Encoder Modulator Decoder Demodulator Module Parametre Talîmatên Veavakirinê Fermana COFDM AT
Encoder Modulator Decoder Demodulator Module Parametre Talîmatên Veavakirinê Fermana COFDM AT
Download the Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions below if you need a PDF file.
Update Record:
| Awa | Rojek | Terîf |
| 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 | 2016-10-24 2016-11-1 2016-12-26 2017-2-14 2017-2-28 2017-3-27 2017-4-19 2017-5-18 2017-9-12 2018-3-15 2019-6-25 2023-2-24 | Initial version ATDR reply distinguishing module ATSE, ATGE add audio switch Add ATSP protocol Add ATST, ATGT protocol ATGE command add AESfor status acquisition Added ATGB protocol AV and HDMI output control Support for obtaining the current AV output standard Added ATSU, ATGUcommands Added ATOSD, ATSIP, ATGIP commands Added ATSAD, ATGAD commands |
Users may need to modify the configuration parameters of the module during the use of the COFDM modulator and demodulator module. In order to simplify the user’s operation, we design the parameter configuration into a few simple AT commands. The user only needs to use the specified AT command and pass the corresponding parameters to complete the parameter setting of the COFDM module.
Suitable Models
-
Modula Repeaterê COFDM Relay ji bo veguhezkar û wergirê vîdyoyê ya bêserûber a drone UAV Vcan1870 -
COFDM Modulator Demodulator Module Encoder Dekoder HDMI CVBS AV Ketina AES 256 FHD RF weşana -
Veguhezkar û wergirê vîdyoyê ya bêtêl ji bo kamerayê, HDMI HD H265 264 encoder 1W / 2.5W PA 1080P60 Vcan1726 -
Modulatorê şîfrekerê SDI an HDMI Bo IP-yê CVBS H.265 H.264 panela kodkirina pcba Ethernet RSTP UDP ji bo UAV Drone Robotic
Command Introduction
The AT command for configuring COFDM module parameters starts with “AT” and ends with an underscore “_”. Each AT command has several or no parameters, and each AT command has a return value. For details, please refer to the introduction of the following commands.
Users can configure the parameters of the module through the configuration serial port (asta TTL, 3.3bike) of the COFDM module. For detailed serial port configuration, refer to the figure below. Please use tools such as “Serial Port Debugging Assistant” to send AT commands to the COFDM module, pay attention to the use of nivîstok, bo nimûne:
Command Classification
The AT commands for configuring COFDM module parameters are mainly divided into the following two categories:
| Query Commands | ATDR, ATGD, ATGE, ATGI , ATGR, ATGT, ATGB, ATGU, ATGIP |
| Setting Commands | ATSD, ATSG, ATSM, ATSE, ATSI, ATSO, ATSR, ATSP, ATST, ATSU,ATOSD, ATSIP |
From the perspective of whether to save after power-off, the setting commands can be divided into:
| Power-off Saving Commands | ATSD, ATSE, ATSI, ATSO, ATSR, ATSP, ATST, ATSU, ATSIP |
| Power-off Not Saving Commands | ATSG, ATSM, ATOSD |
According to the configuration transmitter or receiver, the classification is as follows:
| Sender Configuration Commands | ATDR, ATSD, ATGD, ATSG, ATSM, ATSE, ATGE, ATSI, ATGI, ATSO, ATSP, ATST, ATGT, ATSU, ATGU, ATOSD |
| Receiver Configuration Commands | ATDR, ATSR, ATGR, ATSP, ATST, ATGT, ATGB, ATSIP, ATGIP |
Command Details
Ping Command
| Çap | ATDR_ |
| parametreyê | Na |
| Bikaranîn | for the integrated system to check whether the serial port is connected and identify the connected modules. |
