Imodyuli yokuhambisa ividiyo yeVTX ende

Without an extra Power Amplifier, our long-range VTX Vcan1681 has 300mW PA inside, it supports 0~15km.
Plus 2-watt power amplifier, the transmission distance can reach 30km in the visual range. (our model is TX900)
Plus 5-watt power amplifier, the transmission distance can reach 80km.
Plus 10-watt power amplifier, the transmission distance can reach 150km.

Everything works okay, but the problem is that it looks like it has locked me out from accessing the air unit via the ground unit. When I try to access the air unit by its IP address, it brings up that login screen. When I connect via ethernet, it works fine, but through the ground unit, it asks to log in. Two days ago everything was fine.
Now I changed the side IP address and I can’t even ping it anymore, but the link is still okay, and I can access it directly.

Solution:
Please clear your browser’s cookie information and visit again and it should solve the problem.
You should have used our devices with multiple versions of firmware. kunjalo, with the same IP address, the browser cached the cookies of different versions of the firmware, resulting in a confusing display. Clearing the cookies of the browser and visiting again should solve the problem. No need to restore the factory settings of our equipment, as you said.

Why I am asking, I had Raspberry PI connected to the Ethernet1 port and streaming video. Now I have the same unit connected to the Ethernet2 port, and I got nothing. I can see activity on that port but no video goes through on the other side. I can’t even ping it video the Ethernet2. Are they bridged?

Phendula: The ethernet1 and the ethernet 2 are the two ports of the switch chip inside.

The two network ports of Vcan1681 and TX900 bridge internally. They are equivalent to the network ports of a network switch.

You need to check whether there is any problem with the 4PIN network port connection cable and whether there is any IP address conflict in the LAN (including our 1618 device). Each of our 1618s takes up two IP addresses.

If you have not modified the IP address at the time of shipment, the default is 192.168.1.12 kwaye 192.168.168.12, and the docked 1681 defaults to 192.168.1.11 kwaye 192.168.168.11

Verification is also very simple. Connect eth1 and eth2 of the 1681 module to two PCs’ namazibuko, and check if the PCs can communicate normally by pinging each other.)

Maybe the RJ45 cable and the ethernet 2 do not closely contact the ethernet 2.

The 192.168.168.x network segment is Modem’s IP.
The 192.168.1.x network segment is the IP of the MCU.

Ewe.
There are two RJ45 ethernet interfaces for video or internet data, one set of audio interfaces, and three sets of data interfaces. If you transmit data, the data interface can be used rs232, TTL, sbus, etc. It can be modified according to your needs.

Just use your own software.
We are equivalent to providing a wireless network, Connect two computers or network devices.

Ewe, max Support 7 ~ 8 relays at one line.
iinkcukacha ezithe xaxe, https://ivcan.com/drone-repeater-solution/

I want to explain the working scenario of the long-range VTX.

Two drones will be in the air with HD cameras and one modem will be on the ground connected to the display.

The transceiver modem in the air will send videos from the air to the ground + olunye ulwazi oluluncedo ngakumbi. Baya kufumana kwakhona ulawulo lwekhamera kunye nemiyalelo ye-PTT evela emhlabeni.

Another transceiver modem on the ground will receive videos from the air and will display them on some LCD or send them on ethernet. Iya kuthumela kwakhona ulawulo lwekhamera + I-PTT iyalela iidrones emoyeni.

800MHz, 1.4G, kunye ne-2.4G.

Ewe, inkxaso.

Ewe