Encoder Modulator Decoder Demodulator Module Parameter Οδηγίες διαμόρφωσης COFDM AT Command
Download the Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions below if you need a PDF file.
Update Record:
Εκδοχή | Ημερομηνία | Περιγραφή |
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 | 2016-10-24 2016-11-1 2016-12-26 2017-2-14 2017-2-28 2017-3-27 2017-4-19 2017-5-18 2017-9-12 2018-3-15 2019-6-25 2023-2-24 | Initial version ATDR reply distinguishing module ATSE, ATGE add audio switch Add ATSP protocol Add ATST, ATGT protocol ATGE command add AESfor status acquisition Added ATGB protocol AV and HDMI output control Support for obtaining the current AV output standard Added ATSU, ATGUcommands Added ATOSD, ATSIP, ATGIP commands Added ATSAD, ATGAD commands |
Users may need to modify the configuration parameters of the module during the use of the COFDM modulator and demodulator module. In order to simplify the user’s operation, we design the parameter configuration into a few simple AT commands. The user only needs to use the specified AT command and pass the corresponding parameters to complete the parameter setting of the COFDM module.
Suitable Models
Command Introduction
The AT command for configuring COFDM module parameters starts with “AT” and ends with an underscore “_”. Each AT command has several or no parameters, and each AT command has a return value. For details, please refer to the introduction of the following commands.
Users can configure the parameters of the module through the configuration serial port (επίπεδο TTL, 3.3V) of the COFDM module. For detailed serial port configuration, refer to the figure below. Please use tools such as “Serial Port Debugging Assistant” to send AT commands to the COFDM module, pay attention to the use of κείμενο, για παράδειγμα:
ντοommand Classification
The AT commands for configuring COFDM module parameters are mainly divided into the following two categories:
Query Commands | ATDR, ATGD, ATGE, ATGI , ATGR, ATGT, ATGB, ATGU, ATGIP |
Setting Commands | ATSD, ATSG, ATSM, ATSE, ATSI, ATSO, ATSR, ATSP, ATST, ATSU,ATOSD, ATSIP |
From the perspective of whether to save after power-off, the setting commands can be divided into:
Power-off Saving Commands | ATSD, ATSE, ATSI, ATSO, ATSR, ATSP, ATST, ATSU, ATSIP |
Power-off Not Saving Commands | ATSG, ATSM, ATOSD |
According to the configuration transmitter or receiver, the classification is as follows:
Sender Configuration Commands | ATDR, ATSD, ATGD, ATSG, ATSM, ATSE, ATGE, ATSI, ATGI, ATSO, ATSP, ATST, ATGT, ATSU, ATGU, ATOSD |
Receiver Configuration Commands | ATDR, ATSR, ATGR, ATSP, ATST, ATGT, ATGB, ATSIP, ATGIP |
Command Details
Ping Command
Μορφή | ATDR_ |
παράμετρος | Οχι |
Χρήση | for the integrated system to check whether the serial port is connected and identify the connected modules. |
Επιστρεφόμενη αξία | RCB returns the “device profile” string SUE1 returns “ATDRSUE1 OK” string SHD1 returns “ATDRSHD1 OK” string |
Παρατήρηση | εντολή ερωτήματος |
Set Device Command
Μορφή | ATSD $(mimo), $(gi), $(Κεντρικό σημείο συχνότητας λειτουργίας), $ (constellation), $(συχν(KHz)), $(bw(KHz)), $(tx1_gain), $(tx2_gain)_ Παράδειγμα: ATSD0,1,0,0,800000,8000,86.0,86.0_ |