| Nirxa vegerê | RCB returns the “device profile” string SUE1 returns “ATDRSUE1 OK” string SHD1 returns “ATDRSHD1 OK” string |
| Bingotin | fermana pirsê |
Set Device Command
| Çap | ATSD $(mimo), $(gi), $(Hesabkirina rêjeya veguheztina pergala veguheztina wireless ya COFDM), $ (constellation), $(freq(KHz)), $(bw(KHz)), $(tx1_gain), $(tx2_gain)_ Mînak: ATSD0,1,0,0,800000,8000,86.0,86.0_ |
| parametreyê | One Antenna/Dual antenna mimo: 0 mimo disable; 1 mimo enable Guard Interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1/4 Convolution Code Rate: 0 1/2; 1 2 /3; 2 3/4; 3 5/6; 4 7/8; constellation: 0 QPSK; 1 QAM16; 2 QAM64; RCB Carrier Center Frequency(kHz) 200000~2700000(200MHz~2.7GHz, 1gavê KHz) RC900 Carrier center Frequency(kHz) 750000~930000(750MHz ~ 930MHz, 1gavê KHz) RCB Channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1gavê KHz) RCB Channel bandwidth bw(KHz) 2000~8000 (2MHz~8MHz, 1gavê KHz) Transmitting antenna 1 gain tx1_gain 0.0~89.75dB, 0.25dB gav avêtin Transmitting antenna 2 gain tx2_gain 0.0~89.75dB, 0.25dB gav avêtin |
| Nirxa Vegerê | wekî:ATSD0,1,0,0,800000,8000,86.0,86.0_ SISO,GI: 1/16, CR:1/2, MOD: QPSK, freq:800000KHz,bw:8000KHz,tx1_gain:86.000000 tx2_gain:86.000000 OK |
| Not | Set command, save when power off. Different Bandwidths, navberan de cerdewanek, Convolution code rates, Data rate calculation formulas corresponding to constellations Air interface rate Rate(Hesabkirina rêjeya veguheztina pergala veguheztina wireless ya COFDM) Hesabkirina rêjeya veguheztina pergala veguheztina wireless ya COFDM (Bandê(MHz) * 8.0/7.0) / (1+GI) * 1512/2048*Hesabkirina rêjeya veguheztina pergala veguheztina wireless ya COFDM(Hesabkirina rêjeya veguheztina pergala veguheztina wireless ya COFDM) * Hesabkirina rêjeya veguheztina pergala veguheztina wireless ya COFDM * 188/204. Taking 8MHz bandwidth as an example, different guard intervals, convolution code rates, data rates corresponding to constellations and required receiving signal-to-noise ratios  |
Set Gain Command
| Çap | ATSG$( tx1_gain),$( tx1_gain)_ Mînak: ATSG85.0,85.0_ |
| parametreyê | tx1_gain: Transmitter 1 qezenc tx2_gain: Transmitter 2 qezenc |
| Bikaranîn | To dynamically adjust the output power. If the signal SNR/RSSI of the receiver is high, the output power can be reduced through the remote control link. When the SNR/RSSI of the end signal is low, increase the output power (stefartî) |
| Nirxa Vegerê, | Mînak: ATSG85.0,85.0_set gain 85.000000 85.000000 OK |
| Bingotin | fermana sazkirinê, power off will not save. |
Set Modulation Mode command
| Çap | ATSM$(gi), $(Hesabkirina rêjeya veguheztina pergala veguheztina wireless ya COFDM), $(constellation)_ Mînak: ATSM1,1,2_ |
| parametreyê | Gard interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1 /4; Convolution code rate: 0 1/2; 1 2/3; 2 3/4; 3 5/6; 4 7/8; constellation: 0 QPSK; 1 QAM16; 2 QAM64 |
| Bikaranîn | Dynamically adjust the air interface rate, the air interface rate can be increased when the distance is short, and the air interface rate can be reduced when the distance is long (stefartî) |
| Nirxa Vegerê | Mînak:ATSM1,1,2_GI:1/16, CR:2/3, MOD: QAM64, OK |
| Bingotin | fermana sazkirinê, power off will not save. |
Get Device Status Command
| Çap | ATGD_ |
| parametreyê | Na |
