:

4: Instructions for use

1: Transmitter

1. Functional area description

“جيترو”: Transmitting antenna interface, please connect the antenna before powering on

“HDMI”: High-definition video input interface, input below 1080/50P

“Ctrl”: Transmitter tuner connection interface

“ڊپٽي ڪمشنر 12V”: DC12V power input port. “+” is the positive pole of the power supply, “-” is the negative pole of the power supply

“ڊپٽي ڪمشنر” آهي: Power indicator light, when the light is always on, it means that the power input of the transmitting module is normal

“TS”: Video input detection indicator light, this light is always on to indicate video input and normal encoding

2. Parameter Configuration Description

Connect the transmitter parameter adjuster, press the “MENU/OK” key to enter the menu, the encryption key and data serial port parameters are displayed first, press the left or right key to move the cursor, and the up and down keys to adjust the parameters

After the parameter setting is completed, پريس “MENU/OK” to enter the next menu, and the interface is displayed as shown in the figure

Press the left or right key to move the cursor, press the up or down key to adjust the required parameters, the interface prompts as shown in the figure

After all parameter settings are completed, press the “MENU/OK” key to confirm, and the display will be as shown in the figure.

After the setting is completed, the parameters are written successfully, and the display is as shown in the figure

3. General Troubleshooting

هڪ: The light is off after the power is turned on: Check whether the power input meets the standard

ب: “TS” indicator light is off: Check the video input connection cable, check whether the video input format conforms, and check whether the camera is interfered with (you can judge by holding the antenna with your hand).

سي: The temperature of the transmitter is very low: check whether the current is normal (the deviation can be ±0.2A within the standard current).

ڊي: Three lights are always on, and one of them is super bright: it means that the transmitter has failed the detection, and you can try to power off and restart (uncommon)

2: رسيور

1. Functional area description

“RF in1” “RF in2”: receiving antenna interface, it is recommended to connect the antenna and then turn on the power switch, because the static electricity of the human body may cause the receiver to crash.

“HDMI”: وڊيو آئوٽ انٽرفيس, the output video format can be adjusted through the “HDMI” menu on the control panel.

“ڊپٽي ڪمشنر 12V”: بجلي پٽ انٽرفيس, please strictly follow the power supply voltage requirements, and overvoltage input is strictly prohibited

“چالو بند”: power switch.

“نيٽ ورڪ”: video storage interface, when the U disk is inserted, press the “EXIT” button to start the video recording, after the recording is successful, the video display will display the video recording time, and the stored file name is “TS”.

2. LCD parameter description

هڪ：CH01 UNLOCKED（LCKED）

“CH01” means the channel number of the receiver, “UNLOCKED” means the received signal is unlocked, ۽ “LCKED” means the signal is locked. “CH00” of the receiver is the initial writing channel, and the default channel corresponding to the normal operation of the transmitter is “CH001”

ب： FREQ：602.0MHz

“602.0MHz” is the receiving frequency of the receiver, this frequency must be consistent with the frequency set by the transmitter, otherwise the receiver will not search or receive the signal from the transmitter

ج： ابن:6.0MHz

“ابن” رفتار, as shown in the figure, “ابن: MHz” is understood as the RF bandwidth is 6MHz, this bandwidth must be consistent with the bandwidth set by the transmitter, otherwise the receiver will search for or cannot receive the signal from the transmitter

ڊي： رٿا:1/2

“رٿا: 1/2” is the channel error correction, this parameter synchronizes the parameters set by the transmitter, and the receiver cannot be modified

e： GI:1/32

“GI:1/32” is the channel guard interval, this parameter is set by the transmitter synchronously, and the receiver cannot be modified

f:MAP: QPSK

“MAP: QPSK” is the modulation mapping, this parameter number is set by the transmitter synchronously, and the receiver cannot be modified

ز： SNR:0.0ڊيٽابيس(SNR:15.0ڊيٽابيس)

“SNR: 15.0ڊيٽابيس” is the signal quality (that is, the signal-to-noise ratio, the larger the value, the better). جڏهن “0.0ڊيٽابيس” is displayed, the signal quality is 0, and the receiver will not be able to lock

“(SNR:15.0ڊيٽابيس)” means the receiving signal-to-noise ratio is greater than 15dB. In the “QPSK” modulation mapping state, as long as the signal-to-noise ratio is greater than 6dB, the receiver can lock

ايڇ: PW：-72.1dBm（PW:-72.1)

 PW is the received signal strength, (reference level value), the farther the transceiver end is relative to the distance, the weaker the signal strength is, and the larger the displayed value is, when the transmitter is not turned on, if the signal strength of the receiver is greater than -90dBm (such as -79.7dBm), it can be considered as adjacent frequency interference

3. Parameter Configuration Description

Power on the receiver, and press the “MENU/OK” button to enter the menu, the first display is the menu of adjustable parameters, if you search for a specified frequency, directly press the “MENU/OK” button to enter the menu; if you want to remove the channel, press Press down to select “ListanbulChannel”, and then press “MENU/OK” to enter the menu operation; if you need to change the video output format, move the cursor to the “HDMI Mode” menu, پريس “MENU/OK” to enter, and select the video to be output After formatting, press the “MENU/OK” key to confirm.

The frequency search method is as follows. After entering the frequency setting menu, the interface is displayed as shown in the figure. Press the left or right key to move the cursor, press the up or down key to adjust the frequency, عمير رفتار, and secret key that match the transmitter, and press the “MENU /OK” key to search. Note that the transmitter must be turned on at this time, ٻي صورت ۾, the receiver will not be able to lock because it cannot find the signal.

COFDM Mobile Video Wireless Transmission with a cheap price is including a transmitter and receiver for China directly

When the search is completed, پريس “MENU/OK” پڪ ڪرڻ, and the channel is saved in the register of the assistant board, as shown in the figure. To save the channel to the receiver register, press the “MENU/OK” key and the right key at the same time.

After the receiver parameter setting is completed, the functions of the panel keys are as follows

“↑”“↓“: each individually selectable receiver channel “CH**”

“←”“→“: You can choose to view the hidden parameters of the receiver

“EXIT”: start and stop recording

4. Video function

 Insert the storage device into the “نيٽ ورڪ” interface of the receiver, press the “EXIT” button to start recording, and a blue recording time box will appear on the upper left corner of the video display as shown below

5. General Troubleshooting

هڪ: The value after the receiver displays “-” is very low (Tx is not turned on): It means that the current channel has serious electromagnetic interference, and the normal value is -90- -100.

ب: Cannot record video: check the U disk or replace the U disk.

سي: No signal received: Check whether the channel frequency is consistent with the transmitter.

ڊي: No video output: Check the connection line, power off, and restart to check whether there is a boot interface.