παράμετρος | One Antenna/Dual antenna mimo: 0 mimo disable; 1 mimo enable Guard Interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1/4 Convolution Code Rate: 0 1/2; 1 2 /3; 2 3/4; 3 5/6; 4 7/8; σχηματισμού: 0 QPSK; 1 QAM16; 2 QAM64; RCB Carrier Center Frequency(kHz) 200000~2700000(200MHz~2.7GHz, 1Βήμα KHz) RC900 Carrier center Frequency(kHz) 750000~930000(750MHz ~ 930Mhz, 1Βήμα KHz) RCB Channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1Βήμα KHz) RCB Channel bandwidth bw(KHz) 2000~8000 (2MHz~8MHz, 1Βήμα KHz) Transmitting antenna 1 gain tx1_gain 0.0~89.75dB, 0.25dB stepping Transmitting antenna 2 gain tx2_gain 0.0~89.75dB, 0.25dB stepping |
Return Value | όπως:ATSD0,1,0,0,800000,8000,86.0,86.0_ SISO,GI: 1/16, CR:1/2, MOD: QPSK, συχν:800000KHz,bw:8000KHz,tx1_gain:86.000000 tx2_gain:86.000000 Εντάξει |
Σημείωση | Set command, save when power off. Different Bandwidths, διαστήματα Φρουράς, Convolution code rates, Data rate calculation formulas corresponding to constellations Air interface rate Rate(Κεντρικό σημείο συχνότητας λειτουργίας) Κεντρικό σημείο συχνότητας λειτουργίας (Εύρος ζώνης(MHz) * 8.0/7.0) / (1+GI) * 1512/2048*Κεντρικό σημείο συχνότητας λειτουργίας(Κεντρικό σημείο συχνότητας λειτουργίας) * Κεντρικό σημείο συχνότητας λειτουργίας * 188/204. Taking 8MHz bandwidth as an example, different guard intervals, convolution code rates, data rates corresponding to constellations and required receiving signal-to-noise ratios |
μικρόet Gain Command
Μορφή | ATSG$( tx1_gain),$( tx1_gain)_ Παράδειγμα: ATSG85.0,85.0_ |
παράμετρος | tx1_gain: Πομπός 1 κέρδος tx2_gain: Πομπός 2 κέρδος |
Χρήση | To dynamically adjust the output power. If the signal SNR/RSSI of the receiver is high, the output power can be reduced through the remote control link. When the SNR/RSSI of the end signal is low, increase the output power (πομπός) |
Return Value, | Παράδειγμα: ATSG85.0,85.0_set gain 85.000000 85.000000 Εντάξει |
Παρατήρηση | setting command, power off will not save. |
Set Modulation Mode commanρε
Μορφή | ATSM$(gi), $(Κεντρικό σημείο συχνότητας λειτουργίας), $(constellation)_ Παράδειγμα: ATSM1,1,2_ |
παράμετρος | Gard interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1 /4; Convolution code rate: 0 1/2; 1 2/3; 2 3/4; 3 5/6; 4 7/8; σχηματισμού: 0 QPSK; 1 QAM16; 2 QAM64 |
Χρήση | Dynamically adjust the air interface rate, the air interface rate can be increased when the distance is short, and the air interface rate can be reduced when the distance is long (πομπός) |
Return Value | Παράδειγμα:ATSM1,1,2_GI:1/16, CR:2/3, MOD: QAM64, Εντάξει |
Παρατήρηση | setting command, power off will not save. |
σολet Device Status Command
Μορφή | ATGD_ |
παράμετρος | Οχι |
Χρήση | query the current number of transmit antennas, διάστημα φύλαξης, convolution code rate, number of constellations, transmit frequency, εύρος ζώνης, gain parameters (πομπός) |
Return Value | Παράδειγμα: ATGD_ SISO, GI:1 /16, CR: 1/2, MOD: QPSK, συχν: 800000KHz, bw: 8000KHz, tx1_gain: 86.000000 tx2_gain: 86.000000 Εντάξει |
Παρατήρηση | εντολή ερωτήματος |
Set Encoder Command
Μορφή | ATSE$(llc),$(rt),$(bitrate) ,$(gop),$(ήχου)_ Παράδειγμα: ATSE0,0,0.0,0,0_ |
παράμετρος | 1. Enhanced data reliability option llc: 0 disable; 1 enable (requires the receiving end to enable this option at the same time, use in pairs, because more redundant data is added to enhance reliability, the video bit rate of the transmitting end should be set when this option is turned off half of) 2. Real-time priority/quality priority rt: 0 image quality priority; 1 real-time priority; 3. Νιτρικά: 0 let system decide; >0 specify bitrate(float) 4. I frame interval GOP: 0 let system decide; >0 specify GOP 5. Audio encoding option audio: 0 disable; 1 enable |
