Дастури корбари шабакаи IP MESH Ad Hoc

Дастури корбари шабакаи IP MESH Ad Hoc

Version number: iVcan-20230606

Brief introduction

• Our Ad hoc network communication radio station, as a mobile self-organizing network, supports any network topology.
• Unlike traditional wireless networks, it is a wireless broadband system with no center, distributed, multi-hop relay, dynamic routing, strong invulnerability, and good scalability.
• Some routing protocols complete the wireless communication between nodes through wireless multi-hop forwarding.
• An ad hoc distributed broadband wireless network transmission system with an efficient MAC layer transmission protocol and a two-layer routing protocol.
• All nodes are completely equal, without any infrastructure, and can quickly build a dedicated self-organizing network between mobile nodes, provide instant adaptive communication, have excellent broadband performance, and support the real-time transmission of multimedia information such as video coding and audio coding.
• The system technology has the advantages of strong anti-interference ability, high spectrum efficiency, масофаи дароз интиқол, anti-fading ability, and strong diffraction ability.
• It can realize real-time and high-quality wireless two-way data transmission functions in complex and non-line-of-sight environments.

Technical Features

• There is no need to set up a central station and complex system configuration. After the site is powered on, it will automatically form a network, and the communication can be started in “seconds”;
• Arbitrary topology, multi-hop relay, relay forwarding;
• The logical attributes of each node can be flexibly configured;
• Айни ҳол, the same frequency network can support the interconnection of ≥32 nodes;
• The channel is encrypted with AES;
• The system data bandwidth peak value is 90Mbps;
• Strong anti-interference ability, high spectrum efficiency, масофаи дароз интиқол, зидди халал
• Strong falling ability and diffraction ability

Параметрҳои техникӣ

• Communication frequency: 1412~1452MHz, adjustable in 5MHz steps;
• Қувваи интиқол: 2*30dBm (2*1Дар), 1dBm step adjustable。
• Bandwidth mode: 5 / 10 / 20 МГс;
• усули талфиқи: multi-carrier TDD-COFDM;
• Carrier modulation: BPSK/QPSK/16QAM/64QAM (adaptive or fixed);
• гирифтани ҳассосият: -98дБм @ 10 МГц;
• Communication distance: 30км (ground-air/air-air line-of-sight), 8км (ground-ground line-of-sight);
• Communication rate: peak 90Mbps (adaptive);
• Таъхири интиқол: Single jump about 2ms；
• Multi-hop capability: то ба 8 video jumps;
• Start time: ≤25S;
• Network access time: камтар аз 1 дуюм;
• Routing switching: камтар аз 1 дуюм;
• интерфейси маълумот: network port x 2, RS232 x 2;
• истеъмоли Ҳокимият: 2~8W
• Protection level: IP65;
• ҳарорати корӣ: -40~ + 70 ℃;
• Андоза: дарозӣ: 72.8mm*width 47.3mm*height 17.9mm
• тарозу: 78г

Software operation Instructions

Support 5M, 10Мард, and 20M bandwidth, real-time graphical interface display, real-time map indication, ва ғайра.

The software disables DHCP by default, and the default IP address is 192.168.17.1 If you forget the address, please connect the 9th pin of the 26PIN cable to the ground to reset the parameters.

Enter the IP address of the module in the browser, and the default username and password are both admin. It takes about 20s for the module to connect to the network from power-on. The recommended browser is Chrome.

After entering, it defaults to simple mode, click expert mode to unlock more settings, suitable for professional debugging.

Status section:

Шарҳи:

Topology map: (automatic refresh is turned off by default to save bandwidth, you can check automatic refresh)

Check only the display path, you can know the direct jump point relationship of each module

Check the details to judge the data connection status of each module. These are displayed dynamically in real time

Click Details: You can know the specific situation of each module directly:

Terminal state:

Ad hoc network: You can remark the name, Албатта, it can also be operated in the terminal state.

Spectrum scanning: Check the interference of each frequency band. Албатта, the frequency bands of different modules are purchased, and the scanning frequency bands are different.

