HDMI To IP encoder modulator CVBS H.265 H.264 encoding board PCBA Ethernet RTSP UDP for UAV Drone Robotic
Talaan ng nilalaman
pagpapakilala
There are many HDMI encoding boards on the market. Have you met these problems?
- The delay is too long
- The encoding format cannot be customized
- UART AT remote control or operation cannot be used.
- Can not support HDMI and CVBS dual video input encoding
This encoder board supports HDMI, SDI, CVBS video input, at IP ethernet RJ45 living stream output, most applications are for wireless video transmitters, which can encode the HDMI or CVBS video signal to the digital living stream by H.264 or H.265, and transfer it to the receiver, CVBS to IP converter.
The HDMI and Composite CVBS video to IP ethernet stream encoder modulator module board parameter can be configured by UART software modification. Please contact us if you need to customize a similar function to meet your project.
kalamangan:
Ultra-Low Latency
H265 or H264 support
HDMI and CVBS Dual Encoding
Two Audio inputs can switch
Web UI o serial port UART AT command configuration management
- Ultra-low latency H.265/H.264 audio and video encoding maximum support 1080P60 real-time video capture and encoding
- The HDMI or AV input is encoded and outputted to a wireless module through the Ethernet port. The video encoding bit rate can be adjusted dynamically.
- Suportahan ang audio input at audio decoding output. (Remote operate by UART AT command choose HDMI or CVBS audio)
- You can choose between HDMI or AV encoding for two videos with the option to control the input source using an AT command.
tampok
Ang board ay nagpapatupad ng H.265/H.264 audio at video compression encoding, Sinusuportahan ng hanggang sa 1080p @ 60fps encoding, and is backward compatible with other resolutions and frame rate encoding.
Audio at video input
- interface ng HDMI(audio+video):1080 60P,1080 50P,1080 30P,1080 25P,1080 60ako,1080 50ako, 720 60P,720 50P,720 30P, …, iba't ibang mga mode adaptive (1080p, 1080ako, 720p, 1024×768, 1280×1024);
- AV in the interface (audio + video):720×480 60ako(NTSC),720×576 50ako(PAL), mode agpang. through the AV interface, it can be Line in Mic in.
- Ang default na audio input ay ang parehong bilang ang input interface ng video.
- The audio input interface can also be configured through the Web UI when the serial port detects audio.
- The audio and video source signals are encoded, at ang audio at video source acquisition interface ay maaari ding i-configure sa pamamagitan ng configuration serial port.
- The audio and video source acquisition interface can be dynamically switched through serial port commands during system operation.
Video encoding: H.265 o H.264 format, ang pag-encode ng bit rate ay maaaring i-configure.
Audio encoding: AAC encoding. - Sa pamamagitan ng programming espesyal na firmware HDMI+AV ang sabay-sabay na pagkuha at pag-encode ng board Audio output(Audio out)
- Ang board ay may built-in na audio decoding output function(Pumila sa labas), na maaaring konektado sa isang panlabas na headphone o audio power amplifier. Na-decode at na-play ang audio.
Ethernet port (Ethernet interface)
supports our two-way wireless transmission modulator module, o iba pang third-party na two-way na link.
Wireless interface transmission( FPC Main interface)
ay maaaring konektado sa aming COFDM wireless transmission module, at maaari ding ikonekta sa aming two-way wireless transmission link module.
Data-UART
TTL 3.3V na antas, maaaring i-configure ang mga parameter tulad ng transmission baud rate. When the board is through a wireless link, ang data serial port ay ginagamit para sa transparent na paghahatid ng data.
Control-UART
TTL 3.3V na antas, na maaaring ikonekta sa aming panel ng pagsasaayos ng parameter o isa pang computer sa itaas upang i-configure ang sistema ng encoding board.
