2 Vatios wa 5 Vatios wa 10 watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter
Nuna gehna 'nar xe̲ni clave 'nar transmisor video inalámbrico, nä'ä to ntu̲ngi ar señal RF 'nar dätä ntsoni ngatho ne distancia. Opcional 1 Watt, 2 Watt, 5 Watt, ne 10 Watt.
Tabla contenidos
Características
- Me̲'bida frecuencia: 800Mhz — 830 Mhz, 1425MHz-1455MH
- RF jar: 25±2dBm
- Nts'edi salida RF: 2 Watt (33dBm)
- 1400Mhz Transmitter gains 11dB when used with 'nar módulo enlace datos vídeo inalámbrico bidireccional, configurar la potencia máxima de RF como 22 ~ 24 dBm, then the RF out power will be 33~35 dBm.
- 800Ganancia del transmisor Mhz: 13dB, when used with a two-way wireless video data link module, configurar la potencia máxima de RF como 20 ~ 22 dBm, then the RF out power will be 33~35 dBm.
- Nts'edi salida RF: 5 Watt (37dBm)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, configure la potencia máxima de RF como 22 ~ 25 dBm, then the RF out power will be 37~37 dBm.
- 800Ganancia del transmisor Mhz: 17dB, when used with a two-way wireless video data link module, configurar la potencia máxima de RF como 20 ~ 22 dBm, then the RF out power will be 37~39 dBm.
- Nts'edi salida RF: 10 Watt (40dBm)
- Ganancia TX: 18dB, when used with a two-way wireless video data link module, set up the maximum RF power of as 22~24 dBm, then the RF out power will be 40~42dbm.
- 2 Potencia de vatios en DC12V ~ 16V;
- 5 Watts Power in DC24V~25V, minimum 1.8A@24V power current rating
- 10 Watts Power in DC24V~30V, minimum 2.5A@28V power current rating
- 2 Vatios Consumo energía: <6W promedio; 5 Vatios Consumo energía: <14W promedio; 10 Vatios Consumo energía: <28W promedio
- 2 Vatios 5 Watts PCBA size: 46.5*31mm, ar grosor ar PCB: 1.2mm
- 10 Watts Dimensions: 65*62*13.5mm, not including the connector out of the metal housing, Be̲xu: 98g
- Impedancia: 50 Ohm
Mpe̲fi xkagentho junto ko 'nar módulo enlace datos vídeo inalámbrico bidireccional:
Entrada RF
Salida RF
Nts'edi ja | We should solder two bonding pads to connect with power VDD and GND. |
Control | We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL ne GND). Ar entrada mextha (1.8V 3.3V) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode. |
RF jar | Conector IPEX pa conexión ko ar antena principal módulo enlace datos vídeo inalámbrico bidireccional. |
Salida de RF | We should solder the bonding pad to an antenna connector. |
Carcasa ne montaje
Xtí modelo pe̲ts'i 'nar amplificador ar nts'edi incorporado ar interior.
Ya nt'a̲ni mäs frecuentes:
Q: Could you tell me your RF power amplifier dimension size? I want to design my enclosure.
MA: Jaki ar mäte, consulte ar tsita ar abajo. And tell us if you need any further information.
Q: Could you show me the real photos of your RF linear power amplifier?
MA: sure, please check the below pictures.
Q: Are you not using the TQP7M9104 amplifier in the 2W module?
MA: Hi'nä