என்கோடர் மாடுலேட்டர் டிகோடர் டிமோடுலேட்டர் தொகுதி அளவுரு உள்ளமைவு வழிமுறைகள் COFDM AT கட்டளை
![என்கோடர் மாடுலேட்டர் டிகோடர் டிமோடுலேட்டர் தொகுதி அளவுரு உள்ளமைவு வழிமுறைகள் COFDM AT கட்டளை�லேட்டர் தொகுதி Parameter Configuration Instructions COFDM AT Command 44 Encoder Modulator Decoder Demodulator Module](https://i0.wp.com/ivcan.com/wp-content/uploads/2023/01/COFDM-RF-demodulator-decoder-receiver-H264-Vcan1776RX-H264.webp?resize=1000%2C1000&ssl=1)
Download the Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions below if you need a PDF file.
Update Record:
பதிப்பு | தேதி | விளக்கம் |
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 | 2016-10-24 2016-11-1 2016-12-26 2017-2-14 2017-2-28 2017-3-27 2017-4-19 2017-5-18 2017-9-12 2018-3-15 2019-6-25 2023-2-24 | Initial version ATDR reply distinguishing module ATSE, ATGE add audio switch Add ATSP protocol Add ATST, ATGT protocol ATGE command add AESfor status acquisition Added ATGB protocol AV and HDMI output control Support for obtaining the current AV output standard Added ATSU, ATGUcommands Added ATOSD, ATSIP, ATGIP commands Added ATSAD, ATGAD commands |
Users may need to modify the configuration parameters of the module during the use of the COFDM modulator and demodulator module. In order to simplify the user’s operation, we design the parameter configuration into a few simple AT commands. The user only needs to use the specified AT command and pass the corresponding parameters to complete the parameter setting of the COFDM module.
Suitable Models
Command Introduction
The AT command for configuring COFDM module parameters starts with “AT” and ends with an underscore “_”. Each AT command has several or no parameters, and each AT command has a return value. For details, please refer to the introduction of the following commands.
Users can configure the parameters of the module through the configuration serial port (இந்த TTL நிலை, 3.3வி) of the COFDM module. For detailed serial port configuration, refer to the figure below. Please use tools such as “Serial Port Debugging Assistant” to send AT commands to the COFDM module, pay attention to the use of உரை, உதாரணத்திற்கு:
![என்கோடர் மாடுலேட்டர் டிகோடர் டிமோடுலேட்டர் தொகுதி அளவுரு உள்ளமைவு வழிமுறைகள் COFDM AT கட்டளை 49 Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions COFDM AT Command 1](https://i0.wp.com/ivcan.com/wp-content/uploads/2022/11/serial-debug-assitant_iVcan.webp?resize=800%2C585&ssl=1)
சிommand Classification
The AT commands for configuring COFDM module parameters are mainly divided into the following two categories:
Query Commands | ஏடிடிஆர், ஏடிஜிடி, ATGE, ATGI , ஏடிஜிஆர், ATGT, ATGB, ATGU, ATGIP |
Setting Commands | ஏடிஎஸ்டி, ஏடிஎஸ்ஜி, ஏடிஎஸ்எம், ATSE, ATSI, ATSO, ஏடிஎஸ்ஆர், ATSP, ATST, ATSU,ATOSD, ATSIP |
From the perspective of whether to save after power-off, the setting commands can be divided into:
Power-off Saving Commands | ஏடிஎஸ்டி, ATSE, ATSI, ATSO, ஏடிஎஸ்ஆர், ATSP, ATST, ATSU, ATSIP |
Power-off Not Saving Commands | ஏடிஎஸ்ஜி, ஏடிஎஸ்எம், ATOSD |