| Bikaranîn | query the current number of transmit antennas, interval cerdevan, convolution code rate, number of constellations, transmit frequency, bandwidth, gain parameters (stefartî) |
| Nirxa Vegerê | Mînak: ATGD_ SISO, GI:1 /16, CR: 1/2, MOD: QPSK, freq: 800000KHz, bw: 8000KHz, tx1_gain: 86.000000 tx2_gain: 86.000000 OK |
| Bingotin | fermana pirsê |
Set Encoder Command
| Çap | ATSE$(llc),$(rt),$(bitrate) ,$(gop),$(audio)_ Mînak: ATSE0,0,0.0,0,0_ |
| parametreyê | 1. Enhanced data reliability option llc: 0 disable; 1 bikêrkirin (requires the receiving end to enable this option at the same time, use in pairs, because more redundant data is added to enhance reliability, the video bit rate of the transmitting end should be set when this option is turned off half of) 2. Real-time priority/quality priority rt: 0 image quality priority; 1 real-time priority; 3. Bitrate: 0 let system decide; >0 specify bitrate(float) 4. I frame interval GOP: 0 let system decide; >0 specify GOP 5. Audio encoding option audio: 0 disable; 1 bikêrkirin |
| Bikaranîn | Used to set encoding parameters (Transmitter) |
| Nirxa Vegerê | Mînak:ATSE0, 0,0.0,0,0_ AWA:0,RT:0,bitrate: 0.0Mbps,gop:0,audio:0,OK |
| Bingotin | fermana sazkirinê, save when power is off. |
Get Encoder Command
| Çap | ATGE_ |
| parametreyê | Na |
| Bikaranîn | querying encoding parameters (sending end) |
| Nirxa Vegerê | Mînak:ATGE_MODE:0, RT:0,bitrate:4.0Mbps,gop:10,audio:0,aes:0, OK |
| Bingotin | Query command AES means the current encryption status: 0 disable; 1 bikêrkirin |
Get Input Command
| Çap | ATGI_ |
| parametreyê | Na |
| Bikaranîn | query the current camera input parameters (stefartî) |
| Nirxa Vegerê | Mînak:ATGI_input_size: 1080p, input_rate: 60fps, sensor_type: hdmi,OK |
| Bingotin | fermana pirsê |
Set Input Command
| Çap | ATSI$(input_size),$(input_rate)_ Mînak: ATSI1080,25_ |
| parametreyê | 1. Input resolution input_size: 0 bila pergal tespît bike; >0 specify input size 2. Input frame rate input_rate: 0 bila pergal tespît bike; > 0 specify input fps |
| Bikaranîn | To specify the input resolution and frame rate to meet some special signal sources, or some special application needs (stefartî) |
| Nirxa Vegerê | Mînak: ATSI1080,25_ Input_size:1080p,input_rate: 25fps, OK |
| têbînî | After the user specifies the input resolution and frame rate through this command, the system will no longer detect the signal source (use with caution). The user can restore the default through the following command: ATSI0,0_Set the command and save it after power-off. |
Set Output Command
| Çap | ATSO$(output_size),$(output_rate)_ Mînak: ATSO720,30_ |
| parametreyê | 1. Transmitter: encoding output resolution output_size: 0 equal to input_size; >0 specify output size 2. Receiver: HDMI output resolution (720, 1080) 3. Transmitter: encoding output frame rate output_rate: 0 equal to input_rate; >0 specify output_rate (fps) 4. Receiver: HDMI output frame rate 720p supports frame rate (50, 60); 1080p supports frame rate (24, 25, 30, 50, 60) |
| Bikaranîn | 1. Transmitter: Used to specify the encoding output resolution and frame rate to meet the requirements of certain applications for zooming and frame reduction 2. Receiver: used to configure the resolution and frame rate of HDMI output |
| Nirxa Vegerê | Mînak: ATSO720,30_ output_size: 720p, output_rate: 30fps, OK |
