2 Watts an 5 Watts an 10 watts PA Linear Power Amplifier RF panela module PCBA ji bo veguhezkarê girêdana daneya vîdyoya bêtêl

2 Watts PA Linear Power Amplifier RF module board PCBA for wireless video data link transmitter — 2 Watts PA Linear Power Amplifier RF module PCBA ji bo veguhezkarê girêdana daneya vîdyoyê ya bêtêl

Ev beşek sereke ya veguhestina vîdyoya wireless ye, ku dikare sînyala RF-ê ji bo rêgez û dûrtir mezin bike. Bixwe 1 watt, 2 watt, 5 watt, û 10 watt.

Tabloya naverokê

Dengûbas

Koma frekansê: 800Mhz-830Mhz, 1425MHz-1455MH
RF di: 252dBm ±
RF ji hêza: 2 watt (33DBM)
- 1400Mhz Transmitter gains 11dB when used with modulek girêdana daneya vîdyoyê ya du-alî ya bêhêl, hêza RF ya herî zêde wekî 22~24 dBm saz bikin, then the RF out power will be 33~35 dBm.
- 800Qezenckirina Mhz Transmitter: 13dB, when used with a two-way wireless video data link module, hêza RF ya herî zêde wekî 20~22 dBm saz bikin, then the RF out power will be 33~35 dBm.
RF ji hêza: 5 watt (37DBM)
- 1400Mhz Transmitter gains 15dB when used with a two-way wireless video data link module, hêza RF ya herî zêde wekî 22 ~ 25 dBm saz bikin, then the RF out power will be 37~37 dBm.
- 800Qezenckirina Mhz Transmitter: 17dB, when used with a two-way wireless video data link module, hêza RF ya herî zêde wekî 20~22 dBm saz bikin, then the RF out power will be 37~39 dBm.
RF ji hêza: 10 watt (40DBM)
- qezenc TX: 18dB, when used with a two-way wireless video data link module, hêza RF ya herî zêde ya 22 ~ 24 dBm saz bikin, wê hingê hêza RF-ê dê bibe 40~42dbm.
2 Hêza Watts di DC12V ~ 16V de;
5 Hêza Watts di DC24V ~ 25V de, herî kêm 1.8A@24V rêjeya niha hêza
10 Hêza Watts di DC24V ~ 30V de, herî kêm 2.5A@28V rêjeya niha hêza
2 Mezaxtina Hêzê ya Watts: <6W navoser; 5 Mezaxtina Hêzê ya Watts: <14W navoser; 10 Mezaxtina Hêzê ya Watts: <28W navîn
2 Watts 5 Mezinahiya PCBA Watts: 46.5*31mm, qalindahiya PCB: 1.2mm
10 Mezinahiyên Watts: 65*62*13.5mm, ne di nav de connector ji xanîyê metal, Pîvan: 98g
impedance: 50 Ohm

Bi hev re dixebitin Modula girêdana daneya vîdyoyê ya du-alî ya bêhêl:

How to connect the PA power amplifier with the two way wireless video data link module — Meriv çawa amplifikatora hêza PA-yê bi modula girêdana daneya vîdyoyê ya du-alî ve girêdide

RF Input

Derketina RF

2 Watts PA Linear Power Amplifier RF module board PCBA RF output — 2 Watts PA Linear Power Amplifier RF module board PCBA RF encam

Hêza nav	We should solder two bonding pads to connect with power VDD and GND.
Kontrol	We should solder two bonding pads to connect with a two-way wireless video data link module Switch signal pad(SCL û GND). Input bilind (1.8V heta 3.3V) will drive the amplifier and work in transmitter mode. The input low will enable the PA module to work in receiver mode.
RF di	Têkila IPEX-ê ji bo girêdana bi antenna sereke ya modula girêdana daneya vîdyoyê ya du-alî ya bêhêl.
RF derket	We should solder the bonding pad to an antenna connector.

Doza xanî û kombûnê

We recommend that this power amplifier for our two-way wireless video data link OEM PCBA module.

To enhance the power amplifier in conjunction with our two-way wireless video data link module, we recommend you fabricate a metallic housing casing that aligns with your device’s architecture.

It should also leave at least 6mm between the PA board and the upper cover. In order to facilitate heat dissipation and establish an electrical grounding connection, the back side of the PA board must be directly and firmly attached to the metal.

Proper integration of heat dissipation techniques, such as a heat sink or fan, is essential for optimal performance in designs utilizing the PA OEM module.

Em dikarin li gorî hewcedariya xerîdar ji bo vê modula PA-yê jî jûreyek metal çêbikin.

Modela jêrîn di hundurê de Amplifikatorek Hêzê ya çêkirî heye.