22km isema ni itukutuku isema ni vidio RC ni isema ni ip ethernet itaba veilawa transmitter kei na receiver fhss Vcan1806

22km wireless video data RC control link for IP camera long-range ethernet camera transmitter and receiver fhss

The wireless video data RC control link realizes long-range two-way wireless video, vakarorogo, and data transmission, and the longest air-to-ground transmission distance can reach about 22km.

The wireless video data RC control link provides multiple service interfaces, oka kina na 3 Gacagaca ni Icanet, 1 RS232 na ikelekele ni waqa, kei na 1 control serial port.

There is more and more unmanned equipment, and the mutual interference between links is becoming more and more serious. The anti-interference ability of the link is particularly important. For this reason, we specially launched a strong anti-interference video transmission, which supports automatic jumping of 22 veika e dau yaco. frequency supports 15-150 kilometers transmission distance, supports dual network ports 4 gacagaca ni soqo (232, TTL, 485, 422 vakatau vei iko), 2-way Sbus, supports high and low temperatures -40 me +85 ivakatagedegede. Support point-to-point, point-to-multipoint, Mesh ad hoc network. Supports small form factor micro boards.

Iyaya

• Yavutaki ena tekinolaji ni OFDM, two-way broadband wireless link equipment.
• Business interface: 3 wireless transparent transmission Ethernet ports, 1 wireless transparent transmission RS232 serial port, 1 TTL control serial port ✔ Dual antennas: SMA connector, primary and secondary antennas, dual-transmit and dual-receive mode (2T2R), support MIMO
• Veilawalawa ni cakacaka ni veigacagaca ni veigacagaca: 566~678MHz, 1420~1530MHz, support automatic frequency selection within the frequency band
• iWiwisagale ni veiyalaki: 1.4MHz, 3MHz, 5MHz, 10MHz, 20MHz, 40MHz, air interface rate up to 100Mbps ✔ Modulation method: Veisau totolo ni QPSK/OM16/MAM64.
• iTuvatuva ni Veitaratara: dusia na veika me kilai, veitaratara veitaratara veitaratara ena veiyasana levu, Mesh network (vakataucokotaki), a central node can connect up to 31 access nodes. ✔ Wireless transmission power: 300mW*2
• Na itikotiko ni kena ciqomi na veika bibi: Sensitivity -95dBm at 20MHz bandwidth.
• Support AES128 encryption and decryption.
• Device configuration and wireless working status can be viewed through the network port Web UI or the control serial port.
• Kakana ni kaukauwa: 12~18V
• Oi rau na gacagaca: 83.7*61*19VV (excluding connectors protruding from the housing, kei na so tale.).
• Bibi: Less than 140g

Veisemati

veisemati	illustrate
RJ45*3	3 individual 4Pin PH1.25mm seats,3 Each Ethernet port device is in bridging mode(VEIYA NI VEIQARAVI same address)
VS232	VS232 gacagaca ni itukutuku tudei,3Pin PH1.25mm Spacer
C-TTL	3Pin PH1.25mm Seat, control serial port, TTL level
Kaukauwa ena	XT30PW-M Seat, power input interface
ANT1	SMA External threaded inner hole, veiyaca ni ivakatakarakara levu ni iyaca
ANT2	SMA External threaded inner hole, auxiliary antenna interface

RJ45 ethernet port
The three Ethernet ports are internally bridging (with the same IP address), and the wireless network port is in the transparent transmission mode of IP data.
For applications that require HDMI/SDI/AV/AHD video veisoqaqa, the video transmitter must add H265/H264 encoding board, which can be directly connected to the 4Pin Ethernet port for matching use.

RS232 data serial port
1 channel RS232 serial port for transparent data transmission, 3PIN PH1.25mm spacing socket, the signal of each PIN pin is shown in the figure below. The default baud rate is 115200, which can be changed through the Web UI or the AT command of the control serial port.

Control serial port
Control serial port (C-TTL), 3PIN PH1.25mm pitch socket, see the above picture for the signal of each PIN pin. The upper computer can configure and view the parameters and working status of the wireless link device through the AT command of the control serial port.

Working light
LED1: Red power indicator light, always on when the power supply is normal.
LED2: blue indicator light.
LED3: Green indicator light. The working status of LED2 and LED3 is as follows:

Central node	LED2: Karakarawa indicator light is always on LED3: Drokadroka indicator light does not shine
access node	LED3: Drokadroka indicator light is always on after the link with the central node is successfully established
	LED2: Karakarawa light indicator wireless link signal strength: Strong wireless link signal strength: LED2: Karakarawa Flash one time per 30 na sekodi; Normal wireless link signal strength: LED2: Karakarawa Flash one time per 6 na sekodi; Weak wireless link signal strength: LED2: Karakarawa Flash one time per one second;

Ivolakerekere:

The use of wireless video data RC control link can realize long-distance two-way wireless data communication, point-to-point two-way communication, and point-to-multipoint star network two-way communication.

In point-to-multipoint communication, if two access nodes need to communicate through the central node, each node is in the same wireless local area network, and all access nodes and the central node share the wireless working bandwidth, and the device will automatically average Assign system speed. The data transmission from the central node to the access node is called the downlink, and the data transmission from the access node to the central node is called the uplink.

In point-to-point or point-to-multipoint communication, the downlink and uplink share the wireless working bandwidth. When the device is shipped, the default setting is the ratio of uplink rate to downlink rate = 4:1. O koya gona, if the device is used to transmit IP Camera video data, the IP camera should be connected to the access node.

The device will automatically and dynamically adjust the wireless transmission rate according to the carried business data stream. When the amount of carried business data is smaller, the transmission distance will be farther under the same conditions. O koya gona, when the device is used to transmit IP Camera video data, the wireless transmission distance can be improved by setting appropriately reducing the IP Camera video encoding bit rate.