How to test COFDM IP wireless video data transmitter module

How to test the one-way network transparent transmission module?

There are two steps here, the first step is to connect the wireless transmission module to the computer with a network cable, and the second step is to run the network assistant on the computer and configure it correctly.

After configuring the network assistant, send the data string on the computer connected to the transmitting module, and observe whether the network assistant on the computer connected to the receiving module can receive the correct data string.

First of all, you will find that both the transmitter module and the receiver module have a network port. We connect the transmitter module and the receiver module to two computers through network cables.

Please note that both computers must be set on the same network segment, such as 192.168.1.xxx.

Then run the network assistant on the computer and configure it correctly. This step is very critical.

1. Find two PCs, configure static IP addresses, and ensure that the two PCs are in the same network segment (misol uchun, 192.168.0.90 va 192.168.0.215).
2. Two PCs are respectively connected to the sending end and receiving end of the cofdm one-way transparent transmission link (misol uchun, the PC IP connected to the transmitting end is 192.168.0.90, and the PC IP connected to the receiving end is 192.168.0.215)
3. Run the “NetAssist V5.0.8” dasturiy ta'minot on the PC connected to the transmitter, and configure it as UDP sending mode (broadcast, destination port: 8090), Quyida ko'rsatilganidek:

4. On the PC connected to the receiving end, run the “NetAssist” software and configure it as UDP receiving mode (Local port: 8090), Quyida ko'rsatilganidek:

5. The PC connected to the transmitting end sends data, and in the case of a wireless link connection, the PC connected to the receiving end will receive the data sent by the PC at the transmitting end.

Here are some suggestions.

1. For transmitter settings, the target port is not recommended to be the same as the local port, misol uchun, you can set the target port to 8090.
2. 
3. The ip of the receiver should be the same as that of the transmitter. Masalan, if the transmitter is 192.168.1.x, the receiver must also be 192.168.1.x.
4. The local port of the receiver must be consistent with the target port of the transmitter, misol uchun, both are set to 8090.
5. The principle is essential that two PCs communicate with UDP broadcast under the same ip network segment, set them to configure the same IP network segment, and then the target port of the transmitter must be consistent with the local port of the receiver.
6. The most critical one is that because it is a one-way link, it needs to use UDP broadcast/multicast (not even on-demand), so the target IP of the PC on the transmitter side should be set to broadcast ip, kabi 192.168.1.255
7. The green light on the receiving end is flashing, indicating that the wireless link is connected.
8. If the configuration is correct, the network assistant of the computer where the receiver is located still does not display received data, it may be a firewall problem.
9. It is also possible that multiple network debugging assistants have been opened before, please check the computer to ensure that only one network assistant program is running.
10. If UDP broadcasts to transmit video data, the firewall must be closed, and it is not clear to transmit such small data. It is best to suggest turning off the firewall or adding Network Assistant to the allowed applications of the firewall.
11. There is a drop-down menu in the upper left corner, you can choose languages-English.
12. Please ping the transmitter and receiver IPs on the PCs on both sides to confirm that the physical connection of the network card is good: Connect the pc of the transmitter, ping the transmitter Ip: 192.168.1.30; Connect the pc of the receiver, ping the receiver Ip: 192.168.1.24
13. Make sure your received pc has only one net-assist running.
14. Please disconnect and then connect for the check, or you can quickly net-assist and then reopen for the test.

In this video, Men sizga bir tomonlama tarmoqning shaffof uzatish modulini sinab ko'rishdan oldin kompyuterda tarmoq yordamchisini qanday to'g'ri sozlashni tanishtirdim..

Yuqoridagi sinov yechimi quyidagi model uchun.

1. Barcha sozlamalar sizning talablaringizga muvofiq sozlangan, lekin ma'lumotlarni hali ham uzatish mumkin emas, nima qilishim kerak?

1. Birinchidan, yuklab oling va o'rnating Wireshark ikkita kompyuterda, va tekshiring.
2. 
3. UDP packet is transparent transmission, so you can see the same UDP packet(misol uchun, source: 192.168.1.40, destination: 192.168.1.255, port: 8090) on both sides pc using Wireshark.
4. Wireshark on receive pc has found the UDP packet from tx, just the problem of net-assist on the receiver PC.

2. Nima uchun Parametr konfiguratsiyasi paneli vositasida ikki xil chastotani ko'raman, men ushbu bir tomonlama tarmoq simsiz shaffof uzatish moduliga ulanganimda?

This board has two uses. The default shipment is used as a relay, so there will be Tx and Rx parameters. For your customers to use it as a one-way network transparent transmission transmitter, just pay attention to the parameters on the Tx page.

It is recommended that you first test according to the above video we listed, and do not modify the parameters.

3. Bir tomonlama videoni translyatsiya manzili sifatida uzatish uchun yaxshi ishlaydi 192.168.1.255, Lekin biz 239.1.1.1 kabi multicast hovuz bilan ishlashimiz kerak…. Hozir, multicast ishlamaydi, tx va rx multicast trafikdan o'tishi kerak, Iltimos, ushbu muammoni hal qilish uchun yangilangan proshivkani yuboring.

Please upgrade the below firmware. (how to upgrade the firmware?)

https://drive.google.com/file/d/1SD495jVMeRH1zUUbQkWk_9PnZ90o9ba4/view?usp=drive_link