ಎನ್ಕೋಡರ್ ಮಾಡ್ಯುಲೇಟರ್ ಡಿಕೋಡರ್ ಡಿಮೋಡ್ಯುಲೇಟರ್ ಮಾಡ್ಯೂಲ್ ಪ್ಯಾರಾಮೀಟರ್ ಕಾನ್ಫಿಗರೇಶನ್ ಸೂಚನೆಗಳು COFDM AT ಕಮಾಂಡ್
Download the Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions below if you need a PDF file.
Update Record:
ಆವೃತ್ತಿ | ದಿನಾಂಕ | ವಿವರಣೆ |
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 | 2016-10-24 2016-11-1 2016-12-26 2017-2-14 2017-2-28 2017-3-27 2017-4-19 2017-5-18 2017-9-12 2018-3-15 2019-6-25 2023-2-24 | Initial version ATDR reply distinguishing module ATSE, ATGE add audio switch Add ATSP protocol Add ATST, ATGT protocol ATGE command add AESfor status acquisition Added ATGB protocol AV and HDMI output control Support for obtaining the current AV output standard Added ATSU, ATGUcommands Added ATOSD, ATSIP, ATGIP commands Added ATSAD, ATGAD commands |
Users may need to modify the configuration parameters of the module during the use of the COFDM modulator and demodulator module. In order to simplify the user’s operation, we design the parameter configuration into a few simple AT commands. The user only needs to use the specified AT command and pass the corresponding parameters to complete the parameter setting of the COFDM module.
Suitable Models
Command Introduction
The AT command for configuring COFDM module parameters starts with “AT” and ends with an underscore “_”. Each AT command has several or no parameters, and each AT command has a return value. For details, please refer to the introduction of the following commands.
Users can configure the parameters of the module through the configuration serial port (ಟಿಟಿಎಲ್ ಮಟ್ಟದ, 3.3ವಿ) of the COFDM module. For detailed serial port configuration, refer to the figure below. Please use tools such as “Serial Port Debugging Assistant” to send AT commands to the COFDM module, pay attention to the use of ಪಠ್ಯ, ಉದಾಹರಣೆಗೆ:
ಸಿommand Classification
The AT commands for configuring COFDM module parameters are mainly divided into the following two categories:
Query Commands | ಎಟಿಡಿಆರ್, ಎಟಿಜಿಡಿ, ATGE, ATGI , ಎಟಿಜಿಆರ್, ATGT, ATGB, ATGU, ATGIP |
Setting Commands | ATSD, ATSG, ATSM, ATSE, ATSI, ATSO, ಎಟಿಎಸ್ಆರ್, ATSP, ATST, ATSU,ATOSD, ATSIP |
From the perspective of whether to save after power-off, the setting commands can be divided into:
Power-off Saving Commands | ATSD, ATSE, ATSI, ATSO, ಎಟಿಎಸ್ಆರ್, ATSP, ATST, ATSU, ATSIP |
Power-off Not Saving Commands | ATSG, ATSM, ATOSD |
According to the configuration transmitter or receiver, the classification is as follows:
Sender Configuration Commands | ಎಟಿಡಿಆರ್, ATSD, ಎಟಿಜಿಡಿ, ATSG, ATSM, ATSE, ATGE, ATSI, ATGI, ATSO, ATSP, ATST, ATGT, ATSU, ATGU, ATOSD |
Receiver Configuration Commands | ಎಟಿಡಿಆರ್, ಎಟಿಎಸ್ಆರ್, ಎಟಿಜಿಆರ್, ATSP, ATST, ATGT, ATGB, ATSIP, ATGIP |