| têbînî | 1. For HDMI input only, this command is invalid for AV input 2. Output_size <= input_size; output_rate<=input_rate 3. Set the command and save it after the power is off. |
Fermana Çavkaniyên Input Set (biguherîne HDMI / input CVBS)
| Çap | ATSU$(vin),$(ain)_ Mînak: ATSU0,1_ |
| parametreyê | 1. Hilbijartina têketina vîdyoyê VIN: 0 bila pergal tespît bike; 1 input CVBS zorê; 2 zorê hdmi / input SDI 2. Hilbijartina têketina deng AIN: 0 bila pergal tespît bike; 1 hêza input analog |
| Bikaranîn | Ji bo pêkanîna daxwazên serîlêdanê yên taybetî tê bikar anîn (Mînak: Vîdyoya têketina HDMI / SDI, dengê têketina MIC) |
| Nirxa Vegerê | Mînak: ATSU0,1_ ATSU0,1 OK |
| Bingotin | fermana sazkirinê, hêza-off xilas bike. |
Get User Command
| Çap | ATGU _ Mînak: ATGU_ |
| parametreyê | Na |
| Bikaranîn | To query user-specific configuration |
| Nirxa Vegerê | Mînak: ATGU_ ATGU0,1 OK |
| Bingotin | fermana pirsê return parameter description please refer to the ATSU command |
Set Receiver Command
| Çap | ATSR $(freq), $(bw ), $(llc), $(cvbs)_ Mînak: ATSR320000,6000,0,0_ |
| parametreyê | 1. DR2C carrier frequency freq(KHz) 200000~860000(200MHz ~ 860MHz, 1gavê KHz) 2. DR900 carrier center frequency freq(KHz) 200000~1600000(200MHz~1.6GHz, 1gavê KHz) 3. DR2C channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1gavê KHz) 4. DR900 channel bandwidth bw(KHz) 3200~8000(3.2MHz~8MHz, 1gavê KHz) 5. Enhanced data reliability option llc: 0 disable; 1 bikêrkirin (it is required that the transmitter should also enable this option at the same time, and use it in pairs. Since more redundant data is added to enhance reliability, the video bit rate of the transmitter should be set to when this option is turned off half of) 6. AV output system cvbs: 0 pal; 1 ntsc |
| Bikaranîn | To set the receiver parameter |
| Nirxa Vegerê | example: ATSR320000,6000,0,0_ ATSR320000,6000,0,0 OK |
| Bingotin | fermana sazkirinê, save when power is off. |
Get Receiver Command
| Çap | ATGR_ |
| parametreyê | Na |
| ATGR_ | the receiving end parameter |
| Nirxa Vegerê | Mînak: ATGR_ ATGR320000,6000,0,aes:0,cvbs:0 OK |
| Bingotin | 1. Query command 2. Aes parameter indicates the current encryption status: 0 disable;1 bikêrkirin 3. CVBS parameter Indicates the current AV output standard: 0 pal;1 ntsc |
Get Bit Error Rate Command
| Çap | ATGB_ |
| parametreyê | Na |
| Bikaranîn | querying the bit error rate and signal strength of the dual antennas at the receiving end |
| Nirxa Vegerê | Mînak: ATGB_ ATGB ber1:0.00% ber2:0.00% RSSI1 :54 RSSI2:53 Lock1:1 Lock2:1 OK |
| têbînî | 1. Query commands 2. Ber1 and ber2 respectively indicate the bit error rate of each antenna, ji 0.0% ber 100.0% 3. RSSI1 and RSSI2 respectively indicate the signal strength of each antenna, ji 0 ber 100 4. Lock1 and Lock2 respectively indicate the signal locking status of each antenna (1 Represents signal lock) |
Set Password Command
| Çap | ATSP$(şîfre), $(şîfre)_ Mînak: ATSP123456, 123456_ |
| parametreyê | AES key password: 6-şîfreya hejmarî (ASCII) AES key password: 6-şîfreya hejmarî (ASCII) (repeat it for confirmation) |
| Bikaranîn | Used to set the AES key of the transceiver (stefartî û destikê) |
| Nirxa Vegerê | Mînak: ATSP123456_ ATSP123456 OK |
| Bingotin | 1. When the password is all 0, AES encryption is turned off. 2. Set the command and save it after powering it off. |
Set Data Transfer Command
