Te mau hoho'a video e te mau matini haruharu no te Camera, drone video download link, COFDM
Wireless Video Transmitter for Camera, HDMI HD H265 264 1W/2.5W 1080P60
Tabula ohipa
No te faaohiparaa
- Full set HDMI input, HDMI output for long-rang Video Transmission.
- HD Wireless Video Transmitter and Receiver kit for CCTV Security cameras, Wedding DSLR camcorders,
- HDMI CVBS AV input on the Wireless Video Transmitter, Receiver has Ethernet / RJ45 / IP output to the computer, notebook for live streaming
- Wireless video transmitter for conference rooms (There are some obstacles between transmitters and receivers, NLOS: none-line-of-sight)
- Wireless 1080p video transmitter and receiver for Drone UAV video data downlink from the air to the ground
Transmitter Advantage
- This high-definition digital wireless video transmission transmitter includes an HDMI / CVBS (analog AV Audio Video)encoding board, a COFDM modulation module, and a small 1watts or 2.5 watts PA power amplifier module.
- The entire box is made of a CNC aluminum alloy shell that is small and light. The transmission resolution is excellent, and the transmission distance is long.
- Modulation using COFDM.
- By default, H265/H264 video encoding supports up to 1080P/I @60fps.
- AES256 encryption is adopted.
- Non-line-of-sight high-speed mobile transmission is supported. (Up to 800km/hour, support UAV Drone video download link)
- Support to configure the center frequency, wireless bandwidth, transmission stream, and so on parameters. (How to Configure?)
Transmitter Input Output
AV input interface:
SD input interface, 4PIN 1.5mm pitch socket, audio support Mic in or Line in input (specified at the factory before shipment). PAL or NTSC format can be set through the parameter panel. (How to change PAL / NTSC video format?)
TA'O (PIN) | faaiteraa |
AL | audio input Left channel |
AR | audio input Right channel |
GND | Te mau mana'o tauturu no te tuatapaparaa e |
AV | mana'o no te faahoho'araa |
Configuration Interface:
Configuration serial port (Hi'opo'araa i te tereraa o te ohipa), 4PIN 1.5mm pitch socket, TTL no 3.3 V. The 5V signal is used to supply power to our parameter configuration board.
Vauvauraa parau:
One-way transparent data serial port (UART itepiri), the serial port data will be unidirectionally transmitted to the data serial port of the corresponding receiver through the COFDM wireless link. 3PIN 1.5mm pitch socket, the default shipment is TTL 3.3V level, and it can also be specified as a standard RS232 level serial port when shipped.
Te faataaraa o te taata horo'a
Vauvauraa | |
HD video input | Standard HDMI Interface |
SD video input | 4PIN 1.5mm pitch connector (CVBS Analog Audio Video Input) |
One-way transparent data transmission serial port | 3PIN 1.5mm pitch connector, the default shipment is TTL3.3V level. The standard RS232 level can also be optional before shipment. |
Configure Serial port | 4PIN 1.5mm pitch connector, TTL3.3V. It can be connected to our Parameter Configure board, and can also be connected to a PC or another host computer |
Horo'araa i te mana | Tûtira XT30P-M (12V Te mana haaputuraa) |
Vauvauraa antenna | SMA male thread inner hole |
Wireless modulation transmission | |
Wireless modulation | COFDM |
Te huru IFFT | 2ITE |
wireless bandwidth | 1MHz~8MHz Adjustable, 1Taahiraa KLong |
FEC | 1/2, 2/3, 3/4, 5/6, 7/8 |
Tiai i te Ekalesia | 1/32, 1/16, 1/8, 1/4 |
Constellation | QPSK, 16QAM, 64QAM |
Wireless Code stream | 0.5Mbps to 31.67MTe mau nota (bites per second) |
Working frequency Band | Optional working frequency band:
300~360MHz; 350~400MHz; 450~500MHz; 520~560MHz; 580~620MHz; 680~720MHz; 820~860M ÏAD. Other working frequency bands between 200~860MHz can be customized. The center operating frequency is configurable, with a step of 1KHz. |
Mana haponoraa | 1W (30dBm) or 2.5W (34dBm) |
Audio and Video processing | |
support video input | default single-channel video input encoding transmission: HD or SD. Video input is automatically detected after power is on. If connected at the same time, the device defaults to the preferred HDMI input, and can also be changed to the preferred AV input.