According to the configuration transmitter or receiver, the classification is as follows:
Sender Configuration Commands | ஏடிடிஆர், ஏடிஎஸ்டி, ஏடிஜிடி, ஏடிஎஸ்ஜி, ஏடிஎஸ்எம், ATSE, ATGE, ATSI, ATGI, ATSO, ATSP, ATST, ATGT, ATSU, ATGU, ATOSD |
Receiver Configuration Commands | ஏடிடிஆர், ஏடிஎஸ்ஆர், ஏடிஜிஆர், ATSP, ATST, ATGT, ATGB, ATSIP, ATGIP |
Command Details
Ping Command
வடிவம் | ATDR_ |
அளவுரு | இல்லை |
பயன்பாட்டு | for the integrated system to check whether the serial port is connected and identify the connected modules. |
Return value | RCB returns the “device profile” string SUE1 returns “ATDRSUE1 OK” string SHD1 returns “ATDRSHD1 OK” string |
கருத்து | query command |
Set Device Command
வடிவம் | ஏடிஎஸ்டி $(mimo), $(gi), $(COFDM வயர்லெஸ் டிரான்ஸ்மிஷன் சிஸ்டம் டிரான்ஸ்மிஷன் ரேட் கணக்கீடு), $ (விண்மீன் கூட்டம்), $(அதிர்வெண்(KHz வேண்டும்)), $(bw(KHz வேண்டும்)), $(tx1_gain), $(tx2_gain)_ Example: ATSD0,1,0,0,800000,8000,86.0,86.0_ |
அளவுரு | One Antenna/Dual antenna mimo: 0 mimo disable; 1 mimo enable Guard Interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1/4 Convolution Code Rate: 0 1/2; 1 2 /3; 2 3/4; 3 5/6; 4 7/8; விண்மீன்: 0 க்யுபிஎஸ்கே; 1 QAM16; 2 QAM64; RCB Carrier Center Frequency(கிலோஹெர்ட்ஸ்) 200000~2700000(200MHz~2.7GHz, 1KHz படி) RC900 Carrier center Frequency(கிலோஹெர்ட்ஸ்) 750000~930000(750மெகா ஹெர்ட்ஸ் ~ 930MHz, 1KHz படி) RCB Channel bandwidth bw(KHz வேண்டும்) 2000~8000(2MHz~8MHz, 1KHz படி) RCB Channel bandwidth bw(KHz வேண்டும்) 2000~8000 (2MHz~8MHz, 1KHz படி) Transmitting antenna 1 gain tx1_gain 0.0~89.75dB, 0.25dB படி Transmitting antenna 2 gain tx2_gain 0.0~89.75dB, 0.25dB படி |
Return Value | போன்ற:ATSD0,1,0,0,800000,8000,86.0,86.0_ SISO,ஜி.ஐ.: 1/16, CR:1/2, MOD: க்யுபிஎஸ்கே, அதிர்வெண்:800000KHz வேண்டும்,bw:8000KHz வேண்டும்,tx1_gain:86.000000 tx2_gain:86.000000 சரி |
குறிப்பு | Set command, save when power off. Different Bandwidths, காவலர் இடைவெளியில், Convolution code rates, Data rate calculation formulas corresponding to constellations Air interface rate Rate(COFDM வயர்லெஸ் டிரான்ஸ்மிஷன் சிஸ்டம் டிரான்ஸ்மிஷன் ரேட் கணக்கீடு) COFDM வயர்லெஸ் டிரான்ஸ்மிஷன் சிஸ்டம் டிரான்ஸ்மிஷன் ரேட் கணக்கீடு (அலைவரிசையை(மெகா ஹெர்ட்ஸ்) * 8.0/7.0) / (1+ஜி.ஐ.) * 1512/2048*COFDM வயர்லெஸ் டிரான்ஸ்மிஷன் சிஸ்டம் டிரான்ஸ்மிஷன் ரேட் கணக்கீடு(COFDM வயர்லெஸ் டிரான்ஸ்மிஷன் சிஸ்டம் டிரான்ஸ்மிஷன் ரேட் கணக்கீடு) * COFDM வயர்லெஸ் டிரான்ஸ்மிஷன் சிஸ்டம் டிரான்ஸ்மிஷன் ரேட் கணக்கீடு * 188/204. Taking 8MHz bandwidth as an example, different guard intervals, convolution code rates, data rates corresponding to constellations and required receiving signal-to-noise ratios |
எஸ்et Gain Command
வடிவம் | ATSG$( tx1_gain),$( tx1_gain)_ Example: ATSG85.0,85.0_ |
அளவுரு | tx1_gain: அனுப்பும் 1 ஆதாயம் tx2_gain: அனுப்பும் 2 ஆதாயம் |
பயன்பாட்டு | To dynamically adjust the output power. If the signal SNR/RSSI of the receiver is high, the output power can be reduced through the remote control link. When the SNR/RSSI of the end signal is low, increase the output power (டிரான்ஸ்மிட்டர்) |
Return Value, | Example: ATSG85.0,85.0_set gain 85.000000 85.000000 சரி |
கருத்து | setting command, power off will not save. |
