Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions COFDM AT Command
Download the Encoder Modulator Decoder Demodulator Module Parameter Configuration Instructions below if you need a PDF file.
Update Record:
આવૃત્તિ | તારીખ | વર્ણન |
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 | 2016-10-24 2016-11-1 2016-12-26 2017-2-14 2017-2-28 2017-3-27 2017-4-19 2017-5-18 2017-9-12 2018-3-15 2019-6-25 2023-2-24 | Initial version ATDR reply distinguishing module ATSE, ATGE add audio switch Add ATSP protocol Add ATST, ATGT protocol ATGE command add AESfor status acquisition Added ATGB protocol AV and HDMI output control Support for obtaining the current AV output standard Added ATSU, ATGUcommands Added ATOSD, ATSIP, ATGIP commands Added ATSAD, ATGAD commands |
Users may need to modify the configuration parameters of the module during the use of the COFDM modulator and demodulator module. In order to simplify the user’s operation, we design the parameter configuration into a few simple AT commands. The user only needs to use the specified AT command and pass the corresponding parameters to complete the parameter setting of the COFDM module.
Suitable Models
Command Introduction
The AT command for configuring COFDM module parameters starts with “એટી” and ends with an underscore “_”. Each AT command has several or no parameters, and each AT command has a return value. For details, please refer to the introduction of the following commands.
Users can configure the parameters of the module through the configuration serial port (TTL સ્તર, 3.3વી) of the COFDM module. For detailed serial port configuration, refer to the figure below. Please use tools such as “Serial Port Debugging Assistant” to send AT commands to the COFDM module, pay attention to the use of ટેક્સ્ટ, દાખ્લા તરીકે:
સીommand Classification
The AT commands for configuring COFDM module parameters are mainly divided into the following two categories:
Query Commands | ATDR, ATGD, ATGE, ATGI , ATGR, ATGT, ATGB, ATGU, ATGIP |
Setting Commands | ATSD, ATSG, ATSM, ATSE, ATSI, ATSO, ATSR, ATSP, ATST, ATSU,ATOSD, ATSIP |
From the perspective of whether to save after power-off, the setting commands can be divided into:
Power-off Saving Commands | ATSD, ATSE, ATSI, ATSO, ATSR, ATSP, ATST, ATSU, ATSIP |
Power-off Not Saving Commands | ATSG, ATSM, ATOSD |
According to the configuration transmitter or receiver, the classification is as follows:
Sender Configuration Commands | ATDR, ATSD, ATGD, ATSG, ATSM, ATSE, ATGE, ATSI, ATGI, ATSO, ATSP, ATST, ATGT, ATSU, ATGU, ATOSD |
Receiver Configuration Commands | ATDR, ATSR, ATGR, ATSP, ATST, ATGT, ATGB, ATSIP, ATGIP |
Command Details
Ping Command
ફોર્મેટ | ATDR_ |
પરિમાણ | કોઈ |
વાપરવુ | for the integrated system to check whether the serial port is connected and identify the connected modules. |
વળતર મૂલ્ય | RCB returns the “device profile” string SUE1 returns “ATDRSUE1 OK” string SHD1 returns “ATDRSHD1 OK” string |