| Çap | ATST$(rêjeya baud), $( parity)_ Mînak: ATST115200,0_ |
| parametreyê | 1. Baud rate baud rate: 1200、2400、4800、9600、19200、38400、57600、115200 2. Check Code: 0: Netû; 1: Ecêb; 2: Hetta |
| Bikaranîn | Used to set the baud rate and parity bit of the serial port for data transparent transmission |
| Nirxa Vegerê | Mînak: ATST115200,0_ ATST115200,0 OK |
| têbînî | Set command |
Get Data Transfer Command
| Çap | ATGT_ |
| parametreyê | Na |
| Bikaranîn | Used to query the baud rate and check code |
| Nirxa Vegerê | Mînak: ATGT_ ATGT115200,0 OK |
| têbînî | Query command |
Set IP Address Command
| Çap | ATSIP$(ip), $(ip)_ Mînak: ATSIP192.168.1.215,192.168.1.215_ |
| Parametreyên | Local IP address Local IP address (repeat to confirm) |
| Bikaranîn | Used to set the receiver IP address |
| Nirxa Vegerê | Mînak: ATSIP_192.168.1 .215,192.168.1.215_ ATSIP192.168.1.215 OK |
| têbînî | 1. After setting the IP address, the receiving end needs to be restarted to take effect. 2. Set the command and save it after powering it off. |
Get IP Address Command
| Çap | ATGIP_ Mînak: ATGIP_ |
| parametreyê | Na |
| Bikaranîn | ji bo ku navnîşana IP-ya heyî ya dawiya wergirtinê bipirsin |
| Nirxa vegerê | Mînak: ATGIP_ ATGIP192.168.0.215 OK |
| Bingotin | fermana pirsê |
OSD Overlay Protocol
| Çap | ATOSD$(idx), $(x), $(y), $(str)_ Mînak:ATOSD0,40,20,height: 100m_ |
| parametreyê | 1. IDX index: 0~7 (supports OSD overlay for 8 areas) 2. X-coordinate: 0~1919 3. Y coordinate: 0~1079 4. str: the string to be displayed at the corresponding coordinates (the space symbol is used to clear the display) |
| Bikaranîn | on the video screen.OSD information |
| Nirxa vegerê | Na |
| têbînî | 1. The user specifies the x and y coordinates of the OSD display according to the maximum 1920×1080 pixels, and the system will correct the coordinates according to the actual display situation. 2. The ‘_’ character cannot be contained in the str parameter |
Set Gain To Adjust
| Çap | ATSAD$(freq),$(adjust) _ Mînak:ATSAD700000,2.5_ |
| parametreyê | wireless central working frequency： Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) Adjust the value(dB): ATSD cmd will subtract this value to set the wireless gain |
| Karî | Specify and adjust the value for the wireless gain setting using by ATSD cmd |
| Feedback | Mînak: ATSAD700000,2.5_ freq:700000,adjust:2.50 OK |
| Comments | Setting command is still valid when stopping power or resetting. |
Get Gain To Adjust
| Çap | ATGAD[$(freq)]_ Mînak:ATGAD700000_ |
| parametreyê | wireless central working frequency： Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) When no parameter provides, it will list all the freq that have adjusted value. |
| Karî | Inquiry adjust the value for wireless gain setting using ATSD cmd |
| Feedback | Mînak: ATGAD700000_ freq:700000,adjust:2.50 OK ATGAD_ freq:700000 750000 OK |
| Comments | Inquiry command. |
Serial Port Utility software download
https://www.alithon.com/downloads
Pirs û Bersîv
1. How can I return to the No Password setting with 000000 indications after the change?
Reset the password to 000000 (one must not be missing) through the Parameter Configuration Panel Board.
or set it through ew ATSP_command
2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (Qezenc) good for linear output operation? Or do you suggest some limited range for better linear operation?