Command Details
Ping Command
ಸ್ವರೂಪ | ATDR_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ಬಳಸಿ | for the integrated system to check whether the serial port is connected and identify the connected modules. |
ಮೌಲ್ಯವನ್ನು ಹಿಂತಿರುಗಿಸಿ | RCB returns the “device profile” string SUE1 returns “ATDRSUE1 OK” string SHD1 returns “ATDRSHD1 OK” string |
ಟೀಕೆಗಳು | ಪ್ರಶ್ನೆ ಆಜ್ಞೆ |
Set Device Command
ಸ್ವರೂಪ | ATSD $(mimo), $(gi), $(COFDM ವೈರ್ಲೆಸ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ಸಿಸ್ಟಮ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ದರ ಲೆಕ್ಕಾಚಾರ), $ (constellation), $(ಆವರ್ತನ(KHz)), $(bw(KHz)), $(tx1_gain), $(tx2_gain)_ ಉದಾಹರಣೆ: ATSD0,1,0,0,800000,8000,86.0,86.0_ |
ಪ್ಯಾರಾಮೀಟರ್ | One Antenna/Dual antenna mimo: 0 mimo disable; 1 mimo enable Guard Interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1/4 Convolution Code Rate: 0 1/2; 1 2 /3; 2 3/4; 3 5/6; 4 7/8; ಕಾನ್ಸ್ಟೆಲ್ಲೇಷನ್: 0 QPSK; 1 QAM16; 2 QAM64; RCB Carrier Center Frequency(kHz) 200000~2700000(200MHz~2.7GHz, 1KHz ಹಂತ) RC900 Carrier center Frequency(kHz) 750000~930000(750ಮೆಗಾಹರ್ಟ್ಝ್ ~ 930MHz, 1KHz ಹಂತ) RCB Channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1KHz ಹಂತ) RCB Channel bandwidth bw(KHz) 2000~8000 (2MHz~8MHz, 1KHz ಹಂತ) Transmitting antenna 1 gain tx1_gain 0.0~89.75dB, 0.25dB stepping Transmitting antenna 2 gain tx2_gain 0.0~89.75dB, 0.25dB stepping |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆಗೆ:ATSD0,1,0,0,800000,8000,86.0,86.0_ SISO,ಜಿಐ: 1/16, ಸಿಆರ್:1/2, MOD: QPSK, ಆವರ್ತನ:800000KHz,bw:8000KHz,tx1_gain:86.000000 tx2_gain:86.000000 ಸರಿ |
ಸೂಚನೆ | Set command, save when power off. Different Bandwidths, ಗಾರ್ಡ್ ಮಧ್ಯಂತರಗಳು, Convolution code rates, Data rate calculation formulas corresponding to constellations Air interface rate Rate(COFDM ವೈರ್ಲೆಸ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ಸಿಸ್ಟಮ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ದರ ಲೆಕ್ಕಾಚಾರ) COFDM ವೈರ್ಲೆಸ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ಸಿಸ್ಟಮ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ದರ ಲೆಕ್ಕಾಚಾರ (ಬ್ಯಾಂಡ್ವಿಡ್ತ್(ಮೆಗಾಹರ್ಟ್ಝ್) * 8.0/7.0) / (1+ಜಿಐ) * 1512/2048*COFDM ವೈರ್ಲೆಸ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ಸಿಸ್ಟಮ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ದರ ಲೆಕ್ಕಾಚಾರ(COFDM ವೈರ್ಲೆಸ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ಸಿಸ್ಟಮ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ದರ ಲೆಕ್ಕಾಚಾರ) * COFDM ವೈರ್ಲೆಸ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ಸಿಸ್ಟಮ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ದರ ಲೆಕ್ಕಾಚಾರ * 188/204. Taking 8MHz bandwidth as an example, different guard intervals, convolution code rates, data rates corresponding to constellations and required receiving signal-to-noise ratios |