રીમાર્ક | ક્વેરી આદેશ |
Set Device Command
ફોર્મેટ | ATSD $(mimo), $(gi), $(COFDM વાયરલેસ ટ્રાન્સમિશન સિસ્ટમ ટ્રાન્સમિશન દર ગણતરી), $ (constellation), $(આવર્તન(મેગાહર્ટઝ)), $(bw(મેગાહર્ટઝ)), $(tx1_gain), $(tx2_gain)_ ઉદાહરણ: ATSD0,1,0,0,800000,8000,86.0,86.0_ |
પરિમાણ | One Antenna/Dual antenna mimo: 0 mimo disable; 1 mimo enable Guard Interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1/4 Convolution Code Rate: 0 1/2; 1 2 /3; 2 3/4; 3 5/6; 4 7/8; નક્ષત્ર: 0 QPSK; 1 QAM16; 2 QAM64; RCB Carrier Center Frequency(કિલોહર્ટઝ) 200000~2700000(200MHz~2.7GHz, 1KHz પગલું) RC900 Carrier center Frequency(કિલોહર્ટઝ) 750000~930000(750મેગાહર્ટઝ ~ 930MHz, 1KHz પગલું) RCB Channel bandwidth bw(મેગાહર્ટઝ) 2000~8000(2MHz~8MHz, 1KHz પગલું) RCB Channel bandwidth bw(મેગાહર્ટઝ) 2000~8000 (2MHz~8MHz, 1KHz પગલું) Transmitting antenna 1 gain tx1_gain 0.0~89.75dB, 0.25dB stepping Transmitting antenna 2 gain tx2_gain 0.0~89.75dB, 0.25dB stepping |
Return Value | જેમ કે:ATSD0,1,0,0,800000,8000,86.0,86.0_ SISO,જીઆઇ: 1/16, સીઆર:1/2, MOD: QPSK, આવર્તન:800000મેગાહર્ટઝ,bw:8000મેગાહર્ટઝ,tx1_gain:86.000000 tx2_gain:86.000000 ઠીક છે |
નૉૅધ | આદેશ સેટ કરો, પાવર બંધ થાય ત્યારે સાચવો. Different Bandwidths, ગાર્ડ અંતરાલો, Convolution code rates, Data rate calculation formulas corresponding to constellations Air interface rate Rate(COFDM વાયરલેસ ટ્રાન્સમિશન સિસ્ટમ ટ્રાન્સમિશન દર ગણતરી) COFDM વાયરલેસ ટ્રાન્સમિશન સિસ્ટમ ટ્રાન્સમિશન દર ગણતરી (બેન્ડવીડ્થ(મેગાહર્ટઝ) * 8.0/7.0) / (1+જીઆઇ) * 1512/2048*COFDM વાયરલેસ ટ્રાન્સમિશન સિસ્ટમ ટ્રાન્સમિશન દર ગણતરી(COFDM વાયરલેસ ટ્રાન્સમિશન સિસ્ટમ ટ્રાન્સમિશન દર ગણતરી) * COFDM વાયરલેસ ટ્રાન્સમિશન સિસ્ટમ ટ્રાન્સમિશન દર ગણતરી * 188/204. Taking 8MHz bandwidth as an example, different guard intervals, convolution code rates, data rates corresponding to constellations and required receiving signal-to-noise ratios |
એસet Gain Command
ફોર્મેટ | ATSG$( tx1_gain),$( tx1_gain)_ ઉદાહરણ: ATSG85.0,85.0_ |
પરિમાણ | tx1_gain: ટ્રાન્સમીટર 1 લાભ tx2_gain: ટ્રાન્સમીટર 2 લાભ |
વાપરવુ | To dynamically adjust the output power. If the signal SNR/RSSI of the receiver is high, the output power can be reduced through the remote control link. When the SNR/RSSI of the end signal is low, increase the output power (ટ્રાન્સમીટર) |
Return Value, | ઉદાહરણ: ATSG85.0,85.0_set gain 85.000000 85.000000 ઠીક છે |
રીમાર્ક | setting command, power off will not save. |
Set Modulation Mode commanડી
ફોર્મેટ | ATSM$(gi), $(COFDM વાયરલેસ ટ્રાન્સમિશન સિસ્ટમ ટ્રાન્સમિશન દર ગણતરી), $(constellation)_ ઉદાહરણ: ATSM1,1,2_ |
પરિમાણ | Gard interval GI: 0 1/32; 1 1/16; 2 1/8; 3 1 /4; Convolution code rate: 0 1/2; 1 2/3; 2 3/4; 3 5/6; 4 7/8; નક્ષત્ર: 0 QPSK; 1 QAM16; 2 QAM64 |
વાપરવુ | Dynamically adjust the air interface rate, the air interface rate can be increased when the distance is short, and the air interface rate can be reduced when the distance is long (ટ્રાન્સમીટર) |