Χρήση | Used to set encoding parameters (Πομπός) |
Return Value | Παράδειγμα:ATSE0, 0,0.0,0,0_ ΤΡΟΠΟΣ:0,RT:0,bitrate: 0.0Mbps,gop:0,ήχου:0,Εντάξει |
Παρατήρηση | setting command, save when power is off. |
Get Encoder Command
Μορφή | ATGE_ |
παράμετρος | Οχι |
Χρήση | querying encoding parameters (sending end) |
Return Value | Παράδειγμα:ATGE_MODE:0, RT:0,bitrate:4.0Mbps,gop:10,ήχου:0,aes:0, Εντάξει |
Παρατήρηση | Query command AES means the current encryption status: 0 disable; 1 enable |
Get Input Command
Μορφή | ATGI_ |
παράμετρος | Οχι |
Χρήση | query the current camera input parameters (πομπός) |
Return Value | Παράδειγμα:ATGI_input_size: 1080Π, input_rate: 60fps, sensor_type: HDMI,Εντάξει |
Παρατήρηση | εντολή ερωτήματος |
Set Input Command
Μορφή | ATSI$(input_size),$(input_rate)_ Παράδειγμα: ATSI1080,25_ |
παράμετρος | 1. Input resolution input_size: 0 let the system detect; >0 specify input size 2. Input frame rate input_rate: 0 let the system detect; > 0 specify input fps |
Χρήση | To specify the input resolution and frame rate to meet some special signal sources, or some special application needs (πομπός) |
Return Value | Παράδειγμα: ATSI1080,25_ Input_size:1080Π,input_rate: 25fps, Εντάξει |
Παρατηρήσεις | After the user specifies the input resolution and frame rate through this command, the system will no longer detect the signal source (use with caution). The user can restore the default through the following command: ATSI0,0_Set the command and save it after power-off. |
Set Output Command
Μορφή | ATSO$(output_size),$(output_rate)_ Παράδειγμα: ATSO720,30_ |
παράμετρος | 1. Πομπός: encoding output resolution output_size: 0 equal to input_size; >0 specify output size 2. Δέκτης: HDMI output resolution (720, 1080) 3. Πομπός: encoding output frame rate output_rate: 0 equal to input_rate; >0 specify output_rate (fps) 4. Δέκτης: HDMI output frame rate 720p supports frame rate (50, 60); 1080p supports frame rate (24, 25, 30, 50, 60) |
Χρήση | 1. Πομπός: Used to specify the encoding output resolution and frame rate to meet the requirements of certain applications for zooming and frame reduction 2. Δέκτης: used to configure the resolution and frame rate of HDMI output |
Return Value | Παράδειγμα: ATSO720,30_ output_size: 720Π, output_rate: 30fps, Εντάξει |
Παρατηρήσεις | 1. For HDMI input only, this command is invalid for AV input 2. Output_size <= input_size; output_rate<=input_rate 3. Set the command and save it after the power is off. |
Set Input Sources Command (switch HDMI / εισόδου CVBS)
Μορφή | ATSU$(vin),$(ain)_ Παράδειγμα: ATSU0,1 _ |
παράμετρος | 1. Video input selection VIN: 0 let the system detect; 1 force CVBS input; 2 force hdmi/SDI input 2. Audio input selection AIN: 0 let the system detect; 1 force analog input |
Χρήση | Used to meet specific application requirements (Παράδειγμα: HDMI/SDI input video, MIC input audio) |
Return Value | Παράδειγμα: ATSU0,1_ ATSU0,1 OK |
Παρατήρηση | setting command, power-off save. |
Get User Command
Μορφή | ATGU _ Παράδειγμα: ATGU_ |
παράμετρος | Οχι |
Χρήση | To query user-specific configuration |
Return Value | Παράδειγμα: ATGU_ ATGU0,1 OK |
Παρατήρηση | εντολή ερωτήματος return parameter description please refer to the ATSU command |
Set Receiver Command
Μορφή | ATSR $(συχν), $(bw ), $(llc), $(cvbs)_ Παράδειγμα: ATSR320000,6000,0,0_ |