ಎಸ್et Gain Command
ಸ್ವರೂಪ | ATSG$( tx1_gain),$( tx1_gain)_ ಉದಾಹರಣೆ: ATSG85.0,85.0_ |
ಪ್ಯಾರಾಮೀಟರ್ | tx1_gain: ಟ್ರಾನ್ಸ್ಮಿಟರ್ 1 ಲಾಭ tx2_gain: ಟ್ರಾನ್ಸ್ಮಿಟರ್ 2 ಲಾಭ |
ಬಳಸಿ | To dynamically adjust the output power. If the signal SNR/RSSI of the receiver is high, the output power can be reduced through the remote control link. When the SNR/RSSI of the end signal is low, increase the output power (ಟ್ರಾನ್ಸ್ಮಿಟರ್) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ, | ಉದಾಹರಣೆ: ATSG85.0,85.0_set gain 85.000000 85.000000 ಸರಿ |
ಟೀಕೆಗಳು | ಆಜ್ಞೆಯನ್ನು ಹೊಂದಿಸುವುದು, power off will not save. |
Set Modulation Mode commanಡಿ
ಸ್ವರೂಪ | ATSM$(gi), $(COFDM ವೈರ್ಲೆಸ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ಸಿಸ್ಟಮ್ ಟ್ರಾನ್ಸ್ಮಿಷನ್ ದರ ಲೆಕ್ಕಾಚಾರ), $(constellation)_ ಉದಾಹರಣೆ: ATSM1,1,2_ |
ಪ್ಯಾರಾಮೀಟರ್ | Gard interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1 /4; Convolution code rate: 0 1/2; 1 2/3; 2 3/4; 3 5/6; 4 7/8; ಕಾನ್ಸ್ಟೆಲ್ಲೇಷನ್: 0 QPSK; 1 QAM16; 2 QAM64 |
ಬಳಸಿ | Dynamically adjust the air interface rate, the air interface rate can be increased when the distance is short, and the air interface rate can be reduced when the distance is long (ಟ್ರಾನ್ಸ್ಮಿಟರ್) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ:ATSM1,1,2_GI:1/16, ಸಿಆರ್:2/3, MOD: QAM64, ಸರಿ |
ಟೀಕೆಗಳು | ಆಜ್ಞೆಯನ್ನು ಹೊಂದಿಸುವುದು, power off will not save. |
ಜಿet Device Status Command
ಸ್ವರೂಪ | ATGD_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ಬಳಸಿ | query the current number of transmit antennas, ಸಿಬ್ಬಂದಿ ಮಧ್ಯಂತರದ, convolution code rate, number of constellations, transmit frequency, ಬ್ಯಾಂಡ್ವಿಡ್ತ್, gain parameters (ಟ್ರಾನ್ಸ್ಮಿಟರ್) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATGD_ SISO, ಜಿಐ:1 /16, ಸಿಆರ್: 1/2, MOD: QPSK, ಆವರ್ತನ: 800000KHz, bw: 8000KHz, tx1_gain: 86.000000 tx2_gain: 86.000000 ಸರಿ |
ಟೀಕೆಗಳು | ಪ್ರಶ್ನೆ ಆಜ್ಞೆ |
Set Encoder Command
ಸ್ವರೂಪ | ATSE$(llc),$(rt),$(bitrate) ,$(gop),$(ಆಡಿಯೋ)_ ಉದಾಹರಣೆ: ATSE0,0,0.0,0,0_ |
ಪ್ಯಾರಾಮೀಟರ್ | 1. Enhanced data reliability option llc: 0 disable; 1 enable (requires the receiving end to enable this option at the same time, use in pairs, because more redundant data is added to enhance reliability, the video bit rate of the transmitting end should be set when this option is turned off half of) 2. Real-time priority/quality priority rt: 0 image quality priority; 1 real-time priority; 3. ಬಿಟ್ರೇಟ್: 0 let system decide; >0 specify bitrate(float) 4. I frame interval GOP: 0 let system decide; >0 specify GOP 5. Audio encoding option audio: 0 disable; 1 enable |
ಬಳಸಿ | Used to set encoding parameters (ಟ್ರಾನ್ಸ್ಮಿಟರ್) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ:ATSE0, 0,0.0,0,0_ ಮೋಡ್:0,RT:0,bitrate: 0.0ಎಂಬಿಪಿಎಸ್,gop:0,ಆಡಿಯೋ:0,ಸರಿ |