Return Value | ઉદાહરણ:ATSM1,1,2_GI:1/16, સીઆર:2/3, MOD: QAM64, ઠીક છે |
રીમાર્ક | setting command, power off will not save. |
જીet Device Status Command
ફોર્મેટ | ATGD_ |
પરિમાણ | કોઈ |
વાપરવુ | query the current number of transmit antennas, રક્ષક અંતરાલ, convolution code rate, number of constellations, transmit frequency, બેન્ડવિડ્થ, gain parameters (ટ્રાન્સમીટર) |
Return Value | ઉદાહરણ: ATGD_ SISO, જીઆઇ:1 /16, સીઆર: 1/2, MOD: QPSK, આવર્તન: 800000મેગાહર્ટઝ, bw: 8000મેગાહર્ટઝ, tx1_gain: 86.000000 tx2_gain: 86.000000 ઠીક છે |
રીમાર્ક | ક્વેરી આદેશ |
Set Encoder Command
ફોર્મેટ | ATSE$(llc),$(rt),$(bitrate) ,$(gop),$(ઓડિયો)_ ઉદાહરણ: ATSE0,0,0.0,0,0_ |
પરિમાણ | 1. Enhanced data reliability option llc: 0 disable; 1 enable (requires the receiving end to enable this option at the same time, use in pairs, because more redundant data is added to enhance reliability, the video bit rate of the transmitting end should be set when this option is turned off half of) 2. Real-time priority/quality priority rt: 0 image quality priority; 1 real-time priority; 3. બિટરેટ: 0 let system decide; >0 specify bitrate(float) 4. I frame interval GOP: 0 let system decide; >0 specify GOP 5. Audio encoding option audio: 0 disable; 1 enable |
વાપરવુ | Used to set encoding parameters (ટ્રાન્સમીટર) |
Return Value | ઉદાહરણ:ATSE0, 0,0.0,0,0_ MODE:0,RT:0,bitrate: 0.0એમબીપીએસ,gop:0,ઓડિયો:0,ઠીક છે |
રીમાર્ક | setting command, save when power is off. |
Get Encoder Command
ફોર્મેટ | ATGE_ |
પરિમાણ | કોઈ |
વાપરવુ | querying encoding parameters (sending end) |
Return Value | ઉદાહરણ:ATGE_MODE:0, RT:0,bitrate:4.0એમબીપીએસ,gop:10,ઓડિયો:0,aes:0, ઠીક છે |
રીમાર્ક | Query command AES means the current encryption status: 0 disable; 1 enable |
Get Input Command
ફોર્મેટ | ATGI_ |
પરિમાણ | કોઈ |
વાપરવુ | query the current camera input parameters (ટ્રાન્સમીટર) |
Return Value | ઉદાહરણ:ATGI_input_size: 1080પી, input_rate: 60FPS, sensor_type: hdmi,ઠીક છે |
રીમાર્ક | ક્વેરી આદેશ |
Set Input Command
ફોર્મેટ | ATSI$(input_size),$(input_rate)_ ઉદાહરણ: ATSI1080,25_ |
પરિમાણ | 1. Input resolution input_size: 0 let the system detect; >0 specify input size 2. Input frame rate input_rate: 0 let the system detect; > 0 specify input fps |
વાપરવુ | To specify the input resolution and frame rate to meet some special signal sources, or some special application needs (ટ્રાન્સમીટર) |
Return Value | ઉદાહરણ: ATSI1080,25_ Input_size:1080પી,input_rate: 25FPS, ઠીક છે |
રીમાર્કસ | After the user specifies the input resolution and frame rate through this command, the system will no longer detect the signal source (use with caution). The user can restore the default through the following command: ATSI0,0_Set the command and save it after power-off. |
Set Output Command
ફોર્મેટ | ATSO$(output_size),$(output_rate)_ ઉદાહરણ: ATSO720,30_ |