Set Modulation Mode commanஈ
வடிவம் | ATSM$(gi), $(COFDM வயர்லெஸ் டிரான்ஸ்மிஷன் சிஸ்டம் டிரான்ஸ்மிஷன் ரேட் கணக்கீடு), $(விண்மீன் கூட்டம்)_ Example: ATSM1,1,2_ |
அளவுரு | Gard interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1 /4; Convolution code rate: 0 1/2; 1 2/3; 2 3/4; 3 5/6; 4 7/8; விண்மீன்: 0 க்யுபிஎஸ்கே; 1 QAM16; 2 QAM64 |
பயன்பாட்டு | Dynamically adjust the air interface rate, the air interface rate can be increased when the distance is short, and the air interface rate can be reduced when the distance is long (டிரான்ஸ்மிட்டர்) |
Return Value | Example:ATSM1,1,2_GI:1/16, CR:2/3, MOD: QAM64, சரி |
கருத்து | setting command, power off will not save. |
ஜிet Device Status Command
வடிவம் | ATGD_ |
அளவுரு | இல்லை |
பயன்பாட்டு | query the current number of transmit antennas, பாதுகாப்பு இடைவெளி, convolution code rate, number of constellations, transmit frequency, அலைவரிசையை, gain parameters (டிரான்ஸ்மிட்டர்) |
Return Value | Example: ATGD_ SISO, ஜி.ஐ.:1 /16, CR: 1/2, MOD: க்யுபிஎஸ்கே, அதிர்வெண்: 800000KHz வேண்டும், bw: 8000KHz வேண்டும், tx1_gain: 86.000000 tx2_gain: 86.000000 சரி |
கருத்து | query command |
Set Encoder Command
வடிவம் | ATSE$(llc),$(rt),$(bitrate) ,$(gop),$(ஆடியோ)_ Example: ATSE0,0,0.0,0,0_ |
அளவுரு | 1. Enhanced data reliability option llc: 0 disable; 1 enable (requires the receiving end to enable this option at the same time, use in pairs, because more redundant data is added to enhance reliability, the video bit rate of the transmitting end should be set when this option is turned off half of) 2. Real-time priority/quality priority rt: 0 image quality priority; 1 real-time priority; 3. பிட்ரேட்: 0 let system decide; >0 specify bitrate(float) 4. I frame interval GOP: 0 let system decide; >0 specify GOP 5. Audio encoding option audio: 0 disable; 1 enable |
பயன்பாட்டு | Used to set encoding parameters (அனுப்பும்) |
Return Value | Example:ATSE0, 0,0.0,0,0_ முறை:0,RT:0,bitrate: 0.0நொடி,gop:0,ஆடியோ:0,சரி |
கருத்து | setting command, save when power is off. |
Get Encoder Command
வடிவம் | ATGE_ |
அளவுரு | இல்லை |
பயன்பாட்டு | querying encoding parameters (sending end) |
Return Value | Example:ATGE_MODE:0, RT:0,bitrate:4.0நொடி,gop:10,ஆடியோ:0,aes:0, சரி |
கருத்து | Query command AES means the current encryption status: 0 disable; 1 enable |
Get Input Command
வடிவம் | ATGI_ |
அளவுரு | இல்லை |
பயன்பாட்டு | query the current camera input parameters (டிரான்ஸ்மிட்டர்) |
Return Value | Example:ATGI_input_size: 1080ப, input_rate: 60அசாதாரணமான, sensor_type: hdmi,சரி |
கருத்து | query command |
Set Input Command
வடிவம் | ATSI$(input_size),$(input_rate)_ Example: ATSI1080,25_ |
அளவுரு | 1. Input resolution input_size: 0 let the system detect; >0 specify input size 2. Input frame rate input_rate: 0 let the system detect; > 0 specify input fps |
பயன்பாட்டு | To specify the input resolution and frame rate to meet some special signal sources, or some special application needs (டிரான்ஸ்மிட்டர்) |
Return Value | Example: ATSI1080,25_ Input_size:1080ப,input_rate: 25அசாதாரணமான, சரி |
