COFDM Relay Repeater
COFDM Relay Repeater module for drone UAV wireless video transmitter and receiver Vcan1870
Tabula ohipa
Omuaraa
The module is a relay module, not a completed item. Customers need to add a power amplifier, filters, and receiving and transmitting antennas for it to work effectively. These need to be customized according to the two working frequencies selected by the customer.
To prevent interference, the drone employs a single frequency (e.g. 400Mhz) for communication with the relay, and a different frequency (e.g. 700Mhz) for communication between the relay module with the receiver. The separation between the two should be as large as possible.
Hohoa
- Wireless Video COFDM Video Data demodulation and re-modulation
- Te haponoraa i te mau tapa'o i roto i te NLOS e te tere-vitiviti-raa (less than 600km/hour)
- Te pinepineraa i te rave i te ohipa, bandwidth, mana haponoraa, te tahi atu a (Special Parameter Configure Tool or UART STM32 LoRA )
- Lowest latency 200-300 faaî i te taata
- Widely frequency range 200Mhz-3000Mhz
- Patururaa AES256
- Bandwidth 1Mhz-8Mhz faahepo ore
- Video signal repeater for long-distance
Omuaraa
Specification:
IO
Manao RF | Two SMA females (to receive the signal) |
Te iritiraa o te MAU PARAU APÎ | vahine MSX (to send out the signal again) |
control UART | 4PIN PH1.25mm Connector |
Mana i roto | 2PIN PH2.54mm phenix Connector |
TF-card | For firmware update |
Power led | red LED, constant light when the device is normally powered |
Link led | green led, blinks on transmitting the received data |
Demodulation and Modulation
Modulation Formats | COFDM(DVB-T) |
Te feia e farii nei, a faaite mai. | 2ITE |
Bandwidth | E nehenehe e ta'ita'i mai te 1M Pahonoraa e tae atu i te 8MWil, taahiraa na ni'a i te 1K Tata'u |
FEC | 1/2, 2/3, 3/4, 5/6, 7/8 |
Tiai i te Ekalesia | 1/32, 1/16, 1/8, 1/4 |
Constellation | QPSK, 16QAM, 64QAM |
Bitrate | 0.5Mps e 31.67 Mp |
RF Received
Te tapea pinepine | 160MHz ~ 860MHz (need an extra down converter block for 860-2300Mhz) |
Faito o te taahiraa avae | 1KLong |
Tapao itea | -97±1dBm(BW=8MHz, QPSK, CR=2/3, GI=1/16) for one channel and add 3dBm for two-channel |
RF Transmitted
Te tapea pinepine | 200MHz~2300MHz(other bands can be supported with special manufacturing) |
Faito o te taahiraa avae | 1KLong |
Power out | Configurable, maximum -5dBm(subject to frequency) |
Te hi'opo'araa e te haavîraa
This COFDM relay repeater module can complete setup with our Parameter Configure Tool or STM32+LoRA (or other devices) via control uart. With our parameter configure too, the following parameters can be set:
– RX Received frequency (F1) e te Pŭpŭ no te Tino (B1)
– TX Transmitted frequency (F2), bandwidth (B2), FEC, mau taime paruru, constellation, and transmission power
Te anuvera
Faataaraa papû maitai: 0° to +70°C Ambient
Haaputuraa maa a te: –40° ia +80°C
Te mau titauraa no te mana
Te mau rave'a i roto i te parau: 7~24VDC
Ta te mana: <250mA@12V
Huru pae tino
Te parau: 73x51x15mm
Taotao teimaha: 32.4 grams
TUHAA PURERAA NO TE PO'IPO'I MAHANA MAA
The AT commands mainly used in the COFDM Wireless Relay Repeater are ATDR, ATSD, ATGD, ATSR, ATGR, and ATGB. For the introduction of specific commands, see the document.
TE MAU NOTA
- Our COFDM Video Transceiver relay repeater supports 170-860Mhz. The COFDM transmitter also supports 2300Mhz, but the COFDM receiver only supports up to 860Mhz, 861-930Mhz receiver our COFDM-221 supports, over 930Mhz-2300Mhz needs to plus the frequency downconverter block to support.
- Our COFDM relay repeater module supports all the COFDM transmitters and receivers, the transmission distance depends on your external power amplifier and filter support.
Te vai noa ra te hoê uiraa?
A farerei mai na ia matou no te tahi atu mau haamaramaramaraa.
A hapono i ta outou uiraaThe below model is good for a two-way TDD bidirectional link of the Wireless relay transmitter and receiver or wireless transmitter and receiver relay repeater.