Guía del usuario de la red IP MESH Ad Hoc

Guía del usuario de la red IP MESH Ad Hoc

Version number: iVcan-20230606

Brief introduction

• Our Ad hoc network communication radio station, as a mobile self-organizing network, supports any network topology.
• Unlike traditional wireless networks, it is a wireless broadband system with no center, repartido, relé de múltiples saltos, enrutamiento dinámico, fuerte invulnerabilidad, and good scalability.
• Some routing protocols complete the wireless communication between nodes through wireless multi-hop forwarding.
• Un sistema de transmisión de red inalámbrica de banda ancha distribuida ad hoc con un protocolo de transmisión de capa MAC eficiente y un protocolo de enrutamiento de dos capas..
• All nodes are completely equal, without any infrastructure, and can quickly build a dedicated self-organizing network between mobile nodes, provide instant adaptive communication, have excellent broadband performance, and support the real-time transmission of multimedia information such as video coding and audio coding.
• The system technology has the advantages of strong anti-interference ability, alta eficiencia espectral, larga distancia de transmisión, capacidad anti-decoloración, y fuerte capacidad de difracción.
• Puede realizar funciones de transmisión de datos inalámbrica bidireccional en tiempo real y de alta calidad en entornos complejos y sin línea de visión..

Technical Features

• There is no need to set up a central station and complex system configuration. After the site is powered on, automáticamente formará una red, and the communication can be started in “seconds”;
• Topología arbitraria, relé de múltiples saltos, reenvío de retransmisión;
• Los atributos lógicos de cada nodo se pueden configurar de forma flexible.;
• En el presente, the same frequency network can support the interconnection of ≥32 nodes;
• El canal está cifrado con AES.;
• The system data bandwidth peak value is 90Mbps;
• Fuerte capacidad anti-interferencia, alta eficiencia espectral, larga distancia de transmisión, antiinterferencia
• Strong falling ability and diffraction ability

Parámetros técnicos

• Frecuencia de comunicación: 1412~1452MHz, adjustable in 5MHz steps;
• Poder de transmision: 2*30dBm (2*1W), 1paso de dBm ajustable。
• Modo de ancho de banda: 5 / 10 / 20 megahercio;
• método de modulación: multiportadora TDD-COFDM;
• Modulación portadora: BPSK/QPSK/16QAM/64QAM (adaptativo o fijo);
• sensibilidad de recepción: -98dBm a 10 MHz;
• Communication distance: 30km (ground-air/air-air line-of-sight), 8km (ground-ground line-of-sight);
• Communication rate: peak 90Mbps (adaptado);
• Retardo de transmisión: Single jump about 2ms；
• Multi-hop capability: hasta 8 video jumps;
• Start time: ≤25S;
• tiempo de acceso a la red: menos que 1 segundo;
• Conmutación de ruta: menos que 1 segundo;
• interfaz de datos: puerto de red x 2, RS232 x 2;
• El consumo de energía: 2~8W
• Nivel de protección: IP65;
• Temperatura de trabajo: -40~ + 70 ℃;
• Dimensiones: largo: 72.8mm*width 47.3mm*height 17.9mm
• Peso: 78gramo

Software operation Instructions

Support 5M, 10METRO, and 20M bandwidth, real-time graphical interface display, real-time map indication, etc..

The software disables DHCP by default, and the default IP address is 192.168.17.1 If you forget the address, please connect the 9th pin of the 26PIN cable to the ground to reset the parameters.

Enter the IP address of the module in the browser, and the default username and password are both admin. It takes about 20s for the module to connect to the network from power-on. The recommended browser is Chrome.

After entering, it defaults to simple mode, click expert mode to unlock more settings, suitable for professional debugging.

Status section:

Visión de conjunto:

Topology map: (automatic refresh is turned off by default to save bandwidth, you can check automatic refresh)

Check only the display path, you can know the direct jump point relationship of each module

Check the details to judge the data connection status of each module. These are displayed dynamically in real time

Click Details: You can know the specific situation of each module directly:

Terminal state:

Ad hoc network: You can remark the name, por supuesto, it can also be operated in the terminal state.

Spectrum scanning: Check the interference of each frequency band. por supuesto, the frequency bands of different modules are purchased, and the scanning frequency bands are different.

