COFDM Mobile Video Wireless Transmission users manual for COFDM-908T and COFDM-912T
Users Manual for COFDM Mobile Video Wireless Transmission
This is a manual for COFDM-912T and COFDM-908T. If the HD input is mentioned in the text, it refers to the COFDM-908T model. If the SD input is mentioned in the text, it refers to the COFDM-912T model. Please Pay attention to the distinction.
Cuprins
1. Caracteristici
- Foarte integrat, design modular
- Adoptă tehnologia de modulare COFDM, Tehnologie de codare a imaginii H.264
- Can transmit one 1080P HDMI signal and one unidirectional data up to 230400Kbps
- Latenta scazuta, the minimum end-to-end latency is 350ms
- Toate-rotund de comunicare, nu se tem de a construi ziduri
- High-speed travel-to-travel communication,
- Transmițător carcasă tip aluminiu tip radiator, rezistent la socuri si la impact
- Non-line de vizare (NLOS) transmisie mobilă, the transmission distance of 2W power is not less than 30 kilometers under the condition of no interference, the transmission distance of 5W power is not less than 50 kilometri, and the transmission distance of 10W power is not less than 80 kilometri
- Viteza maximă de mișcare poate ajunge la 600 km / oră (măsurat)
- Recepția sincronă a semnalelor audio și video, opțiune multi-format HDMI1080P de înaltă definiție, ieșire cu definiție standard calitate DVD a imaginii
- Receptorul poate realiza funcții de înregistrare video și backup
- 128-criptare și decriptare bit AES
- Can provide full customization
2. cerere
This product is mainly used in technical reconnaissance and evidence collection of public security and safety inspection departments, real-time picture transmission of drones and unmanned ships, radio and television broadcasting, broadcasting live broadcasting: câmp de radiodifuziune, radiodifuziune sportivă, știri sociale、aeriene în direct、studio, mountaineering expeditions and more. Este potrivit pentru transmisia mobilă în timp real a imaginilor de înaltă calitate în diverse medii complexe, cum ar fi zonele urbane, mări, și munți.
3: Parameter Indicators
1: Transmiţător (only standardized pictures, except for customization)
Product parameters:
Modulare | COFDM |
tensiune de operare | DC11V~DC17V |
curent de lucru | 1W:≤1.3A DC12V,5W:≤2.5A DC12V,10W:≤5.2A DC12V, |
interfață de control | Standard RS232 interface, 8 biți de date, 1 bit stop, chiar paritate, rata de transfer: 19200 |
interfață de date transparentă | Transmisie port-serie serială unidirecțională, 8 biți de date, 1 bit stop, sprijini paritate impar, chiar paritate, paritate wireless, rata de transfer: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 、230400 |
Criptarea | Suportă criptarea pe 128 de biți |
maparea modulației | QPSK(4QAM)、16QAM、64QAM |
corectarea erorilor înainte | 1/2 2/3 3/4 5/6 7/8 |
interval de protecție | 1/32 1/16 1/8 1/4 |
Numărul de transportatori | 2k |
lățimea de bandă de frecvență | 2/3/4/5/6/7/8M reglabil |
flux de transport | 2000kbs ~ 20000kbs reglabil |
transmite putere | 1W/5W/10W |
frecvența transmisiei | Any frequency can be customized, the frequency is continuously adjustable, the adjustable range is ±20MHz, and the step is 1MHz |
planeitate Putere | Less than 0.2dB in 10MHz band |
raportul umăr | The shoulder-to-shoulder ratio is better than -28dB at full power output |
second harmonic | ≤-45dB |
MORE | 32dB |
video de intrare | 720×480 60eu(NTSC), 720×576 50eu(PAL), 720 50P, 720 60P, 1080 50eu, 1080 60eu, 1080 24P, 1080 25P, 1080 30P, 1080 50P, diferite moduri sunt adaptive. |
Interfață HD | HDMI |
format de codare video | H.264 |
standardul de protecție | All-aluminiu radiator de tip șasiu, anti-coroziune, design rezistent la șocuri |
dimensiunea totală | 102*80*30mm(1w)/102*90*30mm(5W)/188*47*34mm(10W)/228*55*40mm(20W) |
Total Weight | ≤0.20KG (1W) / ≤0.27KG (5W) ≤1.5KG (10W) ≤2KG (20W) |
2: Receptor
Product parameters:
Portable multi-bandwidth HD receiver parameters | |
Primiți gama de frecvențe | 170-860MHz VHF&UHF |
lățimea de bandă de frecvență | 2/3/4/5/6/7/8MHz, facultativ |
Nivel de intrare RF | -94dBm ~ -15dBm (la 8M lățime de bandă)/-98dBm ~ -15dBm (at 2M bandwidth) |
impedanta de intrare RF | 50 ohmi |
conector de intrare RF | N cap |
metoda demodulare | COFDM |
Constellation way | QPSK, 16QAM, 64QAM (facultativ) |
corectarea erorilor înainte | 1/2,2/3,3/4,5/6,7/8 (facultativ) |
Numărul de transportatori | 2k, |
interval de protecție | 1/32,1/16,1/8,1/4 (facultativ) |
decodare video | MPEG-2MP@ML/H.264 |
screen aspect ratio | 4:3 16:9 |
Video output image | 720*576@8MHz 1080P@60P、50P、50eu、30P、 |
modul de ieșire audio | Stereo unbalanced 300/ 200mv |
Iesire audio | 2Iesire audio + 2ieșire video |
tensiune de operare | AC220V/DC12V <0.4A |
Temperatura de Operare | -20℃ ~ + 50 ℃ |
physical dimension | 136*115*35mm non-standard all-aluminum shell |
greutatea echipamentului | 0.35Kg |
4: Instructions for use
1: Transmiţător
- Functional area description
“FURNICĂ”: Transmitting antenna interface, please connect the antenna before powering on
“HDMI”: High-definition video input interface, input below 1080/50P
“Ctrl”: Transmitter tuner connection interface
“DC 12V”: DC12V power input port. “+” is the positive pole of the power supply, “-” is the negative pole of the power supply
“DC” este: Power indicator light, when the light is always on, it means that the power input of the transmitting module is normal
“TS”: Video input detection indicator light, this light is always on to indicate video input and normal encoding
- Parameter Configuration Description
Connect the transmitter parameter adjuster, press the “MENU/OK” key to enter the menu, the encryption key and data serial port parameters are displayed first, press the left or right key to move the cursor, and the up and down keys to adjust the parameters
After the parameter setting is completed, presa “MENU/OK” to enter the next menu, and the interface is displayed as shown in the figure
Press the left or right key to move the cursor, press the up or down key to adjust the required parameters, the interface prompts as shown in the figure
After all parameter settings are completed, press the “MENU/OK” key to confirm, and the display will be as shown in the figure.
After the setting is completed, the parameters are written successfully, and the display is as shown in the figure
- General Troubleshooting
A: The light is off after the power is turned on: Check whether the power input meets the standard
b: “TS” indicator light is off: Check the video input connection cable, check whether the video input format conforms, and check whether the camera is interfered with (you can judge by holding the antenna with your hand).
C: The temperature of the transmitter is very low: check whether the current is normal (the deviation can be ±0.2A within the standard current).
d: Three lights are always on, and one of them is super bright: it means that the transmitter has failed the detection, and you can try to power off and restart (uncommon)
2: Receptor
- Functional area description
“RF in1” “RF in2”: receiving antenna interface, it is recommended to connect the antenna and then turn on the power switch, because the static electricity of the human body may cause the receiver to crash.
“HDMI”: Video output interface, the output video format can be adjusted through the “HDMI” menu on the control panel.
“DC 12V”: Interfață de intrare de putere, please strictly follow the power supply voltage requirements, and overvoltage input is strictly prohibited
“ON / OFF”: power switch.
“USB”: video storage interface, when the U disk is inserted, press the “EXIT” button to start the video recording, after the recording is successful, the video display will display the video recording time, and the stored file name is “TS”.