குறிப்புகள் | After the user specifies the input resolution and frame rate through this command, the system will no longer detect the signal source (use with caution). The user can restore the default through the following command: ATSI0,0_Set the command and save it after power-off. |
Set Output Command
வடிவம் | ATSO$(output_size),$(output_rate)_ Example: ATSO720,30_ |
அளவுரு | 1. அனுப்பும்: encoding output resolution output_size: 0 equal to input_size; >0 specify output size 2. பெறுநர்: HDMI output resolution (720, 1080) 3. அனுப்பும்: encoding output frame rate output_rate: 0 equal to input_rate; >0 specify output_rate (அசாதாரணமான) 4. பெறுநர்: HDMI output frame rate 720p supports frame rate (50, 60); 1080p supports frame rate (24, 25, 30, 50, 60) |
பயன்பாட்டு | 1. அனுப்பும்: Used to specify the encoding output resolution and frame rate to meet the requirements of certain applications for zooming and frame reduction 2. பெறுநர்: used to configure the resolution and frame rate of HDMI output |
Return Value | Example: ATSO720,30_ output_size: 720ப, output_rate: 30அசாதாரணமான, சரி |
குறிப்புகள் | 1. For HDMI input only, this command is invalid for AV input 2. Output_size <= input_size; output_rate<=input_rate 3. Set the command and save it after the power is off. |
Set Input Sources Command (switch HDMI / Cvbs உள்ளீடு)
வடிவம் | ATSU$(vin),$(ain)_ Example: ATSU0,1 _ |
அளவுரு | 1. Video input selection VIN: 0 let the system detect; 1 force CVBS input; 2 force hdmi/SDI input 2. Audio input selection AIN: 0 let the system detect; 1 force analog input |
பயன்பாட்டு | Used to meet specific application requirements (Example: HDMI/SDI input video, MIC input audio) |
Return Value | Example: ATSU0,1_ ATSU0,1 OK |
கருத்து | setting command, power-off save. |
Get User Command
வடிவம் | ATGU _ Example: ATGU_ |
அளவுரு | இல்லை |
பயன்பாட்டு | To query user-specific configuration |
Return Value | Example: ATGU_ ATGU0,1 OK |
கருத்து | query command return parameter description please refer to the ATSU command |
Set Receiver Command
வடிவம் | ஏடிஎஸ்ஆர் $(அதிர்வெண்), $(bw ), $(llc), $(cvbs)_ Example: ATSR320000,6000,0,0_ |
அளவுரு | 1. DR2C carrier frequency freq(KHz வேண்டும்) 200000~860000(200மெகா ஹெர்ட்ஸ் ~ 860MHz, 1KHz படி) 2. DR900 carrier center frequency freq(KHz வேண்டும்) 200000~1600000(200MHz~1.6GHz, 1KHz படி) 3. DR2C channel bandwidth bw(KHz வேண்டும்) 2000~8000(2MHz~8MHz, 1KHz படி) 4. DR900 channel bandwidth bw(KHz வேண்டும்) 3200~8000(3.2MHz~8MHz, 1KHz படி) 5. Enhanced data reliability option llc: 0 disable; 1 enable (it is required that the transmitter should also enable this option at the same time, and use it in pairs. Since more redundant data is added to enhance reliability, the video bit rate of the transmitter should be set to when this option is turned off half of) 6. AV output system cvbs: 0 pal; 1 ntsc |
பயன்பாட்டு | To set the receiver parameter |
Return Value | உதாரணமாக: ATSR320000,6000,0,0_ ATSR320000,6000,0,0 OK |
கருத்து | setting command, save when power is off. |
Get Receiver Command
வடிவம் | ATGR_ |
அளவுரு | இல்லை |