USB Host interface
pag-upgrade at pagpapanatili ng software. (optional USB recorder function)
Power supply ng boltahe
sumusuporta sa reverse connection na proteksyon ng power input, and supports the power input range of 7opsyonal na grado ng distansya. Nagbibigay ng 5V power output interface. Ang maximum na pagkonsumo ng kuryente sa pagtatrabaho ay 2.4W (1080P60 H.265 encoding), at ang pinakamataas na kasalukuyang ay 200mA.
Tagapahiwatig
kapangyarihan indicator, tagapagpahiwatig ng trabaho sa pag-encode ng video.
The HDMI to IP encoder board size ay 70x45x1.2mm (LWH)
Ang taas ng bahagi sa likod ay mas mababa sa 2.5mm, at ang taas ng front component ay mas mababa sa 6.8mm.
Lupon ng timbang
20.6 gramo.
Signal ng Interface
- AL (Audio in left), input ng audio sa kaliwang channel;
-
AR(Nasa kanan ang audio), kanang channel ng input ng audio;
-
GND, signal ground;
-
OF, analog input ng video. (Please ignore the color of the wiring, make sure the fourth jack is CVBS Composite video input.)
Control UART: Nilagyan ng serial port,4PIN 1.25mm pitch socket, TTL 3.3V na antas, ginagamit para sa pagsasaayos ng parameter ng board, ay maaaring konektado sa Sihaida parameter configuration panel o isa pang host computer.
USB interface:4PIN 1.25mm pitch socket, used for the encoder board software upgrade and maintenance.
Audio-out na interface:2PIN 1.25mm pitch socket, ang board ay may built-in na audio decoding output function(Pumila sa labas), na maaaring konektado sa isang panlabas na headphone o audio power amplifier. I-decode at i-play ang audio input mula sa network port.
Ethernet: Ethernet interface,4PIN 1.25mm pitch socket
application
- Done or UAV video encoding
- Robotic or mini-control vehicle
- Unmanned Vehicles UAV
- Unmanned Submarine
- The HDMI to IP board can be COFDM modulation module RCB stacked and assembled with a COFDM one-way transmission module. The connection interface is FPC Main (26PIN flat cable flexible cable interface). HDMI+AV encoder + COFDM Transmitter Module
- The HDMI to IP encoder board PCBA is connected to a two-way wireless link through the network port. Sa oras na ito, ang mga operating parameter ay maaaring i-configure sa pamamagitan ng network port Web UI. Halimbawa, itakda ang bit rate ng pag-encode ng video, Paraan ng pag-encode ng H264/H265, paraan ng pag-input ng audio, serial port baud rate, etc.
- The board can be connected to the Control-UART parameter configuration panel to set operating parameters.
- Bersyon ng interface ng HDMI: HDMI V1.4
- Rate ng Data ng Output ng Ethernet: 100COFDM wireless transmission system pagkalkula ng transmission rate
- Saklaw na temperatura ng operating: -40~85 degrees
- Mga katugmang Operating System: Naka-embed na Linux
Web UI management Parameter setting
Mga FAQ
Maaaring tingnan ng HDMI video na ito sa IP encoding board ang kasalukuyang configuration ng parameter sa pamamagitan ng network port Web UI at baguhin ito ayon sa mga pangangailangan ng application. sa pamamagitan ng network port browser http://192.168.1.30/ (ang IP address ng encoding board)
1. Pakisuri ang Web UI mula sa browser, sa larawan sa ibaba, kung ok ang input ng video source, then it will show the CVBS or HDMI at the red arrow.
2. Pakisuri ang HDMI encoding board LED light ay kumikislap o hindi.
Kung ito ay berde at kumurap, pagkatapos ay gumagana nang maayos ang video input source, kung hindi kumurap, then please check the video input source is ok or not.
The encoding bitrate can be configured. The default web server is set to 0.0 to represent auto (3.12Mbps will be used internally). Customers can modify this value. Halimbawa, it is possible to configure 1Mbps~2Mbps or even lower.