παράμετρος | 1. DR2C carrier frequency freq(KHz) 200000~860000(200MHz ~ 860MHz, 1Βήμα KHz) 2. DR900 carrier center frequency freq(KHz) 200000~1600000(200MHz~1.6GHz, 1Βήμα KHz) 3. DR2C channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1Βήμα KHz) 4. DR900 channel bandwidth bw(KHz) 3200~8000(3.2MHz~8MHz, 1Βήμα KHz) 5. Enhanced data reliability option llc: 0 disable; 1 enable (it is required that the transmitter should also enable this option at the same time, and use it in pairs. Since more redundant data is added to enhance reliability, the video bit rate of the transmitter should be set to when this option is turned off half of) 6. AV output system cvbs: 0 pal; 1 ntsc |
Χρήση | To set the receiver parameter |
Return Value | example: ATSR320000,6000,0,0_ ATSR320000,6000,0,0 OK |
Παρατήρηση | setting command, save when power is off. |
Get Receiver Command
Μορφή | ATGR_ |
παράμετρος | Οχι |
ATGR_ | the receiving end parameter |
Return Value | Παράδειγμα: ATGR_ ATGR320000,6000,0,aes:0,cvbs:0 Εντάξει |
Παρατήρηση | 1. Query command 2. Aes parameter indicates the current encryption status: 0 disable;1 enable 3. CVBS parameter Indicates the current AV output standard: 0 pal;1 ntsc |
Get Bit Error Rate Command
Μορφή | ATGB_ |
παράμετρος | Οχι |
Χρήση | querying the bit error rate and signal strength of the dual antennas at the receiving end |
Return Value | Παράδειγμα: ATGB_ ATGB ber1:0.00% ber2:0.00% RSSI1 :54 RSSI2:53 Lock1:1 Lock2:1 Εντάξει |
Παρατηρήσεις | 1. Query commands 2. Ber1 and ber2 respectively indicate the bit error rate of each antenna, ranging from 0.0% προς την 100.0% 3. RSSI1 and RSSI2 respectively indicate the signal strength of each antenna, ranging from 0 προς την 100 4. Lock1 and Lock2 respectively indicate the signal locking status of each antenna (1 Represents signal lock) |
Set Password Command
Μορφή | ATSP$(password), $(password)_ Παράδειγμα: ATSP123456, 123456_ |
παράμετρος | AES key password: 6-digit password (ASCII) AES key password: 6-digit password (ASCII) (repeat it for confirmation) |
Χρήση | Used to set the AES key of the transceiver (πομπός και δέκτης) |
Return Value | Παράδειγμα: ATSP123456_ ATSP123456 OK |
Παρατήρηση | 1. When the password is all 0, AES encryption is turned off. 2. Set the command and save it after powering it off. |
Set Data Transfer Command
Μορφή | ATST$(ρυθμός baud), $( parity)_ Παράδειγμα: ATST115200,0_ |
παράμετρος | 1. Baud rate baud rate: 1200、2400、4800、9600、19200、38400、57600、115200 2. Check Code: 0: Κανένας; 1: Odd; 2: Even |
Χρήση | Used to set the baud rate and parity bit of the serial port for data transparent transmission |
Return Value | Παράδειγμα: ATST115200,0_ ATST115200,0 OK |
Παρατηρήσεις | Set command |
Get Data Transfer Command
Μορφή | ATGT_ |
παράμετρος | Οχι |
Χρήση | Used to query the baud rate and check code |
Return Value | Παράδειγμα: ATGT_ ATGT115200,0 OK |
Παρατηρήσεις | Query command |
Set IP Address Command
Μορφή | ATSIP$(ip), $(ip)_ Παράδειγμα: ATSIP192.168.1.215,192.168.1.215_ |
Παράμετροι | Local IP address Local IP address (repeat to confirm) |
Χρήση | Used to set the receiver IP address |
Return Value | Παράδειγμα: ATSIP_192.168.1 .215,192.168.1.215_ ATSIP192.168.1.215 OK |
Παρατηρήσεις | 1. After setting the IP address, the receiving end needs to be restarted to take effect. 2. Set the command and save it after powering it off. |
Get IP Address Command
Μορφή | ATGIP_ Παράδειγμα: ATGIP_ |
παράμετρος | Οχι |
Χρήση | για να ρωτήσετε την τρέχουσα διεύθυνση IP του τέλους λήψης |
Επιστρεφόμενη αξία | Παράδειγμα: ATGIP_ ATGIP192.168.0.215 ΟΚ |