ಟೀಕೆಗಳು | ಆಜ್ಞೆಯನ್ನು ಹೊಂದಿಸುವುದು, save when power is off. |
Get Encoder Command
ಸ್ವರೂಪ | ATGE_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ಬಳಸಿ | querying encoding parameters (sending end) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ:ATGE_MODE:0, RT:0,bitrate:4.0ಎಂಬಿಪಿಎಸ್,gop:10,ಆಡಿಯೋ:0,aes:0, ಸರಿ |
ಟೀಕೆಗಳು | Query command AES means the current encryption status: 0 disable; 1 enable |
Get Input Command
ಸ್ವರೂಪ | ATGI_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ಬಳಸಿ | query the current camera input parameters (ಟ್ರಾನ್ಸ್ಮಿಟರ್) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ:ATGI_input_size: 1080ಪು, input_rate: 60ಎಫ್ಪಿಎಸ್, sensor_type: hdmi,ಸರಿ |
ಟೀಕೆಗಳು | ಪ್ರಶ್ನೆ ಆಜ್ಞೆ |
Set Input Command
ಸ್ವರೂಪ | ATSI$(input_size),$(input_rate)_ ಉದಾಹರಣೆ: ATSI1080,25_ |
ಪ್ಯಾರಾಮೀಟರ್ | 1. Input resolution input_size: 0 ಸಿಸ್ಟಮ್ ಪತ್ತೆ ಮಾಡಲಿ; >0 specify input size 2. Input frame rate input_rate: 0 ಸಿಸ್ಟಮ್ ಪತ್ತೆ ಮಾಡಲಿ; > 0 specify input fps |
ಬಳಸಿ | To specify the input resolution and frame rate to meet some special signal sources, or some special application needs (ಟ್ರಾನ್ಸ್ಮಿಟರ್) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATSI1080,25_ Input_size:1080ಪು,input_rate: 25ಎಫ್ಪಿಎಸ್, ಸರಿ |
ರಿಮಾರ್ಕ್ಸ್ | After the user specifies the input resolution and frame rate through this command, the system will no longer detect the signal source (use with caution). The user can restore the default through the following command: ATSI0,0_Set the command and save it after power-off. |
Set Output Command
ಸ್ವರೂಪ | ATSO$(output_size),$(output_rate)_ ಉದಾಹರಣೆ: ATSO720,30_ |
ಪ್ಯಾರಾಮೀಟರ್ | 1. ಟ್ರಾನ್ಸ್ಮಿಟರ್: encoding output resolution output_size: 0 equal to input_size; >0 specify output size 2. ಸ್ವೀಕರಿಸುವವರ: HDMI output resolution (720, 1080) 3. ಟ್ರಾನ್ಸ್ಮಿಟರ್: encoding output frame rate output_rate: 0 equal to input_rate; >0 specify output_rate (ಎಫ್ಪಿಎಸ್) 4. ಸ್ವೀಕರಿಸುವವರ: HDMI output frame rate 720p supports frame rate (50, 60); 1080p supports frame rate (24, 25, 30, 50, 60) |
ಬಳಸಿ | 1. ಟ್ರಾನ್ಸ್ಮಿಟರ್: Used to specify the encoding output resolution and frame rate to meet the requirements of certain applications for zooming and frame reduction 2. ಸ್ವೀಕರಿಸುವವರ: used to configure the resolution and frame rate of HDMI output |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATSO720,30_ output_size: 720ಪು, output_rate: 30ಎಫ್ಪಿಎಸ್, ಸರಿ |
ರಿಮಾರ್ಕ್ಸ್ | 1. For HDMI input only, this command is invalid for AV input 2. Output_size <= input_size; output_rate<=input_rate 3. Set the command and save it after the power is off. |
ಇನ್ಪುಟ್ ಮೂಲಗಳ ಆಜ್ಞೆಯನ್ನು ಹೊಂದಿಸಿ (HDMI ಬದಲಿಸಿ / Cvbs ಇನ್ಪುಟ್)
ಸ್ವರೂಪ | ATSU$(ವಿನ್),$(ಐನ್)_ ಉದಾಹರಣೆ: ATSU0,1_ |