Optional dual video input simultaneous encoding and transmission. |
Supported video formats | 1080@60P, 1080@50P, 1080@30P, 1080@25P, 1080@24P, 1080@60I, 1080@50I, 1080@30I, 720@60P, 720@50P, 720@30P,
720*480 60Ua(NTSC), 720*576 50Ua(PAL) |
Video Encoder | H265 or H264 |
Mau manao no te faaroo | HDMI embedded audio or analog CVBS Right / Left Audio Input |
Hohoa no te faaroo | AAC, 16e mea iti, ana'iraa hau (rû), 32Mga Eso |
Encryption and Decryption | AES256 |
Faito | 10.5*5*2.7tenetimetera |
Teimaha | <140 grams |
Te mana haaputuraa
Ta te mana |
DC 12V power supply (11~13V)
1W PA power amplifier: the power consumption is less than 15W; 2.5W PA power amplifier: the power consumption is less than 23W. |
Te taere | H265: 0.2~0.3 second; H264: 0.05-0.13 te piti |
Transmitter Dimension
Wireless Video Transmission Receiver
Receiver Advantage
- HD video COFDM wireless receiver with HDMI/CVBS/Ethernet/USB output interface
- Mahana RTSP server that allows video streaming over Ethernet for remote decoders. (Parau, rtsp://192.168.0.215/testStream ; port number should be 554, Aita 8080) How to set RTSP player?
- Allows remote Android device decoders to stream video over USB. (Splayer Android APK V5.0_2017)
- Supports displaying character strings on the video display screen alongside the video in OSD mode.
Te afata apo parau
- Dual diversity Antenna fariiraa i te
- Supporting working frequency band:160MHz ~ 860MHz, the center operating frequency can be configured;
- Wireless bandwidth can be configured;
- Dual antenna receiving sensitivity -100±1dbm (QPSK 8MHz);
- Wireless i te fariiraa i te haamaramaramaraa no te huru o te (eg Received signal strength, reva vauvauraa faito, data bit rate, operating frequency, wireless bandwidth, te tahi atu a.) can be selected to be superimposed or not displayed on the video screen via the OSD switch button, and can also be output to the serial port (tano);
- Low-latency H264 hio decoding, with support for 1080P@60 decoding and playback;
- Noatu i te faaroo e te video (HDMI, CVBS, USB, and Ethernet interface output at the same time):
- HDMI type A port audio and video output
- CVBS (lotus head) AV no te faaroo e te video noatu
- USB port output Video stream to mobile phone/tablet for decoding and display
-
Ethernet RJ45 output Interface for living stream, RTSP player support
-
Patururaa AES256 decryption video reception
-
Video recording via TF card or USB disk is supported.
-
Horoa 1 serial port for one-way transparent data transmission;
-
Provide a serial port for parameter configuration for working settings (such as central working frequency, wireless bandwidth, and receiving decryption password);
-
Te mana haaputuraa, 6~ 15V,
-
Working power consumption: 230mA@12V
-
Te parau: 11.5x9x3.4cm
-
Teimaha: 255 grams.
Receiver Input Output
Noatu te Video HD | HDMI type “A” Connector |
Te mau hoho'a video no ni'a i te mau hoho | RCA Connector |
Noatu i te faaroo | Embedded HDMI and RCA Connector |
Manao RF | Two SMA |
Mana i roto | 3PIN PH2.54mm Connector |
USB Host | Type A connector |
Te mau haamaramaramaraa no ni'a i te UART(3.3V) | 3PIN PH1.25mm Connector |
Hi'opo'araa TTL UART(3.3V) | 4PIN lockable Connector (from left to right, TX, RX, GND, 5V) |
Ethernet | RJ45 |
TF-Card | TF-Card slot |
OSD Key | Switch key for OSD-display |
Rec Key | Switch key for Video recording |
COFDM Video Transmitter and Receiver full-set
TE MAU NOTA
Please use the parameter configuration board to check.
More operation guide for the parameter configuaration board, A hio https://ivcan.com/parameter-configuration-panel-quick-operation-guide/
- Keep the antenna as high as possible because the ground absorbs the signal.
- Try to be at point B instead of point A. Because according to the transmission principle of the antenna, it propagates in an umbrella shape. The signal at point A is often very weak.
- The Transmitter frequency range can change to 1.4G or 1.34G.
- The receiver frequency range only supports 170-860Mhz, if you need 1.4G or 1.34G, you need to install a frequency down converter block at the receiver.
- We don't have the frequency down converter block now, maybe you can contact the below supplier. (Performance is much better than China supplier now)
- https://www.ettus.com/product-categories/rf-daughterboards/
- https://www.vislink.com/product/l3025-down-converter/
- https://www.kuhne-electronic.com/funk/en/shop/leistungsverstaerker/prof-heat-sinks/KU+LNC+1215+C+PRO+Down+Converter/?card=1839
- Above parameter LO frequency choose 1000MHz.