Παρατήρηση | εντολή ερωτήματος |
OSD Overlay Protocol
Μορφή | ATOSD$(idx), $(Χ), $(y), $(str)_ Παράδειγμα:ATOSD0,40,20,height: 100m_ |
παράμετρος | 1. IDX index: 0~7 (supports OSD overlay for 8 areas) 2. X-coordinate: 0~1919 3. Y coordinate: 0~1079 4. str: the string to be displayed at the corresponding coordinates (the space symbol is used to clear the display) |
Χρήση | on the video screen.OSD information |
Επιστρεφόμενη αξία | Οχι |
Παρατηρήσεις | 1. The user specifies the x and y coordinates of the OSD display according to the maximum 1920×1080 pixels, and the system will correct the coordinates according to the actual display situation. 2. The ‘_’ character cannot be contained in the str parameter |
Set Gain To Adjust
Μορφή | ATSAD$(συχν),$(adjust) _ Παράδειγμα:ATSAD700000,2.5_ |
παράμετρος | wireless central working frequency: Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) Adjust the value(dB): ATSD cmd will subtract this value to set the wireless gain |
Λειτουργία | Specify and adjust the value for the wireless gain setting using by ATSD cmd |
Ανατροφοδότηση | Παράδειγμα: ATSAD700000,2.5_ freq:700000,adjust:2.50 Εντάξει |
Σχόλια | Setting command is still valid when stopping power or resetting. |
Get Gain To Adjust
Μορφή | ATGAD[$(συχν)]_ Παράδειγμα:ATGAD700000_ |
παράμετρος | wireless central working frequency: Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) When no parameter provides, it will list all the freq that have adjusted value. |
Λειτουργία | Inquiry adjust the value for wireless gain setting using ATSD cmd |
Ανατροφοδότηση | Παράδειγμα: ATGAD700000_ freq:700000,adjust:2.50 OK ATGAD_ freq:700000 750000 Εντάξει |
Σχόλια | Inquiry command. |
Serial Port Utility software download
https://www.alithon.com/downloads
Συχνές Ερωτήσεις
1. How can I return to the No Password setting with 000000 indications after the change?
Reset the password to 000000 (one must not be missing) through the Parameter Configuration Panel Board.
or set it through ο ATSP_command
2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (Κέρδος) good for linear output operation? Or do you suggest some limited range for better linear operation?
The Gain of the COFDM configuration is the internal Gain, not the actual output power of the transmitter. The internal gain range is 0~89.75dB and the linear output:
1. At around 300~500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -5dBm.
2. At around 1000~1500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -6dBm to -10dBm.
3. I tried to set – B bandwidth (kHz) and E bit rate (Mbps). When I set E, the new value does not apply. So. the E setting is only for monitoring of available bitrate? if I wish to change the E (Νιτρικά) I have to change only B (εύρος ζώνης)? Am I right?
It is not recommended to modify the video bit rate ‘E’ directly, because if the output video bit rate is greater than the wireless air interface rate, the system will not work normally.
Από προεπιλογή, the internal video bit rate ‘E’ will be set to 0 for automatic. Customers only need to modify ‘B’ to modify the wireless parameters, and the video bit rate will automatically adapt.
You can also adjust the wireless air interface rate by modifying GI and CR.
For more details on the Encoder Modulator Decoder Demodulator Module, please send an inquiry to us.
COFDM Modulator Demodulator Module Encoder Αποκωδικοποιητής HDMI CVBS AV Είσοδος AES 256 Ροή FHD RF
Κριτικές
Δεν υπάρχουν σχόλια ακόμη.