ಪ್ಯಾರಾಮೀಟರ್ | 1. ವೀಡಿಯೊ ಇನ್ಪುಟ್ ಆಯ್ಕೆ VIN: 0 ಸಿಸ್ಟಮ್ ಪತ್ತೆ ಮಾಡಲಿ; 1 CVBS ಇನ್ಪುಟ್ ಅನ್ನು ಒತ್ತಾಯಿಸಿ; 2 hdmi/SDI ಇನ್ಪುಟ್ ಅನ್ನು ಒತ್ತಾಯಿಸಿ 2. ಆಡಿಯೊ ಇನ್ಪುಟ್ ಆಯ್ಕೆ AIN: 0 ಸಿಸ್ಟಮ್ ಪತ್ತೆ ಮಾಡಲಿ; 1 ಬಲ ಅನಲಾಗ್ ಇನ್ಪುಟ್ |
ಬಳಸಿ | ನಿರ್ದಿಷ್ಟ ಅಪ್ಲಿಕೇಶನ್ ಅವಶ್ಯಕತೆಗಳನ್ನು ಪೂರೈಸಲು ಬಳಸಲಾಗುತ್ತದೆ (ಉದಾಹರಣೆ: HDMI/SDI ಇನ್ಪುಟ್ ವೀಡಿಯೊ, MIC ಇನ್ಪುಟ್ ಆಡಿಯೋ) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATSU0,1_ ATSU0,1 ಸರಿ |
ಟೀಕೆಗಳು | ಆಜ್ಞೆಯನ್ನು ಹೊಂದಿಸುವುದು, ವಿದ್ಯುತ್ ಆಫ್ ಉಳಿತಾಯ. |
Get User Command
ಸ್ವರೂಪ | ATGU _ ಉದಾಹರಣೆ: ATGU_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ಬಳಸಿ | To query user-specific configuration |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATGU_ ATGU0,1 OK |
ಟೀಕೆಗಳು | ಪ್ರಶ್ನೆ ಆಜ್ಞೆ return parameter description please refer to the ATSU command |
Set Receiver Command
ಸ್ವರೂಪ | ಎಟಿಎಸ್ಆರ್ $(ಆವರ್ತನ), $(bw ), $(llc), $(cvbs)_ ಉದಾಹರಣೆ: ATSR320000,6000,0,0_ |
ಪ್ಯಾರಾಮೀಟರ್ | 1. DR2C carrier frequency freq(KHz) 200000~860000(200ಮೆಗಾಹರ್ಟ್ಝ್ ~ 860MHz, 1KHz ಹಂತ) 2. DR900 carrier center frequency freq(KHz) 200000~1600000(200MHz~1.6GHz, 1KHz ಹಂತ) 3. DR2C channel bandwidth bw(KHz) 2000~8000(2MHz~8MHz, 1KHz ಹಂತ) 4. DR900 channel bandwidth bw(KHz) 3200~8000(3.2MHz~8MHz, 1KHz ಹಂತ) 5. Enhanced data reliability option llc: 0 disable; 1 enable (it is required that the transmitter should also enable this option at the same time, and use it in pairs. Since more redundant data is added to enhance reliability, the video bit rate of the transmitter should be set to when this option is turned off half of) 6. AV output system cvbs: 0 pal; 1 ntsc |
ಬಳಸಿ | To set the receiver parameter |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | example: ATSR320000,6000,0,0_ ATSR320000,6000,0,0 OK |
ಟೀಕೆಗಳು | ಆಜ್ಞೆಯನ್ನು ಹೊಂದಿಸುವುದು, save when power is off. |
Get Receiver Command
ಸ್ವರೂಪ | ATGR_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ATGR_ | the receiving end parameter |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATGR_ ATGR320000,6000,0,aes:0,cvbs:0 ಸರಿ |
ಟೀಕೆಗಳು | 1. Query command 2. Aes parameter indicates the current encryption status: 0 disable;1 enable 3. CVBS parameter Indicates the current AV output standard: 0 pal;1 ntsc |
Get Bit Error Rate Command
ಸ್ವರೂಪ | ATGB_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ಬಳಸಿ | querying the bit error rate and signal strength of the dual antennas at the receiving end |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATGB_ ATGB ber1:0.00% ber2:0.00% RSSI1 :54 RSSI2:53 Lock1:1 Lock2:1 ಸರಿ |
ರಿಮಾರ್ಕ್ಸ್ | 1. Query commands 2. Ber1 and ber2 respectively indicate the bit error rate of each antenna, ranging from 0.0% ಗೆ 100.0% 3. RSSI1 and RSSI2 respectively indicate the signal strength of each antenna, ranging from 0 ಗೆ 100 4. Lock1 and Lock2 respectively indicate the signal locking status of each antenna (1 Represents signal lock) |
