2 Watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter

2 ວັດ 5 ວັດ 10 Watts PA Linear Power Amplifier RF module board PCBA ສໍາລັບເຄື່ອງສົ່ງຂໍ້ມູນການເຊື່ອມຕໍ່ວິດີໂອໄຮ້ສາຍ

$450.00 – $980.00

ຕູ້ລໍາໂພງ

ຈະແຈ້ງ

ຂໍ ຄຳ ອ້າງ

SKU: ບໍ່ມີ ປະເພດ: ເຂດປ່າສະຫງວນ Power Amplifier

ຄໍາອະທິບາຍ
ສົ່ງການສອບຖາມ

2 ວັດ ຫຼື 5 ວັດ ຫຼື 10 watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter

ນີ້ແມ່ນສ່ວນສໍາຄັນຂອງເຄື່ອງສົ່ງວິດີໂອໄຮ້ສາຍ, ເຊິ່ງສາມາດຂະຫຍາຍສັນຍານ RF ສໍາລັບໄລຍະໄກ ແລະໄລຍະໄກ. ຖ້າຕ້ອງການ 1 Watt, 2 Watt, 5 Watt, ແລະ 10 Watt.

ສາລະບານ

ຄຸນລັກສະນະ

ແຖບຄວາມຖີ່: 800Mhz-830Mhz, 1425MHz-1455MH
RF ໃນ: 25± 2dBm
RF ອອກພະລັງງານ: 2 Watt (33dBm)
- 1400Mhz Transmitter gains 11dB when used with ໂມດູນເຊື່ອມຕໍ່ຂໍ້ມູນວິດີໂອໄຮ້ສາຍສອງທາງ, ຕັ້ງຄ່າພະລັງງານ RF ສູງສຸດເປັນ 22 ~ 24 dBm, then the RF out power will be 33~35 dBm.
- 800ການເພີ່ມຂຶ້ນຂອງ Mhz Transmitter: 13dB, when used with a two-way wireless video data link module, ຕັ້ງຄ່າພະລັງງານ RF ສູງສຸດເປັນ 20 ~ 22 dBm, then the RF out power will be 33~35 dBm.
RF ອອກພະລັງງານ: 5 Watt (37dBm)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, set up the maximum RF power as 22~25 dBm, then the RF out power will be 37~37 dBm.
- 800ການເພີ່ມຂຶ້ນຂອງ Mhz Transmitter: 17dB, when used with a two-way wireless video data link module, ຕັ້ງຄ່າພະລັງງານ RF ສູງສຸດເປັນ 20 ~ 22 dBm, then the RF out power will be 37~39 dBm.
RF ອອກພະລັງງານ: 10 Watt (40dBm)
- gain TX: 18dB, when used with a two-way wireless video data link module, set up the maximum RF power of as 22~24 dBm, then the RF out power will be 40~42dbm.
2 Watts Power in DC12V~16V;
5 Watts Power in DC24V~25V, minimum 1.8A@24V power current rating
10 Watts Power in DC24V~30V, minimum 2.5A@28V power current rating
2 Watts Power consumption: <6W ສະເລ່ຍ; 5 Watts Power consumption: <14W ສະເລ່ຍ; 10 Watts Power consumption: <28W ສະເລ່ຍ
2 ວັດ 5 Watts PCBA size: 46.5*31mm, ຄວາມຫນາຂອງ PCB: 1.2mm
10 Watts Dimensions: 65*62*13.5mm, not including the connector out of the metal housing, ນ້ໍາ: 98g
ຄວາມຕ້ານທານ: 50 ohm

ເຮັດວຽກຮ່ວມກັນກັບ ໂມດູນເຊື່ອມຕໍ່ຂໍ້ມູນວິດີໂອໄຮ້ສາຍສອງທາງ:

How to connect the PA power amplifier with the two way wireless video data link module — ວິທີການເຊື່ອມຕໍ່ເຄື່ອງຂະຫຍາຍສຽງ PA ກັບໂມດູນເຊື່ອມຕໍ່ຂໍ້ມູນວິດີໂອໄຮ້ສາຍສອງທາງ

Input RF

2 Watts PA Linear Power Amplifier RF module board PCBA RF input

RF ອອກ

2 Watts PA Linear Power Amplifier RF module board PCBA RF output — 2 Watts PA Linear Power Amplifier RF module board PCBA RF ຜົນຜະລິດ

ພະລັງງານໃນ	We should solder two bonding pads to connect with power VDD and GND.
ການຄວບຄຸມ	We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL ແລະ GND). ວັດສະດຸປ້ອນສູງ (1.8V ເຖິງ 3.3V) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode.
RF ໃນ	ຕົວເຊື່ອມຕໍ່ IPEX ສໍາລັບການເຊື່ອມຕໍ່ກັບເສົາອາກາດຕົ້ນຕໍຂອງໂມດູນເຊື່ອມຕໍ່ຂໍ້ມູນວິດີໂອໄຮ້ສາຍສອງທາງ.
RF ອອກ	We should solder the bonding pad to an antenna connector.

Housing case and assemble

We recommend that this power amplifier for our two-way wireless video data link OEM PCBA module.

To enhance the power amplifier in conjunction with our two-way wireless video data link module, we recommend you fabricate a metallic housing casing that aligns with your device’s architecture.

It should also leave at least 6mm between the PA board and the upper cover. In order to facilitate heat dissipation and establish an electrical grounding connection, the back side of the PA board must be directly and firmly attached to the metal.

Proper integration of heat dissipation techniques, such as a heat sink or fan, is essential for optimal performance in designs utilizing the PA OEM module.

We can also make a metal chamber for this PA module according to the customer’s requirement.

The below model has a built-in Power Amplifier inside.