ATGR_ | the receiving end parameter |
Return Value | Example: ATGR_ ATGR320000,6000,0,aes:0,cvbs:0 சரி |
கருத்து | 1. Query command 2. Aes parameter indicates the current encryption status: 0 disable;1 enable 3. CVBS parameter Indicates the current AV output standard: 0 pal;1 ntsc |
Get Bit Error Rate Command
வடிவம் | ATGB_ |
அளவுரு | இல்லை |
பயன்பாட்டு | querying the bit error rate and signal strength of the dual antennas at the receiving end |
Return Value | Example: ATGB_ ATGB ber1:0.00% ber2:0.00% RSSI1 :54 RSSI2:53 Lock1:1 Lock2:1 சரி |
குறிப்புகள் | 1. Query commands 2. Ber1 and ber2 respectively indicate the bit error rate of each antenna, ranging from 0.0% க்கு 100.0% 3. RSSI1 and RSSI2 respectively indicate the signal strength of each antenna, ranging from 0 க்கு 100 4. Lock1 and Lock2 respectively indicate the signal locking status of each antenna (1 Represents signal lock) |
Set Password Command
வடிவம் | ATSP$(password), $(password)_ Example: ATSP123456, 123456_ |
அளவுரு | AES key password: 6-digit password (ASCII) AES key password: 6-digit password (ASCII) (repeat it for confirmation) |
பயன்பாட்டு | Used to set the AES key of the transceiver (டிரான்ஸ்மிட்டர் மற்றும் ரிசீவர்) |
Return Value | Example: ATSP123456_ ATSP123456 OK |
கருத்து | 1. When the password is all 0, AES encryption is turned off. 2. Set the command and save it after powering it off. |
Set Data Transfer Command
வடிவம் | ATST$(பாட் விகிதம்), $( parity)_ Example: ATST115200,0_ |
அளவுரு | 1. Baud rate baud rate: 1200、2400、4800、9600、19200、38400、57600、115200 2. Check Code: 0: எதுவுமில்லை; 1: Odd; 2: Even |
பயன்பாட்டு | Used to set the baud rate and parity bit of the serial port for data transparent transmission |
Return Value | Example: ATST115200,0_ ATST115200,0 OK |
குறிப்புகள் | Set command |
Get Data Transfer Command
வடிவம் | ATGT_ |
அளவுரு | இல்லை |
பயன்பாட்டு | Used to query the baud rate and check code |
Return Value | Example: ATGT_ ATGT115200,0 OK |
குறிப்புகள் | Query command |
Set IP Address Command
வடிவம் | ATSIP$(ip), $(ip)_ Example: ATSIP192.168.1.215,192.168.1.215_ |
அளவுருக்கள் | Local IP address Local IP address (repeat to confirm) |
பயன்பாட்டு | Used to set the receiver IP address |
Return Value | Example: ATSIP_192.168.1 .215,192.168.1.215_ ATSIP192.168.1.215 OK |
குறிப்புகள் | 1. After setting the IP address, the receiving end needs to be restarted to take effect. 2. Set the command and save it after powering it off. |
Get IP Address Command
வடிவம் | ATGIP_ Example: ATGIP_ |
அளவுரு | இல்லை |
பயன்பாட்டு | to query the current IP address of the receiving end |
Return value | Example: ATGIP_ ATGIP192.168.0.215 OK |
கருத்து | query command |
OSD Overlay Protocol
வடிவம் | ATOSD$(idx), $(எக்ஸ்), $(ஒய்), $(str)_ Example:ATOSD0,40,20,height: 100மீ_ |
அளவுரு | 1. IDX index: 0~7 (supports OSD overlay for 8 areas) 2. X-coordinate: 0~1919 3. Y coordinate: 0~1079 4. str: the string to be displayed at the corresponding coordinates (the space symbol is used to clear the display) |
பயன்பாட்டு | on the video screen.OSD information |
Return value | இல்லை |