Set Password Command
ಸ್ವರೂಪ | ATSP$(ಗುಪ್ತಪದ), $(ಗುಪ್ತಪದ)_ ಉದಾಹರಣೆ: ATSP123456, 123456_ |
ಪ್ಯಾರಾಮೀಟರ್ | AES key password: 6-digit password (ASCII) AES key password: 6-digit password (ASCII) (repeat it for confirmation) |
ಬಳಸಿ | Used to set the AES key of the transceiver (ಯಂತ್ರ ಮತ್ತು ಗ್ರಾಹಕದ) |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATSP123456_ ATSP123456 OK |
ಟೀಕೆಗಳು | 1. When the password is all 0, AES encryption is turned off. 2. Set the command and save it after powering it off. |
Set Data Transfer Command
ಸ್ವರೂಪ | ATST$(ಬೌಡ್ ದರ), $( parity)_ ಉದಾಹರಣೆ: ATST115200,0_ |
ಪ್ಯಾರಾಮೀಟರ್ | 1. Baud rate baud rate: 1200、2400、4800、9600、19200、38400、57600、115200 2. Check Code: 0: ಯಾವುದೂ; 1: Odd; 2: ಸಹ |
ಬಳಸಿ | Used to set the baud rate and parity bit of the serial port for data transparent transmission |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATST115200,0_ ATST115200,0 OK |
ರಿಮಾರ್ಕ್ಸ್ | Set command |
Get Data Transfer Command
ಸ್ವರೂಪ | ATGT_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ಬಳಸಿ | Used to query the baud rate and check code |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATGT_ ATGT115200,0 OK |
ರಿಮಾರ್ಕ್ಸ್ | Query command |
Set IP Address Command
ಸ್ವರೂಪ | ATSIP$(ip), $(ip)_ ಉದಾಹರಣೆ: ATSIP192.168.1.215,192.168.1.215_ |
ನಿಯತಾಂಕಗಳು | Local IP address Local IP address (repeat to confirm) |
ಬಳಸಿ | Used to set the receiver IP address |
ರಿಟರ್ನ್ ಮೌಲ್ಯ | ಉದಾಹರಣೆ: ATSIP_192.168.1 .215,192.168.1.215_ ATSIP192.168.1.215 OK |
ರಿಮಾರ್ಕ್ಸ್ | 1. After setting the IP address, the receiving end needs to be restarted to take effect. 2. Set the command and save it after powering it off. |
Get IP Address Command
ಸ್ವರೂಪ | ATGIP_ ಉದಾಹರಣೆ: ATGIP_ |
ಪ್ಯಾರಾಮೀಟರ್ | ಯಾವುದೇ |
ಬಳಸಿ | ಸ್ವೀಕರಿಸುವ ಅಂತ್ಯದ ಪ್ರಸ್ತುತ IP ವಿಳಾಸವನ್ನು ಪ್ರಶ್ನಿಸಲು |
ಮೌಲ್ಯವನ್ನು ಹಿಂತಿರುಗಿಸಿ | ಉದಾಹರಣೆ: ATGIP_ ATGIP192.168.0.215 ಸರಿ |
ಟೀಕೆಗಳು | ಪ್ರಶ್ನೆ ಆಜ್ಞೆ |
OSD Overlay Protocol
ಸ್ವರೂಪ | ATOSD$(idx), $(ಎಕ್ಸ್), $(y), $(str)_ ಉದಾಹರಣೆ:ATOSD0,40,20,height: 100m_ |
ಪ್ಯಾರಾಮೀಟರ್ | 1. IDX index: 0~7 (supports OSD overlay for 8 areas) 2. X-coordinate: 0~1919 3. Y coordinate: 0~1079 4. str: the string to be displayed at the corresponding coordinates (the space symbol is used to clear the display) |
ಬಳಸಿ | on the video screen.OSD information |
ಮೌಲ್ಯವನ್ನು ಹಿಂತಿರುಗಿಸಿ | ಯಾವುದೇ |
ರಿಮಾರ್ಕ್ಸ್ | 1. The user specifies the x and y coordinates of the OSD display according to the maximum 1920×1080 ಪಿಕ್ಸೆಲ್ಗಳು, and the system will correct the coordinates according to the actual display situation. 2. The ‘_’ character cannot be contained in the str parameter |
Set Gain To Adjust