Map: (por supuesto, to know the location information of each terminal, GNSS modules such as GPS or Beidou need to be installed)

Support tile maps, image maps, network maps, etc..

Configuration section

Modo: 1. MESH node or bridge configuration

2. Wireless configuration:

2.1 Transmission power configuration, the power of different products purchased is different.

Canal de Banda ancha: 5M 10M 20M 40M

Canal: Different channels are used to purchase different products

The coverage distance (metros) needs to be filled in according to the actual situation. If it is set to 3000 metros, it is impossible to actually run to 5000 metros.

Number of Antennas 2

Fixed MCS rate: Can be set to off for automatic selection. If you want stable transmission, it is recommended to set the manual, distancia (MCS0 to MCS15)

Ancho de banda, Modulación, Tarifa

Limit MCS rate: It is recommended to enable it. After enabling it, if the fixed rate is MCS4, the software will automatically select the best modulation method from MCS0 to MCS4 during the test.

		5METRO	10METRO	20METRO	40METRO
MCS0	BPSK 1/2	1.7METRO	3.3metro	6.5METRO	13.5METRO
MCS1	QPSK 1/2	3.2metro	6.5METRO	13metro	27metro
MCS2	QPSK 3/4	4.8metro	9.8metro	19.5METRO	40.5METRO
MCS3	16QAM 1/2	6.5METRO	13metro	26METRO	54METRO
MCS4	16QAM 3/4	9.7METRO	19.5METRO	39METRO	81METRO
MCS5	64QAM 2/3	13metro	26METRO	52metro	108METRO
MCS6	64QAM 3/4	14.5METRO	29METRO	58.5METRO	121METRO
MCS7	64QAM 5/6	16METRO	32.5METRO	65metro	135METRO
MCS8	BPSK 1/2	3.2metro	6.5METRO	13metro	27metro
MCS9	QPSK 1/2	6.5METRO	13metro	26METRO	54METRO
MCS10	QPSK 3/4	9.7METRO	19.5METRO	39METRO	81METRO
MCS11	16QAM 1/2	13metro	26METRO	52metro	108METRO
MCS12	16QAM 3/4	19.5METRO	39METRO	78METRO	162METRO
MCS13	64QAM 2/3	26METRO	52metro	104METRO	216METRO
MCS14	64QAM 3/4	29METRO	58.5METRO	117METRO	243METRO
MCS15	64QAM 5/6	32.5METRO	65metro	130METRO	270METRO

From MCS0 to MCS7, two wireless ports send the same data in order to improve stability during the movement.

From MCS8 to MCS15, the two wireless ports send different data, which can make the rate X2

If it is in a mobile state, it is recommended to use BPSK or QPSK to transmit data. 16QAM and 64QAM are suitable for use with fixed transmission.

If MCS8 to MCS15 is used, it is recommended that the antennas of the two ports be 90 degrees from each other, por ejemplo, one is vertical and the other is horizontal.

If drones are used, MCS0 to MCS2 is recommended.

The greater the bandwidth, the lower the sensitivity. The same goes for modulation.

above rate unit bps

3. Red:

4. User management:

5. Sistema

6. Tools Configure serial port, GPS/Beidou/GNSS, 4G/5G access, and other parameters

6.1 Multi-device management, in the upper right corner, you can log in and manage users remotely, and it is also a real-time dynamic interface display or map display.

6.2 Serial port software settings:

Select Expert Mode, Herramientas, and UART Interface.

choose new

Atención, if you use the serial port to transmit serial data, you have to choose ttyS0 (COM1 of hardware) and ttyUSB0 (COM2 of hardware), ttyATH0 is invalid, modo: red

velocidad de transmisión 115200, bit de parada 1, parity none.

Nombre 1, protocol UDP, Recopilamos varios tipos diferentes de información para diversos fines para brindarle y mejorar nuestro Servicio., 192.168.55.100 (the IP address here is the IP address of the other device, por ejemplo, input the IP of the computer for the computer, and input the IP of the device for the device).

Puerto 20005, 20003. Choose a port number

The computer’s IP is set to a fixed 192.168.17.100

Short the TX RX pins of COM1 and COM2 of the device.

Use the TCP UDP test tool to fill in the IP and port of the device.

Send it to loop back the data.