குறிப்புகள் | 1. The user specifies the x and y coordinates of the OSD display according to the maximum 1920×1080 பிக்சல்கள், and the system will correct the coordinates according to the actual display situation. 2. The ‘_’ character cannot be contained in the str parameter |
Set Gain To Adjust
வடிவம் | ATSAD$(அதிர்வெண்),$(adjust) _ Example:ATSAD700000,2.5_ |
அளவுரு | wireless central working frequency: அடிக்கடி(KHz வேண்டும்) 200000~2700000(200MHz~2.7GHz, step: 1KHz வேண்டும்) Adjust the value(டெசிபல்): ATSD cmd will subtract this value to set the wireless gain |
விழா | Specify and adjust the value for the wireless gain setting using by ATSD cmd |
பின்னூட்டம் | Example: ATSAD700000,2.5_ freq:700000,adjust:2.50 சரி |
கருத்துகள் | Setting command is still valid when stopping power or resetting. |
Get Gain To Adjust
வடிவம் | ATGAD[$(அதிர்வெண்)]_ Example:ATGAD700000_ |
அளவுரு | wireless central working frequency: அடிக்கடி(KHz வேண்டும்) 200000~2700000(200MHz~2.7GHz, step: 1KHz வேண்டும்) When no parameter provides, it will list all the freq that have adjusted value. |
விழா | Inquiry adjust the value for wireless gain setting using ATSD cmd |
பின்னூட்டம் | Example: ATGAD700000_ freq:700000,adjust:2.50 OK ATGAD_ freq:700000 750000 சரி |
கருத்துகள் | Inquiry command. |
Serial Port Utility software download
: https://www.alithon.com/downloads
கேள்விகள்
1. How can I return to the No Password setting with 000000 indications after the change?
Reset the password to 000000 (one must not be missing) through the Parameter Configuration Panel Board.
or set it through தி ATSP_command
2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (கெயின்) good for linear output operation? Or do you suggest some limited range for better linear operation?
The Gain of the COFDM configuration is the internal Gain, not the actual output power of the transmitter. The internal gain range is 0~89.75dB and the linear output:
1. At around 300~500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -5dBm.
2. At around 1000~1500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -6dBm to -10dBm.
3. I tried to set – B bandwidth (கிலோஹெர்ட்ஸ்) and E bit rate (நொடி). When I set E, the new value does not apply. So. the E setting is only for monitoring of available bitrate? if I wish to change the E (பிட்ரேட்) I have to change only B (அலைவரிசையை)? Am I right?
It is not recommended to modify the video bit rate ‘E’ directly, because if the output video bit rate is greater than the wireless air interface rate, the system will not work normally.
இயல்பாக, the internal video bit rate ‘E’ will be set to 0 for automatic. Customers only need to modify ‘B’ to modify the wireless parameters, and the video bit rate will automatically adapt.
You can also adjust the wireless air interface rate by modifying GI and CR.
For more details on the Encoder Modulator Decoder Demodulator Module, please send an inquiry to us.
COFDM மாடுலேட்டர் டெமோடுலேட்டர் மாட்யூல் என்கோடர் டிகோடர் HDMI CVBS AV உள்ளீடு AES 256 FHD RF ஸ்ட்ரீமிங்
$0.00
விமர்சனங்கள்
எந்த மதிப்பீடுகளும் இன்னும் உள்ளன.