ಸ್ವರೂಪ | ATSAD$(ಆವರ್ತನ),$(adjust) _ ಉದಾಹರಣೆ:ATSAD700000,2.5_ |
ಪ್ಯಾರಾಮೀಟರ್ | wireless central working frequency: Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) Adjust the value(ಡಿಬಿ): ATSD cmd will subtract this value to set the wireless gain |
ಕಾರ್ಯ | Specify and adjust the value for the wireless gain setting using by ATSD cmd |
ಪ್ರತಿಕ್ರಿಯೆ | ಉದಾಹರಣೆ: ATSAD700000,2.5_ freq:700000,adjust:2.50 ಸರಿ |
ಕಾಮೆಂಟ್ಗಳು | Setting command is still valid when stopping power or resetting. |
Get Gain To Adjust
ಸ್ವರೂಪ | ATGAD[$(ಆವರ್ತನ)]_ ಉದಾಹರಣೆ:ATGAD700000_ |
ಪ್ಯಾರಾಮೀಟರ್ | wireless central working frequency: Freq(KHz) 200000~2700000(200MHz~2.7GHz, step: 1KHz) When no parameter provides, it will list all the freq that have adjusted value. |
ಕಾರ್ಯ | Inquiry adjust the value for wireless gain setting using ATSD cmd |
ಪ್ರತಿಕ್ರಿಯೆ | ಉದಾಹರಣೆ: ATGAD700000_ freq:700000,adjust:2.50 OK ATGAD_ freq:700000 750000 ಸರಿ |
ಕಾಮೆಂಟ್ಗಳು | Inquiry command. |
Serial Port Utility software download
HTTPS://www.alithon.com/downloads
ಎಫ್ಎಕ್ಯೂ
1. How can I return to the No Password setting with 000000 indications after the change?
Reset the password to 000000 (one must not be missing) through the Parameter Configuration Panel Board.
or set it through ದಿ ATSP_command
2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (ಗಳಿಕೆ) good for linear output operation? Or do you suggest some limited range for better linear operation?
The Gain of the COFDM configuration is the internal Gain, not the actual output power of the transmitter. The internal gain range is 0~89.75dB and the linear output:
1. At around 300~500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -5dBm.
2. At around 1000~1500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -6dBm to -10dBm.
3. I tried to set – B bandwidth (kHz) and E bit rate (ಎಂಬಿಪಿಎಸ್). When I set E, the new value does not apply. So. the E setting is only for monitoring of available bitrate? if I wish to change the E (ಬಿಟ್ರೇಟ್) I have to change only B (ಬ್ಯಾಂಡ್ವಿಡ್ತ್)? Am I right?
It is not recommended to modify the video bit rate ‘E’ directly, because if the output video bit rate is greater than the wireless air interface rate, the system will not work normally.
By default, the internal video bit rate ‘E’ will be set to 0 for automatic. Customers only need to modify ‘B’ to modify the wireless parameters, and the video bit rate will automatically adapt.
You can also adjust the wireless air interface rate by modifying GI and CR.
For more details on the Encoder Modulator Decoder Demodulator Module, please send an inquiry to us.
COFDM ಮಾಡ್ಯುಲೇಟರ್ ಡೆಮೊಡ್ಯುಲೇಟರ್ ಮಾಡ್ಯೂಲ್ ಎನ್ಕೋಡರ್ ಡಿಕೋಡರ್ HDMI CVBS AV ಇನ್ಪುಟ್ AES 256 FHD RF ಸ್ಟ್ರೀಮಿಂಗ್
$0.00
ವಿಮರ್ಶೆಗಳು
ಯಾವುದೇ ವಿಮರ್ಶೆಗಳು ಇನ್ನೂ ಇವೆ.