પરિમાણ | 1. ટ્રાન્સમીટર: encoding output resolution output_size: 0 equal to input_size; >0 specify output size 2. રીસીવર: HDMI output resolution (720, 1080) 3. ટ્રાન્સમીટર: encoding output frame rate output_rate: 0 equal to input_rate; >0 specify output_rate (FPS) 4. રીસીવર: HDMI output frame rate 720p supports frame rate (50, 60); 1080p supports frame rate (24, 25, 30, 50, 60) |
વાપરવુ | 1. ટ્રાન્સમીટર: Used to specify the encoding output resolution and frame rate to meet the requirements of certain applications for zooming and frame reduction 2. રીસીવર: used to configure the resolution and frame rate of HDMI output |
Return Value | ઉદાહરણ: ATSO720,30_ output_size: 720પી, output_rate: 30FPS, ઠીક છે |
રીમાર્કસ | 1. For HDMI input only, this command is invalid for AV input 2. Output_size <= input_size; output_rate<=input_rate 3. Set the command and save it after the power is off. |
Set Input Sources Command (switch HDMI / CVBS ઇનપુટ)
ફોર્મેટ | ATSU$(vin),$(ain)_ ઉદાહરણ: ATSU0,1 _ |
પરિમાણ | 1. Video input selection VIN: 0 let the system detect; 1 force CVBS input; 2 force hdmi/SDI input 2. Audio input selection AIN: 0 let the system detect; 1 force analog input |
વાપરવુ | Used to meet specific application requirements (ઉદાહરણ: HDMI/SDI input video, MIC input audio) |
Return Value | ઉદાહરણ: ATSU0,1_ ATSU0,1 OK |
રીમાર્ક | setting command, power-off save. |
Get User Command
ફોર્મેટ | ATGU _ ઉદાહરણ: ATGU_ |
પરિમાણ | કોઈ |
વાપરવુ | To query user-specific configuration |
Return Value | ઉદાહરણ: ATGU_ ATGU0,1 OK |
રીમાર્ક | ક્વેરી આદેશ return parameter description please refer to the ATSU command |
Set Receiver Command
ફોર્મેટ | ATSR $(આવર્તન), $(bw ), $(llc), $(cvbs)_ ઉદાહરણ: ATSR320000,6000,0,0_ |
પરિમાણ | 1. DR2C carrier frequency freq(મેગાહર્ટઝ) 200000~860000(200મેગાહર્ટઝ ~ 860MHz, 1KHz પગલું) 2. DR900 carrier center frequency freq(મેગાહર્ટઝ) 200000~1600000(200MHz~1.6GHz, 1KHz પગલું) 3. DR2C channel bandwidth bw(મેગાહર્ટઝ) 2000~8000(2MHz~8MHz, 1KHz પગલું) 4. DR900 channel bandwidth bw(મેગાહર્ટઝ) 3200~8000(3.2MHz~8MHz, 1KHz પગલું) 5. Enhanced data reliability option llc: 0 disable; 1 enable (it is required that the transmitter should also enable this option at the same time, and use it in pairs. Since more redundant data is added to enhance reliability, the video bit rate of the transmitter should be set to when this option is turned off half of) 6. AV output system cvbs: 0 pal; 1 ntsc |
વાપરવુ | To set the receiver parameter |
Return Value | example: ATSR320000,6000,0,0_ ATSR320000,6000,0,0 OK |
રીમાર્ક | setting command, save when power is off. |
Get Receiver Command
ફોર્મેટ | ATGR_ |
પરિમાણ | કોઈ |
ATGR_ | the receiving end parameter |
Return Value | ઉદાહરણ: ATGR_ ATGR320000,6000,0,aes:0,cvbs:0 ઠીક છે |
રીમાર્ક | 1. Query command 2. Aes parameter indicates the current encryption status: 0 disable;1 enable 3. CVBS parameter Indicates the current AV output standard: 0 pal;1 ntsc |
Get Bit Error Rate Command
ફોર્મેટ | ATGB_ |