1. Large I-frames are prone to frame loss due to wireless transmission;
2. If the gop setting is large, the loss of the I frame will lead to a longer recovery time after the blurred screen;
3. The size difference between I frame and P frame is large, which will increase the transmission delay.
1、比如相机输入1080p60,那gop设置为60/120/180(不建议设置太大)
2、比如相机输入1080p25,那gop设置为25/50/75(不建议设置太大)
3、比如相机输入1080i60,由于需要去交织,所有实际编码是1080p30,那gop设置为30/60/90
从上面可以看到,由于输入相机帧率不确定,所以我们一般建议配置0(auto)
cvbs分制式,pal是25fps,ntsc是30fps
假设是pal,那gop设置25/50/75
1、大的I帧容易因为无线传输的原因导致丢帧花屏;
2、gop设置大,I帧丢失导致花屏后恢复时间变长;
3、I帧和P帧大小差别大,会增加传输延迟
Mangyaring i-download sa link sa ibaba.
Splayer_v4.2_2020.6.6
https://drive.google.com/file/d/1ihzUhfnx2Wo3zLO8UAs1aUQeLswonJD-/view?usp=sharing
Splayer_v4.3_2022.10.22
https://drive.google.com/file/d/1PQc-LZ55qGnjeMsjkHYSloHfY3NEUsGH/view?usp=drive_link
- We can modify the TS stream over UDP, but the TS stream is a non-standard TS stream that we have modified, which needs to be interpreted by our decoder board or special player (Download).
- If you agree with the RTSP protocol, VLC can play it; if you only agree with the TS stream (due to our non-standard modification), VLC cannot decode and play it, so we must use our special player. (Download).
- If you want to switch to the standard MPEG-2 TS stream to play with VLC, our software engineer can customize the firmware for you (this will take a few days) for an additional fee of USD500.
- We use non-standard mpeg-2 ts streams primarily for the following reasons:
- The standard mpeg-2 ts stream has too much overhead outside the effective data, making it unsuitable for use with cofdm;
- The standard mpeg-2 ts stream is difficult to implement the aes encryption function;
- The standard mpeg-2 ts stream is difficult to achieve serial port transparent transmission (used with our decoder board)
- If you don't need our decoder board, encryption and serial port transparent transmission, it is also possible to use standard mpeg-2 ts stream
- It is recommended that you try our player; in real-time performance, our player outperforms vlc.
The vlc player's algorithm does not take into account real-time performance; sa halip, it will constantly adjust its cache (only increase but not shrink). Ang resulta, the longer it is played, the longer the delay may be (especially when used with a wireless link)
1. SSL certificate is HTTPS protocol, our products do not support it now, only HTTP.
2. The default encoder board through the RTSP protocol, RTSP is not encrypted. You can set a longer password. And change it frequently.
3. If you want to encrypt, you need to use a pair of our codec boards (with encoder and decoder board as TX and RX), with UDP protocol, and they are using aes256 encryption. (Just like the bank level.)
oo, Oo naman, mangyaring makipag-ugnay sa amin. Let me list your demand at the below.
1. We need to take a composite analog PAL video signal and transmit it using h264 over MPEG2 TS. OK
2. The output must be playable through VLC. OK
3. UPD://@1030. OK
4. The output network stream packet should be 188 bytes standard mpeg2 TS. OK
5. Compression scheme is h. 264, CVBS PAL input and IP output. OK
Oo naman
Mangyaring suriin ang link sa ibaba
COFDM UART AT command for the transmitter and Receiver.
o
Download the COFDM Transmitter UART AT command PDF.
Please follow the checkpoints below to confirm.
- After connecting the encoder board with your computer by ethernet cable, the LED of RJ45 connector should be blinking or not. (to check the ethernet connection is ok or not)
- Is your computer configured with 192.168.1.x network segment ip?