Map: (Албатта, to know the location information of each terminal, GNSS modules such as GPS or Beidou need to be installed)

Support tile maps, image maps, network maps, ва ғайра.

Configuration section

ҳолати: 1. MESH node or bridge configuration

2. Wireless configuration:

2.1 Transmission power configuration, the power of different products purchased is different.

маҷрои Channel: 5M 10M 20M 40M

Канал: Different channels are used to purchase different products

The coverage distance (метр) needs to be filled in according to the actual situation. If it is set to 3000 метр, it is impossible to actually run to 5000 метр.

Number of Antennas 2

Fixed MCS rate: Can be set to off for automatic selection. If you want stable transmission, it is recommended to set the manual, диапазон (MCS0 to MCS15)

маҷрои, талфиқи, Меъёр

Limit MCS rate: It is recommended to enable it. After enabling it, if the fixed rate is MCS4, the software will automatically select the best modulation method from MCS0 to MCS4 during the test.

		5Мард	10Мард	20Мард	40Мард
MCS0	BPSK 1/2	1.7Мард	3.3м	6.5Мард	13.5Мард
MCS1	QPSK 1/2	3.2м	6.5Мард	13м	27м
MCS2	QPSK 3/4	4.8м	9.8м	19.5Мард	40.5Мард
MCS3	16QAM 1/2	6.5Мард	13м	26Мард	54Мард
MCS4	16QAM 3/4	9.7Мард	19.5Мард	39Мард	81Мард
MCS5	64QAM 2/3	13м	26Мард	52м	108Мард
MCS6	64QAM 3/4	14.5Мард	29Мард	58.5Мард	121Мард
MCS7	64QAM 5/6	16Мард	32.5Мард	65м	135Мард
MCS8	BPSK 1/2	3.2м	6.5Мард	13м	27м
MCS9	QPSK 1/2	6.5Мард	13м	26Мард	54Мард
MCS10	QPSK 3/4	9.7Мард	19.5Мард	39Мард	81Мард
MCS11	16QAM 1/2	13м	26Мард	52м	108Мард
MCS12	16QAM 3/4	19.5Мард	39Мард	78Мард	162Мард
MCS13	64QAM 2/3	26Мард	52м	104Мард	216Мард
MCS14	64QAM 3/4	29Мард	58.5Мард	117Мард	243Мард
MCS15	64QAM 5/6	32.5Мард	65м	130Мард	270Мард

From MCS0 to MCS7, two wireless ports send the same data in order to improve stability during the movement.

From MCS8 to MCS15, the two wireless ports send different data, which can make the rate X2

If it is in a mobile state, it is recommended to use BPSK or QPSK to transmit data. 16QAM and 64QAM are suitable for use with fixed transmission.

If MCS8 to MCS15 is used, it is recommended that the antennas of the two ports be 90 degrees from each other, барои намуна, one is vertical and the other is horizontal.

If drones are used, MCS0 to MCS2 is recommended.

The greater the bandwidth, the lower the sensitivity. The same goes for modulation.

above rate unit bps

3. шабакаи:

4. User management:

5. система

6. Tools Configure serial port, GPS/Beidou/GNSS, 4G/5G access, and other parameters

6.1 Multi-device management, in the upper right corner, you can log in and manage users remotely, and it is also a real-time dynamic interface display or map display.

6.2 Serial port software settings:

Select Expert Mode, Tools, and UART Interface.

choose new

Диққат, if you use the serial port to transmit serial data, you have to choose ttyS0 (COM1 of hardware) and ttyUSB0 (COM2 of hardware), ttyATH0 is invalid, режим: шабака

Меъёри Baud 115200, истгоҳи каме 1, parity none.

ном 1, protocol UDP, IP address, 192.168.55.100 (the IP address here is the IP address of the other device, барои намуна, input the IP of the computer for the computer, and input the IP of the device for the device).

бандаргоҳ 20005, 20003. Choose a port number

The computer’s IP is set to a fixed 192.168.17.100

Short the TX RX pins of COM1 and COM2 of the device.

Use the TCP UDP test tool to fill in the IP and port of the device.

Send it to loop back the data.