This model COFDM wireless video transmitter support video source input connector, HDMI, CVBS AV, SDI, IP ethernet RJ45, and AHD, please tell us what video type you need before delivery.
TE MAU TAMARII NO TE FEIA APÎ: 338.0MDT ÏP: 4.0MHz; RF indicates the central operating frequency point, BW indicates the operating bandwidth
QPSK AO: 2/3 GI: 1 /16 ; QPSK is the modulation method, CR is the convolution code rate, GI is the guard interval
TE TAU: 3.90Mbps ; TE MATA'I, o te faito ïa o te mata'i
VBR: 3.05Has AES OFF ; VBR o te faito video ïa, E ERE te AES OFF i te hoê tapao
SIG1: 27 SIG2: 22 ; SIG1 refers to the received signal strength of the antenna near the HDMI port, SIG2 refers to another antenna
taata papa'i 1: 0.14% taata rahi2: 100.00% ;ber1 refers to the receiving bit error rate of the antenna near the HDMI port, ber2 refers to another antenna
REC TUPOHE AITA E Haaputuraa ; TUHAA PURERAA NO TE PO'MAHANA MAA |
Please check here.
There are COFDM wireless video transmitter boards, PA power amplifiers, and cooling fans.
E mea papû
A hi'o i te hono i raro nei
COFDM Relay Repeater module for drone UAV wireless video transmitter and receiver Vcan1870
From some UAV customers have measured 50km when they are testing, and the height of the UAV is about 300 metera.
- If the transmitter modifies the wireless parameters such as constellation, GI, CR, and BW, the receiver must be restarted to lock and display normally.
- Another possibility is that your transmitter modifies the constellation parameters through the AT command, but the parameters are not actually written into the baseband board. You need to restart the transmitter board to confirm.
- Our one-way cofdm video transmission is not designed to consider your current usage scenario (fast switching frequency).
- This may not work, the delay of TX switching frequency involves many aspects, such as the delay of the encoder board itself (currently the main program processes parameter changes in a cycle of about 1 te piti), and the processing delay of the baseband board, so add It takes about 2 second to switch. The processing delay of the encoder board can be squeezed to within 1 second by modifying the firmware, but the delay of the baseband board is not easy to squeeze, and the most important thing is that it is not easy to update the firmware (you must return to the factory to use our equipment to update the firmware).
- Summarize:
The encoder board may be able to reduce the processing delay of 1 second by updating the firmware, but the delay of the baseband board cannot be squeezed, so the final optimized delay is about 2 tetoni.
- Our Vcan1726 can support one HDMI and one auxiliary CVBS audio and video input at the same time, which can be connected to external microphones and power amplifiers.
- The current software can only support one sound source, which can be modified and selected through the parameter configuration board, HDMI sound, or CVBS sound, and cannot handle two channels of audio at the same time.
- Because COFDM is a one-way transmission, both video and audio can only be transmitted in one direction. From the transmitter to the receiver, the audio cannot have a two-way intercom, just like an ordinary radio, which can only broadcast in one direction.
The UART command is here.
Set Input Sources Command (switch HDMI / Manao CVBS)
Faanahoraa | ATSU$(vin),$(ain)_ Hi'oraa maitai: ATSU0,1 _ |
Parameter | 1. Video input selection VIN: 0 let the system detect; 1 force CVBS input; 2 force hdmi/SDI input 2. Audio input selection AIN: 0 let the system detect; 1 force analog input |
Faaohiparaa i te | Used to meet specific application requirements (Hi'oraa maitai: HDMI/SDI input video, MIC input audio) |
Return Value | Hi'oraa maitai: ATSU0,1_ ATSU0,1 OK |
Oroa | setting command, power-off save. |
Get Gain Audio Input
Faanahoraa |
ATSAIS(lin),(ain vol)_ Hi'oraa maitai:ATSAI0,50_ |
Parameter |
Analog audio input mode selection lin: 0 mic in;1 line ine Analog audio input volume control ain vol: mic in recommended 50; line in recommended 0 |
Ohipa | Used to set analog audio input parameters |
Mana'o | Ei hioraa: ATSAl0,50_ ATSAI0,50 ok |
Te mau mana'o |
Set the command and save it after power off. ain vol setting range [-78,80] |
Te vai noa ra te hoê uiraa?
A farerei mai na ia matou no te tahi atu mau haamaramaramaraa.
A hapono i ta outou uiraa
COFDM Video Transmitter Frequency customize to 664Mhz
How to upgrade the COFDM wireless video receiver newe firwmare