પરિમાણ | કોઈ |
વાપરવુ | querying the bit error rate and signal strength of the dual antennas at the receiving end |
Return Value | ઉદાહરણ: ATGB_ ATGB ber1:0.00% ber2:0.00% RSSI1 :54 RSSI2:53 Lock1:1 Lock2:1 ઠીક છે |
રીમાર્કસ | 1. Query commands 2. Ber1 and ber2 respectively indicate the bit error rate of each antenna, ranging from 0.0% માટે 100.0% 3. RSSI1 and RSSI2 respectively indicate the signal strength of each antenna, ranging from 0 માટે 100 4. Lock1 and Lock2 respectively indicate the signal locking status of each antenna (1 Represents signal lock) |
Set Password Command
ફોર્મેટ | ATSP$(પાસવર્ડ), $(પાસવર્ડ)_ ઉદાહરણ: ATSP123456, 123456_ |
પરિમાણ | AES કી પાસવર્ડ: 6-digit password (ASCII) AES કી પાસવર્ડ: 6-digit password (ASCII) (repeat it for confirmation) |
વાપરવુ | ટ્રાન્સસીવરની AES કી સેટ કરવા માટે વપરાય છે (ટ્રાન્સમિટર અને રિસીવર) |
Return Value | ઉદાહરણ: ATSP123456_ ATSP123456 ઓકે |
રીમાર્ક | 1. જ્યારે પાસવર્ડ બધા છે 0, AES encryption is turned off. 2. Set the command and save it after powering it off. |
Set Data Transfer Command
ફોર્મેટ | ATST$(baud દર), $( parity)_ ઉદાહરણ: ATST115200,0_ |
પરિમાણ | 1. Baud rate baud rate: 1200、2400、4800、9600、19200、38400、57600、115200 2. Check Code: 0: કોઈ નહિ; 1: Odd; 2: Even |
વાપરવુ | Used to set the baud rate and parity bit of the serial port for data transparent transmission |
Return Value | ઉદાહરણ: ATST115200,0_ ATST115200,0 OK |
રીમાર્કસ | આદેશ સેટ કરો |
Get Data Transfer Command
ફોર્મેટ | ATGT_ |
પરિમાણ | કોઈ |
વાપરવુ | Used to query the baud rate and check code |
Return Value | ઉદાહરણ: ATGT_ ATGT115200,0 OK |
રીમાર્કસ | Query command |
Set IP Address Command
ફોર્મેટ | ATSIP$(ip), $(ip)_ ઉદાહરણ: ATSIP192.168.1.215,192.168.1.215_ |
પરિમાણો | Local IP address Local IP address (પુષ્ટિ કરવા માટે પુનરાવર્તન કરો) |
વાપરવુ | Used to set the receiver IP address |
Return Value | ઉદાહરણ: ATSIP_192.168.1 .215,192.168.1.215_ ATSIP192.168.1.215 OK |
રીમાર્કસ | 1. After setting the IP address, the receiving end needs to be restarted to take effect. 2. Set the command and save it after powering it off. |
Get IP Address Command
ફોર્મેટ | ATGIP_ ઉદાહરણ: ATGIP_ |
પરિમાણ | કોઈ |
વાપરવુ | પ્રાપ્ત અંતના વર્તમાન IP સરનામાંની ક્વેરી કરવા માટે |
વળતર મૂલ્ય | ઉદાહરણ: ATGIP_ ATGIP192.168.0.215 ઓકે |
રીમાર્ક | ક્વેરી આદેશ |
OSD Overlay Protocol
ફોર્મેટ | ATOSD$(idx), $(એક્સ), $(y), $(str)_ ઉદાહરણ:ATOSD0,40,20,height: 100m_ |
પરિમાણ | 1. IDX index: 0~7 (supports OSD overlay for 8 areas) 2. X-coordinate: 0~1919 3. Y coordinate: 0~1079 4. str: the string to be displayed at the corresponding coordinates (the space symbol is used to clear the display) |
વાપરવુ | on the video screen.OSD information |
વળતર મૂલ્ય | કોઈ |
રીમાર્કસ | 1. The user specifies the x and y coordinates of the OSD display according to the maximum 1920×1080 પિક્સેલ્સ, and the system will correct the coordinates according to the actual display situation. 2. The ‘_’ character cannot be contained in the str parameter |