- Have you modified the default IP address of the encoding board? If the IP address changed, maybe you can download and use the below software to find what IP address now.
- Or Directly connect the UART cable of the encoding board to the computer, and use the serial port debugging assistant to send the ATGIP_ command.get ip address command Operation Video at Youtube
format
ATGIP_
Example: ATGIP_
parametro
Hindi
paggamit
to query the current IP address of the receiving end
Return value
Example:
ATGIP_
ATGIP192.168.0.215 OK
pangungusap
- query command
- More COFDM UART AT commands, please check this link. https://ivcan.com/encoder-modulator-decoder-demodulator-module-parameter/
These parameters are determined by the camera, only the sensor has it.
One more question: In the future is there any possibility to incorporate these features in the output side of encoder (if we get volume orders) ?
Our Answer: These are the parameters of the isp, and our current encoding boards are all bypass isp (because we don't connect the sensor, we don't need and can't use the isp), so we can't add these parameters.
oo, CVBS input support NTSC and PAL, Automatic detection and adaptation
- ang parameter configuration board tool is mainly used for the COFDM module function. If you buy this HDMI / CVBS to IP encoder Vcan1746 separately, you don’t need to buy a parameter configuration board tool, you can adjust the parameters through the Web UI.
- Syempre, if you want to use the parameter configuration board tool to adjust some parameters of the encoder board, it is also possible.
- Halimbawa, the video encoding bit rate can be configured through the Web UI or changed through the extra parameter configuration board tool. The Web UI can configure all the parameters, and the parameter configuration board tool can only adjust some of them.
Ok, please check the below link
oo, kung kailangan mo, we can offer you the special firmware to have USB recorder function.
tanong: Does your USB DVR support playback on the encoded video?
sagot: Hindi, The USB has the record function. You need to play it on a computer, it can not playback on the encoder board directly.
- Do you mean HDMI or AV input, or do you need HDMI and AV to support two simultaneous inputs?
- Currently it supports either HDMI or AV input.
-
Vcan1746 can only choose one of HDMI/AV at present, other boards can meet the firmware you need, but this board only supports SDI + AV/AHD output.
-
If necessary, you can evaluate the board with SDI + AV/AHD input to see if it meets your requirements. If yes, our HDMI + AV input Vcan1746 can be made the same later.
-
If you really need to evaluate the HDMI + AV interface, please first buy Vcan746 and burn the default shipping firmware for testing. HDMI and AV can be selected for use. If there is a certain amount of follow-up orders, we can develop a special firmware to support HDMI+AV input at the same time.
-
The display of HDMI and CVBS video input by two channels at the same time is similar to Hikvision IPC, which is divided into main bit rate and sub bit stream. The main stream corresponds to HDMI, and the sub stream corresponds to CVBS.
- Now we can develop a new firmware to support HDMI and CVBS to live streaming at the same time, but the audio can only be selected from one of the two (the system selects HDMI audio/analog audio according to the video access situation).
Supported.
Our HDMI and CVBS input video encoding board has a USB interface, which can be used for USB recording. It can also be used as the input interface of a USB web camera.
Sa ganitong paraan, our video encoding board can convert the signal of your USB web camera into a network interface, while supporting ultra-low latency and supporting h264 and h265 encoding.
May tanong pa?
Mangyaring makipag-ugnayan sa amin para sa karagdagang impormasyon.
Ipadala ang Iyong Tanong
HDMI Video Sources Input IP Ethernet Output encoder, VLC RTSP operation
Industrial-grade temperature range from -40°C to 70°C Celsius test
Support HDMI and CVBS 2 video streams at the same time
How to get the IP address of the encoder back if you forget
More FAQ
HS Code
8517629900, Some of our customers use this HS code for your reference.
Special Function Custom Development
-
HDMI and CVBS Dual Video Encoding
-
USB has a video recording function.
-
Special handling of encoding formats to match your custom decoder board
скачать видеокодер