- LCD parameter description
A:CH01 UNLOCKED(LCKED)
“CH01” means the channel number of the receiver, “UNLOCKED” means the received signal is unlocked, și “LCKED” means the signal is locked. “CH00” of the receiver is the initial writing channel, and the default channel corresponding to the normal operation of the transmitter is “CH001”
b: FREQ:602.0MHz
“602.0MHz” is the receiving frequency of the receiver, this frequency must be consistent with the frequency set by the transmitter, otherwise the receiver will not search or receive the signal from the transmitter
c: BW:6.0MHz
“BW” lățime de bandă, as shown in the figure, “BW: MHz” is understood as the RF bandwidth is 6MHz, this bandwidth must be consistent with the bandwidth set by the transmitter, otherwise the receiver will search for or cannot receive the signal from the transmitter
d: FEC:1/2
“FEC: 1/2” is the channel error correction, this parameter synchronizes the parameters set by the transmitter, and the receiver cannot be modified
e: soldat:1/32
“soldat:1/32” is the channel guard interval, this parameter is set by the transmitter synchronously, and the receiver cannot be modified
f:MAP: QPSK
“MAP: QPSK” is the modulation mapping, this parameter number is set by the transmitter synchronously, and the receiver cannot be modified
g: SNR:0.0dB(SNR:15.0dB)
“SNR: 15.0dB” is the signal quality (that is, the signal-to-noise ratio, the larger the value, the better). Cand “0.0dB” is displayed, the signal quality is 0, and the receiver will not be able to lock
“(SNR:15.0dB)” means the receiving signal-to-noise ratio is greater than 15dB. In the “QPSK” modulation mapping state, as long as the signal-to-noise ratio is greater than 6dB, the receiver can lock
h: PW:-72.1dBm(PW:-72.1)
PW is the received signal strength, (reference level value), the farther the transceiver end is relative to the distance, the weaker the signal strength is, and the larger the displayed value is, when the transmitter is not turned on, if the signal strength of the receiver is greater than -90dBm (such as -79.7dBm), it can be considered as adjacent frequency interference
- Parameter Configuration Description
Power on the receiver, and press the “MENU/OK” button to enter the menu, the first display is the menu of adjustable parameters, if you search for a specified frequency, directly press the “MENU/OK” button to enter the menu; if you want to remove the channel, press Press down to select “ListanbulChannel”, and then press “MENU/OK” to enter the menu operation; if you need to change the video output format, move the cursor to the “HDMI Mode” menu, presa “MENU/OK” to enter, and select the video to be output After formatting, press the “MENU/OK” key to confirm.
The frequency search method is as follows. After entering the frequency setting menu, the interface is displayed as shown in the figure. Press the left or right key to move the cursor, press the up or down key to adjust the frequency, lățime de bandă RF, and secret key that match the transmitter, and press the “MENU /OK” key to search. Note that the transmitter must be turned on at this time, in caz contrar, the receiver will not be able to lock because it cannot find the signal.
COFDM Mobile Video Wireless Transmission with a cheap price is including a transmitter and receiver for China directly
When the search is completed, presa “MENU/OK” a confirma, and the channel is saved in the register of the assistant board, as shown in the figure. To save the channel to the receiver register, press the “MENU/OK” key and the right key at the same time.
After the receiver parameter setting is completed, the functions of the panel keys are as follows
„↑”“↓“: each individually selectable receiver channel “CH**”
„←”“→“: You can choose to view the hidden parameters of the receiver
“EXIT”: start and stop recording
- Video function
Insert the storage device into the “USB” interface of the receiver, press the “EXIT” button to start recording, and a blue recording time box will appear on the upper left corner of the video display as shown below
- General Troubleshooting
A: The value after the receiver displays “-” is very low (Tx is not turned on): It means that the current channel has serious electromagnetic interference, and the normal value is -90- -100.
b: Cannot record video: check the U disk or replace the U disk.
C: No signal received: Check whether the channel frequency is consistent with the transmitter.
d: No video output: Check the connection line, power off, and restart to check whether there is a boot interface.