Set Gain To Adjust
ફોર્મેટ | ATSAD$(આવર્તન),$(adjust) _ ઉદાહરણ:ATSAD700000,2.5_ |
પરિમાણ | wireless central working frequency: આવર્તન(મેગાહર્ટઝ) 200000~2700000(200MHz~2.7GHz, step: 1મેગાહર્ટઝ) Adjust the value(ડીબી): ATSD cmd will subtract this value to set the wireless gain |
કાર્ય | Specify and adjust the value for the wireless gain setting using by ATSD cmd |
પ્રતિસાદ | ઉદાહરણ: ATSAD700000,2.5_ freq:700000,adjust:2.50 ઠીક છે |
ટિપ્પણીઓ | Setting command is still valid when stopping power or resetting. |
Get Gain To Adjust
ફોર્મેટ | ATGAD[$(આવર્તન)]_ ઉદાહરણ:ATGAD700000_ |
પરિમાણ | wireless central working frequency: આવર્તન(મેગાહર્ટઝ) 200000~2700000(200MHz~2.7GHz, step: 1મેગાહર્ટઝ) When no parameter provides, it will list all the freq that have adjusted value. |
કાર્ય | Inquiry adjust the value for wireless gain setting using ATSD cmd |
પ્રતિસાદ | ઉદાહરણ: ATGAD700000_ freq:700000,adjust:2.50 OK ATGAD_ freq:700000 750000 ઠીક છે |
ટિપ્પણીઓ | Inquiry command. |
Serial Port Utility software download
https://www.alithon.com/downloads
FAQ
1. How can I return to the No Password setting with 000000 indications after the change?
Reset the password to 000000 (one must not be missing) through the Parameter Configuration Panel Board.
or set it through આ ATSP_command
2. I see that Gain is the output power of the transmitter. Please tell me the range of settings of this parameter. All setting level (પ્રાપ્તિ) good for linear output operation? Or do you suggest some limited range for better linear operation?
The Gain of the COFDM configuration is the internal Gain, not the actual output power of the transmitter. The internal gain range is 0~89.75dB and the linear output:
1. At around 300~500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -5dBm.
2. At around 1000~1500MHz, the Gain is set to 89.75, and the actual output power of the transmitter module is about -6dBm to -10dBm.
3. I tried to set – B bandwidth (કિલોહર્ટઝ) and E bit rate (એમબીપીએસ). When I set E, the new value does not apply. તેથી. the E setting is only for monitoring of available bitrate? if I wish to change the E (બિટરેટ) I have to change only B (બેન્ડવિડ્થ)? Am I right?
It is not recommended to modify the video bit rate ‘E’ directly, because if the output video bit rate is greater than the wireless air interface rate, the system will not work normally.
By default, the internal video bit rate ‘E’ will be set to 0 for automatic. Customers only need to modify ‘B’ to modify the wireless parameters, and the video bit rate will automatically adapt.
You can also adjust the wireless air interface rate by modifying GI and CR.
For more details on the Encoder Modulator Decoder Demodulator Module, please send an inquiry to us.
COFDM મોડ્યુલેટર ડિમોડ્યુલેટર મોડ્યુલ એન્કોડર ડીકોડર HDMI CVBS AV ઇનપુટ AES 256 FHD RF સ્ટ્રીમિંગ
સમીક્ષાઓ
કોઈ સમીક્ષાઓ હજુ સુધી છે.