The Gain of the COFDM configuration is the internal Gain, not the actual output power of the transmitter. The internal gain range is 0~89.75dB and the linear output:
1. At around 300~500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -5dBm.
2. At around 1000~1500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -6dBm to -10dBm.
3. I tried to set – B bandwidth (kHz) and E bit rate (Mbps). When I set E, the new value does not apply. Wiha. the E setting is only for monitoring of available bitrate? if I wish to change the E (Bitrate) I have to change only B (bandwidth)? Am I right?
It is not recommended to modify the video bit rate ‘E’ directly, because if the output video bit rate is greater than the wireless air interface rate, the system will not work normally.
Bi xwerû, the internal video bit rate ‘E’ will be set to 0 for automatic. Customers only need to modify ‘B’ to modify the wireless parameters, and the video bit rate will automatically adapt.
You can also adjust the wireless air interface rate by modifying GI and CR.
For more details on the Encoder Modulator Decoder Demodulator Module, please send an inquiry to us.
COFDM Modulator Demodulator Module Encoder Dekoder HDMI CVBS AV Ketina AES 256 FHD RF weşana
$0.00
COFDM Modulator Demodulator Module Encoder Dekoder HDMI CVBS AV Ketina AES 256 FHD RF weşana
Tabloya naverokê
Dîmenek din
Modula kodkera COFDM, CVBS / input HDMI, derketina IP
Ji bo Zêdetir hûrgulî di derbarê panela kodkera COFDM de, ji kerema xwe biçin vir
Advantage module COFDM Encoder:
- Derengiya pir kêm H.265/H.264 kodkirina deng û vîdyoyê ya herî zêde piştgirî dike 1080P@60 girtina vîdyoyê ya rast-dem û şîfrekirinê
- Têketina deng û vîdyoyê HDMI an AV, piştî şîfrekirinê, derana porta Ethernet an Derketina modula wireless, rêjeya bit şîfrekirina vîdyoyê dikare bi dînamîkî were mîheng kirin
- Piştgiriya input audio û encam Decoding audio
- Du vîdyoyan piştgirî bikin (HDMI + AV) encoding hevdemî (dibe, default şîfrekirina HDMI an AV e, yek ji du çavkaniya têketinê hilbijêrin). )
- Web UI an emrê porta serial UART AT ji bo birêvebirina veavakirinê
Modula veguhestina COFDM
Daxistina pelgeya daneya modulator-demodulator COFDM
Daneyên demodulatorê COFDM Vcan1776RX-H264
Guhertoya paşîn a panela TX RX
TX: V6.5.6p
RX: 4.1.2p
FAQs
- Pirs 1: Ji kerema xwe hûn dikarin ji min re jimareya beşê ya vê beşê vebêjin, em hewl didin ku herêmî bibînin û kontrol bikin. Bersiv 1: Ew induktansek bi navê LOH32PN2R2NNC e.
- Xalên kontrolê pêşniyar bikin: Ger heyama dabînkirina hêzê ya panelê baş be lê derneya RF tune be, dibe ku pêkhateya jêrîn TC1-1-13MX+ bi giştî zerar e.
- Ji bo ku di dema veguhastinê de zirarê nede vê amûrê (amûrê xwe bi nisbeten bilind e), me ferman da parastina benîştê sor ji bo vê cîhazê dema ku me ew şand.
- Endezyar her weha pêşniyar dike ku hûn kontrol bikin ka kablo sist e an di têkiliyek xirab de ye.
- Ji kerema xwe hewl bidin ku kabloya FPC ya ku her du panelan girêdide biguhezînin
- We can provide spare parts if you're sure which one.
Emîn
Ji kerema xwe lînka jêrîn kontrol bikin.
Encoder Modulator Decoder Demodulator Module Parametre Talîmatên Veavakirinê Fermana COFDM AT
3. Pirs, Ger kalîteya kamera me ji bo herduyan jî têra xwe baş e 4 MHz û 8 bandwidth MHz. Di vê rewşê de, Divê xerîdar hilbijêre 4 MHz an 8 MHz?
Bersiv: Sewqiyatên me yên COFDM-ê yên yek-alî ji hêla xwerû ve bandpêda bêserûber 4Mz bikar tînin, bi rêjeya bit-a vîdyoyê ya 3.12Mbps re têkildar e, ku ji bo 1080p bes e; Ger di heman şert û mercan de berbaya bêserûber a 8MHz were guheztin, rêjeya bit video ducarî 6,24Mbps. Hemî xerîdar dikarin di navbera 4MHz û 8MHz bandwidahiya wireless de hilbijêrin, 6MHz jî dikare were hesibandin.
4. Pirs: Ji bo vê setê tx + rx ji nêrînek hestiyariyê ya wergirtinê kîjan çêtir e?
Bersiv: Ji bo girêdanên wireless, meriv dikare bi hêsanî were hesibandin ku hesasiya wergirtinê dê di bendavên bêserûber ên jêrîn de bilindtir be. Ji perspektîfa wergirtina hestiyariyê, 4MHz>6MHz>8MHz
Emîn
Ji kerema xwe lînka jêrîn kontrol bikin
Modula Repeaterê COFDM Relay ji bo veguhezkar û wergirê vîdyoyê ya bêserûber a drone UAV Vcan1870
Hesasiya wergirtina kanala yekane:
-97+/-1DBM li QPSK 8MHz,
-98+/-1DBM li QPSK 6MHZ,
Dema ku bi antenên dualî distînin hestiyar bi 3dbm zêde bû
Firmwareya xwerû ya wergirê lîstikvanê RTSP piştgirî dike, hin xerîdar lîstikvanê UDP tercîh dikin, ku em jî dikarin pêşkêş bikin, then RTSP player doesn't support. (RTSP û UDP tenê dikarin yek ji du firmware hilbijêrin)
Ji kerema xwe li ser lînka jêrîn dakêşin.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
Emîn, ji kerema xwe wêneyê jêrîn kontrol bikin.
Meriv çawa bi fermana UART AT ve têketina vîdyoya HDMI an CVBS veguherîne?
Meriv çawa wergirê vîdyoyê COFDM nûve dike
Meriv çawa panela modulatorê kodkera vîdyoya drona COFDM nûve dike
SDI + AHD + CVBS Vîdyo Koder û H264 H265 dekoder
Hin xerîdar jî pêdivî bi SDI AHD CVBS kodkerê vîdyoyê modulatorê veguhezkarê vîdyoyê dekodera demodulatorê wergirê HDMI-yê heye. Di heman demê de modelek me ya din jî heye Vcan1776-SDI+AHD+CVBS van fonksiyonan piştgirî dike.
Kîjan panela dekodera vîdyoyê H264 H265 û derengiya pir kêm piştgirî dike?
Tabloya dekodera şîn a milê çepê piştgirî dide dekodkirina H265 û H264 lê dekodkirina kêm-dereng piştgirî nake. (Samsun Chipset)
Tabloya reş a rastê piştgirî dide dekodkirina H264 lê piştgirî dide dekodkirina H264-derengiya kêm. (HiSilicon)
| Input Video | HDMI + CVBS, SDI + AHD + CVBS |
|---|
Biba yên pêşî go revue de "COFDM Modulator Demodulator Module Encoder Dekoder HDMI CVBS AV Ketina AES 256 FHD RF weşana”
berhemên Related
Modula TX RX
FPV Veguhastera Vîdyoyê Analog CVBS Modula vîdyoya dengî şanderê 400-900MHz UHF vcan1904
Reviews
are no reviews hene yet.